Assa Abloy Sargent Passport 1000 PG User manual

1-800-727-5477 • www.sargentlock.com
A7807D 12/22
Installation Instructions
Passport 1000 PG
Copyright © 2012, 2022 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express
written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in dam-
age to the product and void the
factory warranty.
WARNING
Mortise Lock

2
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
1 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3 Hardware Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
4 Electronics Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
5 Parts Breakdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
6 Installation Instructions - Door Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
7 Installation Instructions - Change Hand of Lock Body. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
8 Installation Instructions - Installation of Lock Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
9 Installation Instructions - Installation of Outside & Inside Lever Assembly Lock Body . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
10 Installation Instructions - Installation of Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
11 Installation Instructions - Deadbolt Functions Only (82276 & 82277) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
12 Installation Instructions - Gasket Installation (Optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
13 Installation Instructions - Installation of Outside Escutcheon and Mounting Plate Assembly . . . . . . . . . . . . . . . . . . . 12
14 Installation Instructions - Installation of Inside Component Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
15 Installation Instructions - Installation of Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
16 Installation Instructions - Battery / Battery Pack Installation and DIP Switch Setting Verification . . . . . . . . . . . . . . . 14
17 Installation Instructions - Installation of Inside Escutcheon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
18 Installation Instructions - Application of Front Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
19 Setting up the LockLink™ and Contact Card for First Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
20 LockSet Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
21 Operational Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

3
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada
Statement: The term “IC:” before the radio certification number only signifies that Industry Canada technical
specifications were met.
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment
Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant
des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne
pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris
l’interférence qui peut causer l’opération peu désirée.
Warning
1
Designed specifically for the campus market, the SARGENT Passport 1000 PG Mortise Lock (powered by
PERSONA) provides offline card/PIN access control, as well as detailed audit capabilities.
• The PG Offline unit is available with both keypad and magstripe card technology, or magstripe only.
• The PG operates on six (6) “AA” alkaline batteries and may be used for both indoor and outdoor
applications.
Note: A weather-protective gasket is recommended for outdoor applications.
General Description
2

4
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
• Stand alone, battery-operated
• Complete lockset with on-board memory
• Available with or without keypad (magstripe only)
• ADA compliant
• Easily retrofits existing PERSONA door preps (mortise)
• Latch - Stainless steel
• Deadbolt - Stainless steel
• Guardbolt - Stainless steel, non handed
• Handing (RH/LH) can be specified but is easily field-reversible without disassembling the lock body
• Case - 12 gauge heavy duty wrought steel
• Outside lever controlled by any combination of keypad, magstripe reader, or mechanical cylinder
• Inside lever retracts latch and deadbolt
• Locks furnished for 1-3/4" doors. Can be furnished for other door sizes upon request (consult factory)
• UL Listed (3 hr.)
Hardware Specifications
3
Electronics Specifications
4
• Over 1 million users per door; 700 event transaction audit trail
• Multiple time zone and holiday access scheduling
• First-In unlock configuration, either by time or by valid time or by user (selectable)
• Input Power: DC 9V, 1.5A through 6 AA Alkaline Batteries or Electrical Power
• Card Coercivity: HiCo (4000 Oersted) or LoCo (300 Oersted)
PERSONA Campus™ Online Software Features
• Use existing magstripe ID cards (high or low coercivity)
• New keycards can invalidate and reactivate key cards/users – encoded quickly and easily through the
“Conference Guest Wizard”
• Assign pre-defined access patterns and access points as well as keycard start and end times (group or
individually)
• Importing student/personnel information is easy using the Import module
• Provide Deadbolt override at user-specified doors for groups or individuals
• Connect to an external database for seamless integration of common information
• Remote technical support is available
• PERSONA Campus Online Software runs as a standalone system on a single PC or networked using
existing TCP/IP networks

