Assa Abloy Sargent 8200 Series User manual

A8260C 03/20
Installation Instructions
1-800-727-5477 • www.sargentlock.com
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
Copyright© 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
7800 and 8200
Series Mortise Lock
Used with VN1 Escutcheon Trim and
V Series Indicators

2
7800 and 8200 Series Mortise Locks
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
A8260C 03/20
Copyright© 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
1 Tools Required
#2 & #3 Phillips
head screwdrivers
Flat blade
screwdriver
1/8”Allen Wrench 3/8"Drill bit T-20 Torx Screw with
Tamper Pin Driver
TOC Table of Contents
1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2 Indicator Variants. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3 Lock set configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
4 Rehanding Indicator (if required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
a Prepare Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
b Install Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
c Install Outside Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
d Install Inside Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
e Install Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
f Install Outside Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
g Perform Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
6 Indicator Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3
7800 and 8200 Series Mortise Locks
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
A8260C 03/20
Copyright© 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
2 Indicator Variants
Depending on function and option ordered,
indicators are provided in the following variations,
these instructions detail how to install with
cylinder, however other variations follow similar
instructions. (Figure1)
• Contact factory with questions.
Coin Turn - For
installation on
outside of door.
Cylinder - For
installation on
inside or outside
of door.
No input / blank
-For installation
on inside or
outside of door.
Thumbturn - For
installation on
inside of door.
Figure1
3 Lock set configuration
To set function of multi-function lock or to re-hand, see instructions on lock body.
4 Rehanding Indicator (if required)
Verify hand and bevel of door. (Figure2)
LH
Left Hand
Hinges Left
Open Inward
RH
Right Hand
Hinges Right
Open Inward
LHRB
Left Hand
Reverse Bevel
Hinges Left
Open Outward
RHRB
Right Hand
Reverse Bevel
Hinges Right
Open Outward
Figure2
Note:
Stand outside of locked door when determining door hand.
Next, verify inside and/or outside indicators are handed
correctly, using Spindle Cam Position chart. (Figure3)
If they are handed correctly, skip to Step 5 "Prepare Door".
If they are not handed correctly:
1. Remove indicator back plate by pulling out from top slot,
then remove spindle cam from assembly. (Figure4)
2. Position spindle cam in correct direction for door
hand. (Figure3)
Important:
• For thumbturn indicators, make sure thumbturn is
positioned in 12 o’clock direction as shown. (Figure5)
3. Slide spindle cam post into the correct slot of the
display slide. (Figure4)
4. Re-seat back plate into original position.
5. Return indicator to vacant/unlocked position for installation.
Door Hand: RH / RHRB
Door Hand: LH / LHRB
Outside Indicator
Inside Indicator
Inside Indicator
Outside Indicator
Spindle Cam Position for Locks with Deadbolt (*and 56 function)
Door Hand: RH / RHRB
Door Hand: LH / LHRB
Outside Indicator
Inside Indicator
Inside Indicator
Outside Indicator
Spindle Cam Position for Locks without Deadbolt (*except 56 function)
Figure3
Figure4
Spindle
cam
Display
slide slot
Plate slot
for removal
Back plate
Thumbturn
position
Figure5

4
7800 and 8200 Series Mortise Locks
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
A8260C 03/20
Copyright© 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
5 Installation
a Prepare Door
Prepare door for function holes, size, and location according to A8258
door marker template, if not already prepped.
b Install Lock
1. Verify strike location according to template. Clean out door pocket
and door edge of debris.
2. Ensure handing of lock and door match. Slide lock into door. (Figure6)
3. Temporarily hand tighten two (2) lock screws (#12 x 1-1/4"
wood screws, or #12-24x 1/2"machine screws).
Note:
Keep door open until installation is complete.
c Install Outside Trim
1. Verify lock is in unlocked state (control hub slot should be vertical).
Also, verify indicator is in vacant/unlocked position.
2. Align trim posts with diagonal holes in door, be sure lever is horizontal. Slide outside escutcheon
assembly through lock body from outside door face. (Figure7)
Note:
If indicator is used on outside, align indicator spindle with control hub.
d Install Inside Trim
1. Slide spindle into lockbody hub. (Figure8)
2. Slide adapter and plate assembly over spindle.
3. Secure with two (2) #8-32 x 5/8" screws.
4. For Studio Collection levers only, use trim bushing over adapter plate.
5. Verify lock is in unlocked state (turn outside lever to ensure).
Also, Verify indicator is in vacant/unlocked position.
6. Align escutcheon over adapter and install inside
escutcheon assembly onto inside door face.
Notes:
• If indicator is used on inside, align indicator
spindle with control hub.
7. Through-bolt inside escutcheon to outside
escutcheon with two (2) #8-32 x 2-1/4"screws.
8. Install inside lever on adapter plate.
Secure with set screw.
Note:
Screw heads should be visible on inside escutcheon.
Inside of door
Lock
Lock
Screws
Outside
of door
RH door
shown
Figure6
Outside Escutcheon Assembly
Figure7
Figure8
Inside
Escutcheon
Assembly
Studio
Collection
Trim
Bushing
Adapter Plate
Spindle
Lever
Set
screw
#8-32 x 2-1/4" screw
#8-32 x
2-1/4"
screw
#8-32 x
5/8" screws

