Assa Abloy Sargent PE80 Series User manual

1-800-727-5477 • www.sargentlock.com
Installation Instructions
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written
permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in damage
to the product and void the factory
warranty.
WARNING
Cylinder Dogging
PE80 Series Exit Devices
A8318-1 5/23
Cylinder
Insert
Cylinder Insert View
Hex Key Dogging Scalp Blank Scalp
Cylinder nut

2
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Cylinder Dogging
Installation Instructions
PE80 Series Exit Devices
A8318-1 05/23
1
Remove rail mount.
2
Remove four #6 screws to remove dogging slope assembly.
Dogging slope assembly
Dogging cam
#6 Screws
Dogging spring

3
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Cylinder Dogging
Installation Instructions
PE80 Series Exit Devices
A8318-1 05/23
6
34
Remove two #4 screws. Rotate and extract scalp.
Install two #4 screws.
5
Dogging
slope
Blank
Scalp
#4
Screws
Dogging slope
Scalp
#4
Screws
Install the new scalp.

4
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Cylinder Dogging
Installation Instructions
PE80 Series Exit Devices
A8318-1 05/23
Place dogging cam in carrier hole.
8
7
Place dogging spring outside of dogging slope.
Insert both on the carrier. Install four #6 screws.
Dogging
cam
Carrier Carrier
#6 Screws
Dogging spring
Dogging slope

5
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Cylinder Dogging
Installation Instructions
PE80 Series Exit Devices
A8318-1 05/23
11
B
A
A
B
910
12
Slide carrier into rail mount. Slide dogging insert into rail mount.
Test the function by (A) compressing the bar, and (B)
turning the key clockwise to engage dogging. The bar
should stay compressed.
Test the function by (A) turning the key counter-
clockwise to release dogging. (B) The bar should
return to the uncompressed position on its own.
Rail mount
Carrier Dogging Insert

6
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Cylinder Dogging
Installation Instructions
PE80 Series Exit Devices
A8318-1 05/23

7
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Cylinder Dogging
Installation Instructions
PE80 Series Exit Devices
A8318-1 05/23

1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written
permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents. A8318-1 5/23