5
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
ITEM PART NO. DESCRIPTION
1 52-0757 Lens (Cliplite)
252-0736 Outside Passport Escutcheon (With Keypad)
52-0737 Outside Passport Escutcheon (Without Keypad)
3 52-3593 Slim Style Keypad Assembly (KP-PG Only)
4 52-0760 Light Pipe (Cliplite)
5 01-9299 4-40 X 3/16 Machine Screw
6 52-0741 LCU Card Reader
7 52-0742 Card Reader Mount
8 52-2501 Grounding Harness
9 52-3597 9V Battery Harness
10 52-3599 Wire Harness LCU to Inteface PCB
11 52-0875 PG Passport 1000 Spacer (Included only with 1-3/8" thick doors)
12 52-0748 Inside Mounting Plate
13 52-3804 Screw Pack
14 52-3906 Grounding Harness
15 52-0871 Wire Cover Plate
16 52-0751 Battery Cartridge
17 52-4245 Modular Component
18 52-3592 Inside Escutcheon Assembly
Parts Breakdown
5
2358910 12 13
1
4
6
7511
13
16
18
14
17
13
15
aPG Standalone With Card Insert and/or Keypad

6
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
ITEM PART NO. DESCRIPTION
1 See catalog Cylinder & Key Assembly
2 13-0140 Compression Spring
3 See catalog Blocking Ring
4 See catalog Cylinder Rosette
5 See catalog Mortise Lock body
6 77-2591 Tab Turn Lever Assembly
7 See catalog Inside Lever Handle
8 See catalog Outside Lever Assembly
9 82-0368 Spindle
10 82-3088 Inside Lever/knob Adapter Plate Assembly
11 01-1495 8-32 X 5/8 Machine Screw
12 See catalog Mortise Rose
13 82-0347 Spindle Spring
14 Cr-fhm1 1/4-20 X 1/2 Machine Screw
15 Cr-fhws 12 X 1-1/4 Wood Screw
16 82-0084 Outside Front, Stamped
17 01-0028 8-32 X 1/4 Machine Screw
12
13
14
15 16 17
8
1
2
3
4
5
6
7
9
10
11
Parts Breakdown
5
b8200 Series Mortise Lock

7
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
Installation Instructions - Door Preparation
6
aVerify Hand and Bevel of Door
Stand on outside/locked side of door when determining the door hand.
LH
Left Hand
Hinges Left
Open Inward
LHRB
Left Hand
Reverse Bevel
Hinges Left
Open Outward
RH
Right Hand
Hinges Right
Open Inward
RHRB
Right Hand
Reverse Bevel
Hinges Right
Open Outward
Prior to installation, all holes must be free of burrs, debris and sharp edges.
If doors are not properly reinforced per ANSI 115.2, commercially available reinforcements should be installed.
Prepare door according to appropriate template:
• Field template A7949 (or wood doors).
• Manufacturer’s template 4629 (for metal doors).
Mortise
pocket
Turn lever hole
Through-bolt
holes
Controller
cutout
Cylinder
hole
Lever
handle
holes
Outside of door Inside of door
Through-bolt
holes
Backplate
mount holes
Lever handle holes
Controller cutout
bDoor Preparation
Figure 6A

8
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
The lock body sticker states the following:
1. Ensure the handing is correct. (To change handing, see
Installation Instructions - Change Hand of Lock Body.)
2. Insert lock body in door.
3. Press wire harness through sticker.
1. Peel back the sticker that covers the retaining
ring and remove the retaining ring.
2. Orient the plastic retaining ring so that the
word BOTTOM is located at the bottom of the
cylinder hole (Figure 7A1).
3. Route the wires from the top of the cylinder
hole into the slot on the top of the plastic
retaining ring, NOT through the retaining ring
(Figure 7A2) and insert the retaining ring into
the non-cylinder side of the cylinder hole.
4. The cable and connector must be coiled inside
retaining ring before inserting mortise into door
prep pocket (Figure 7A2). Make sure the plastic
retaining ring is seated correctly.
Installation Instructions - Door Preparation
6
NOTE: Lock body is shipped with a removable perforated
sticker covering the retaining ring on the non-cylinder side
(inside of door) of the lock body.
Cables and connectors are coiled inside the retaining ring.
• If the handing of the lock body does not need to be
changed, skip 2 and proceed to 3.
cPrepare Lock Body
Perforated
Sticker
Slot
Plastic
Retaining Ring
Inside of Door
(non-cylinder side)
Installation Instructions - Change Hand of Lock Body
7
aRetaining Ring
Harness must be coiled
inside Plastic Retaining Ring
Figure 7A1 Figure 7A2