5
7800 and 8200 Series Mortise Locks
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
A8260C 03/20
Copyright© 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
5 Installation (cont.)
e Install Cylinder
1. Thread cylinder into lock until flush with escutcheon
surface. (Figure9)
• Pull key slightly out of cylinder to help thread into
lock body.
2. Tighten cylinder clamp screw with #1 Phillips screwdriver.
• Check operation and adjust cylinder if necessary.
Notes:
• SARGENT logo must be horizontal and on top. (Figure10)
• If double cylinder function is used, repeat steps 1 and 2
for second cylinder.
• Removable Core or Interchangeable Core cylinders require
a control key (key stamped with C) to remove and install
the core. This is not provided standard; it must be
requested separately. If requesting 1-bitted control key,
specify 113511 cut.
f Install Outside Front
1. Tighten the two (2) lock screws completely. (Figure11)
2. Attach outside front with two (2) flat head screws
#8-32 x 1/4".
g Perform Functional Check
DO NOT FORCE if resistance is encountered during functional check.
Refer back to Rehanding Indicator (if required) section to ensure
correct handing. Rehand if necessary.
1. Insert key into cylinder (if present) and rotate:
• Ensure there is no friction against lock case or
any other obstructions.
2. Check key retracts latch:
• Key should rotate freely.
3. Throw deadbolt (if present):
• Check key retracts both deadbolt and latch.
4. Test levers:
• Confirm latch and deadbolt (if installed) retract.
5. Verify indicator displays correct status when locked
and unlocked.
Cylinder
Cylinder
Clamp
Screw
Figure9
Incorrect
Key and cylinder must be rotated as shown.
Correct
Figure10
Figure11
Lock
screw
Outside
front
Lock screw
#8-32 x
1/4" screws

6
7800 and 8200 Series Mortise Locks
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
A8260C 03/20
Copyright© 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
6 Indicator Parts List
4A
4B
4C
Figure12
Figure12 Description Part Number Req.
1 VN1 Indicator Escutcheon Consult Factory 1
2 Indicator Window 81-0811 1
3
Indicator Display Assembly - Green Unlocked / Red Locked 82-5602
1
Indicator Display Assembly - Green Vacant / Red Occupied 82-5603
Indicator Display Assembly - Green Unlocked Icon / Red Locked Icon 82-5604
Indicator Display Assembly - White Unlocked / Red Locked 82-5605
Indicator Display Assembly - White Vacant / Red Occupied 82-5606
Indicator Display Assembly - White Unlocked Icon / Red Locked Icon 82-5607
4A Indicator Spindle Cam - Thumbturn / Coin Turn 81-0745 1
4B Indicator Spindle Cam - Cylinder / No Input / Blank 81-0756* 1
4C Indicator Spindle Cam - 05, 37, 38, 59 Functions 81-5577* 1
5 Indicator Backing Plate 81-0748 1
6 VN1 Escutcheon Screw Pack (Not shown) 82-5587 x finish* 1
7 Door Marker Template (Not shown) A8258 1
* These parts are for 1-3/4"standard thickness doors. For other thicknesses, please contact factory.
Note:
Reference 8200 Series parts manual for all lock body parts.

7
7800 and 8200 Series Mortise Locks
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
A8260C 03/20
Copyright© 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com

A8260C 03/20
Founded in the early 1800s, SARGENT®is a market leader in locksets, cylinders, door closers, exit devices, electro-
mechanical products and access control systems for new construction, renovation, and replacement applications.
The company’s customer base includes commercial construction, institutional, and industrial markets.
SARGENT is a brand associated with ASSA ABLOY High Security Group, Inc., an ASSA ABLOY Access and Egress
Hardware Group company. Copyright© 2019,2020, ASSA ABLOY Access and Egress Hardware Group, Inc. All
rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Access
and Egress Hardware Group, Inc. is prohibited.
SARGENT Manufacturing Company
100 Sargent Drive
New Haven, CT 06511 USA
800-727-5477
www.sargentlock.com