9
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
bReverse Lock Hand
Installation Instructions - Change Hand of Lock Body, continued
7
Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Figure 7B):
1. Position lock body with red surface of locking piece visible.
2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.
3. Rotate the locking piece 180° until RED surface is on opposite side.
Note: Red indicates locked side (outside). Wire harness MUST exit through the non-cylinder side (inside) of the
lock body (Figure 7C).
Locking Slide
Red on Locked Side
Push In
Right Hand
Lock Shown
Red Locking Piece
Indicates Locked Side
cReverse Latch Hand
Beveled surface of latchbolt must face strike (Figure 7C1).
The deadlatch is self adjusting.
To change the hand of the latchbolt:
1. Insert the blade of a slotted screwdriver (>1/4") into
the spade shape slot behind latch.
2. Rotate the screwdriver 90° to push latchbolt out
until back of bolt clears lock case front.
3. Rotate latchbolt 180° until the latchbolt drops back
into the lock body.
Note: Latch cannot be unscrewed.
Latchbolt
Spade
Shaped
Slot
Deadlatch
Figure 7B
Figure 7C

10
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
Installation Instructions - Installation of Lock Body
8
1. Insert lock body into mortised cutout (Figure 8).
2. Connector and wires must be coiled within
retaining ring in cylinder hole.
3. Push cable and connector through perforated
sticker* on non-cylinder side of hole.
*Note: If hand of lock body has changed, sticker will
have been removed (see previous 2).
4. Hold lock body loosely in place with (2) lock
body screws.
Note: Do not completely tighten screws at this
time.
Mortise lock body
connector and
grounding lug
(2) #12-24 x 1/2"
Flat Head Screws
(Metal Doors)
(2) #12 x 1-1/4”
Flat Head Screws
(Metal Doors)
Installation Instructions - Installation of Outside & Inside Lever
Assembly Lock Body
9
Align through bolt posts on outside lever assembly with door prepped holes (Figure 9).
Mortise Lock Body
Connector and Ground Ring
Terminal
Inside Adapter Plate
Rose
Set Screw
Outside Lever
Assembly
Figure 8
Figure 9
1. Slide the outside lever assembly with
spindle though the door and lock
body.
2. Secure lever assembly with the inside
adapter plate with (2) screws:
DO NOT TIGHTEN.
3. Securely tighten the lock body
screws on edge of door.
4. Securely tighten both inside adapter
screws.
5. Place rose over inside adapter and
tighten clockwise.
6. Fasten inside lever to inside adapter
and tighten lever set screw snugly.

11
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
Installation Instructions - Installation of Cylinder
10
Note: For proper cylinder/parts orientation see Figure
10A. Slide cylinder through the spring and rosette/
collar and screw into lockbody, rotating the cylinder
clockwise.
Cylinder should be flush with rosette/collar.
Note: SARGENT logo must be horizontal and on the
top of the cylinder (Figure 10B).
1. Secure the cylinder by tightening cylinder clamp
screw located above the deadbolt.
2. Using the key, verify that the key retracts the
latchbolt (and deadbolt).
Rosette must
be oriented as
shown
Align cylinder groove
with tapped hole, then
tighten set screw to
hold lock cylinder
Position cylinder so that the SARGENT
logo is right-side up.
Correct Incorrect
Installation Instructions - Deadbolt Functions Only (82276 & 82277)
11
Back Plate
#6 x 3/8" Round Head
Wood Screws
#6-32 x 3/8" Round
Head Machine Screws
#6-32 x 1/4"
Flat Head Screw
Thumb Turn
Alignment Tool
1. Insert alignment tool (supplied) into lock body thumb
turn.
2. Slide back plate over tool and make level.
3. Secure back plate to door with two (2) #6 x 3/8" round
head wood screws or #6-32 x 3/8” round head machine
screws.
4. Dispose of tool, position thumb turn over back plate
(Figure 11) and secure with #6-32 x 1/4" flat head screw.
Note: Thumb turn should cover screw head when deadbolt is
retracted.
5. Refer to instructions (A5675G) included in package
included with lock.
Figure 10B Figure 10A
Figure 11 Detail Figure 11

12
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
Installation Instructions - Gasket Installation (Optional)
12
Installation Instructions - Installation of Outside Escutcheon and Mounting
Plate Assembly
13
Note: Optional, for non-fire rated doors only.
For non-fire rated door applications, an optional gasket (Figure 12) may be used as a weather seal between the
escutcheon and the outside door surface.
Peel off adhesive
backing and attach to
(outside) escutcheon
1. Insert the mounting posts through holes as shown.
2. On the inside of the door, position the mounting plate over the indicated holes.
Note: Feed controller and keypad cables through side opening (Figure 13A).
Mounting Plate
Cables
Position lug upright, then
tighten screw
Figure 12
Figure 13A

13
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
Inside of door Mounting
plate
(4) #8 - 32 x 1 - 7/8" flat
head machine screws
Attach ground
lug to bottom
right screw
Outside
Passport
Trim
(2) #8 - 3/8"
flat head
wood
screws or
(2) #8 - 3/8" flat
head machine
screws
Inside of door
Installation Instructions - Installation of Outside Escutcheon and Mounting
Plate Assembly, continued
13
Installation Instructions - Installation of Inside Component Assembly
14
Cable from lock body feeds thru bottom (Figure 13A and 13B).
3. Attach grounding lug to bottom right screw and note upright positioning of lug as shown (Figure 13B).
4. Insert other three corner screws and tighten, fastening the outside escutcheon to the door (Figure 13B).
IMPORTANT: If the following step is skipped, the product will not be UL-compliant:
5. Attach two (2) #8 x 3/8" flat head wood screws for wood doors, or (2) #8-32 x 3/8" flat head machine screws
for metal doors (Figure 13C).
Insert bottom of component assembly first (Figure 14), then clip top of component assembly to backplate,
verifying both tabs attached securely.
Inside of door
Figure 13B Figure 13C
Figure 14

14
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
Installation Instructions - Installation of Connectors
15
Installation Instructions - Battery / Battery Pack Installation and DIP Switch
Setting Verification
16
Secure the following
connectors onto the circuit
board (Figure 15 and Detail):
Note: Connectors go on only
one way. Do not force and do
not offset connectors.
Be sure they are completely
seated (flush).
1. Secure the mortise lock
body assembly connector
(10-pin).
2. Secure the mortise keypad/
card reader connector
(14-pin).
3. Secure the LCU connector
(7-pin).
From outside trim
(ground)
Detail
From outside trim
(card reader)
From outside
trim (keypad)
From lock body
1. Place (6) “AA” batteries into the compartment being careful to
align polarity (- & +) properly.
2. Insert battery pack and click into place, making sure polarity
terminals on the battery pack are oriented upwards (Figure 16).
3. Verify DIP switch settings are correct for the application.
PERSONA PG
controller DIP
switch location
PERSONA PG Controller DIP
Switch Settings (Fig 10A):
ON
OFF
ON
OFF
SARGENT mortise lock with and
without deadbolt:
• Switch 1 and 2 - OFF
• Switch 3 - ON
SARGENT cylinder or exit locks:
• Switch 1 - OFF
• Switch 2 and 3 - ON
Figure 15 Detail
Figure 15
Figure 16

15
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
Installation Instructions - Installation of Inside Escutcheon
17
Installation Instructions - Application of Front Plate
18
1. Position inside escutcheon.
2. Insert screws, top and bottom, and tighten securely.
DO NOT OVERTIGHTEN.
Note: All wires should be placed inside to avoid being pinched.
3. Straighten escutcheon and tighten securely.
Attach front plate with (2) #8-32 X 1/4" flat head screws.

16
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
Setting up the LockLink™ and Contact Card for First Use*
19
*NOTE: The following steps in this section are only performed one time. Once Bluetooth pairing is complete,
these steps do not need to be repeated to program locks (Section 8 ”Lockset Programming”)
aPairing the Pocket PC with the Contact Card
1. To begin, highlight (by tapping) the
button and select the ‘Settings’
menu.
2. Next, tap the ‘Connections’ tab at the
bottom of the screen and highlight the
Bluetooth icon from the ‘Settings’
menu.
4. The Pocket PC will enable Bluetooth and begin discovery. If you receive a warning, “No Devices Found,” then
check again to see the blue light flashing on the Contact Card and tap ‘Retry’.
• If the blue light is not flashing, remove the Contact Card, wait for the lights to go dark, then reinsert it
before tapping ‘Retry’.
• If this step fails repeatedly, then contact PERSONA technical support at (800)–481–8464.
Contact Card
3. Insert the Contact Card into a lock
(provides power to Contact Card) and
then select “Add New Device...”

17
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
Setting up the LockLink™ and Contact Card for First Use, continued
19
LockSet Programming
20
bConfiguring the LockLink™ Software
1. When the list entry
appears, highlight it and tap ‘Next’.
2. Enter “1234” when prompted for
‘Passcode.’
3. Tap the ‘COM Ports’ tab at the bottom of
the screen. Note the COM port number
assigned to the Firefly device.
NOTE: If you do not see the FireFly-EAE0 device
in the COM port list, tap ‘New Outgoing Port’
and pick the FireFly-EAE0 device before tapping
‘Next’.
4. Choose an available COM port number
(COM8 is often a good choice) and tap
’Finish.”
1. Tap then tap
to launch the LockLink program.
2. Choose Menu and then ‘Setup’.
3. Select the COM port noted in Step 3 of
Section 20b.
4. Check the ‘Use Bluetooth’ box and tap
‘Apply’.

18
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
1. Tap on the Pocket PC Screen.
2. If visible, select PERSONA LockLink™ to launch
the program; otherwise, tap Start and Programs
to launch the Programs list and then select the
PERSONA LockLink™ icon (right).
3. Log into the LockLink™ by tapping the arrow and
selecting your username from the drop down list:
LockSet Programming, continued
20
aStart the PERSONA LockLink™ Software
4. Type in your password. You can use the onscreen keyboard entry method to
enter information.
5. To access the full screen keyboard (shown at right) tap on the ellipsis
(three dots) next to the password field.
Once you have entered your password, you will begin on the Upload screen.
This is the proper place to be for programming locks.
Note: Be sure to perform an Operational Check (see Section 9) for each lock.
bUpload Full Program
After locks are installed, they must have program files copied into them before they can receive and interpret
data. In many ways, the program files act as the locks’ operating system by interpreting the lock data to control
each lock’s behavior.
1. Highlight (by tapping) the name of the lock
that you wish to program.
If the list of locks is longer than the display,
locate the lock using the scroll bar at the
right of the display or use the button
at the top of the display.
2. Tap the button to completely
initialize the lock; the message ”Alert! Make
sure the Contact Card is Inserted or has
power.”
3. Tap “ok.”

19
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
A7807D 12/22
Passport 1000 PG
Mortise Lock
LockSet Programming, continued
20
4. Follow the directions on the screen.
NOTE: You will be prompted to insert the Contact Card into the lock three times.
5. When the data has finished loading, you are notified to remove the Contact Card from the lock.
bUpload Full Program, continued
6. Reinsert Contact Card a second time to
initialize the program.
Note: You should hear the motor run briefly.

20
1-800-727-5477 • www.sargentlock.com A7807D 12/22
Passport 1000 PG
Mortise Lock
Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved.
Reproduction in whole or in part without the express written permission of SARGENT Manufacturing
Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
7. Program initializes and directs you to
remove the Contact Card.
LockSet Programming, continued
20
bUpload Full Program, continued
9. Remove the Contact Card.
10. To exit and return to the program screen,
tap the button.
8. Follow the on-screen directions and
reinsert the Contact Card a third time.