Assa Abloy Securitron Magnalock Series User manual

Securitron Magnalock Corp. Tel [phone]
550 Vista Boulevard Fax [phone]
Sparks, NV 89434 [email protected]
www.securitron.com
© Copyright, 2008, all rights reserved PN# 500-10420
Page 1 Rev. E, 05/08
ASSA ABLOY, the global leader
in door opening solutions
MAGNALOCK MODELS M32, M62 AND M82B
INSTALLATION INSTRUCTIONS
1. INTRODUCTION
The Securitron Magnalock family represents the state of the art in electromagnetic locking.
There are three (3) models with operational electrical characteristics including mounting
configuration options addressed in this manual.
The BondSTAT “B” Magnalock Series, Bond Sensor, monitors the magnetic field. An internal
sensor activates a SPDT dry contact relay connection designed for interface to access control
and/or alarm systems for reporting the status of the Magnalock. (Section 5.2.4)
The DPS “D” Magnalock Series, Door Position Sensor, is activated by a special magnetic strike
armature assembly. The isolated SPDT reed switch, with an internal resettable protection device,
is designed for interface to access control and/or alarm system for door status. (Section 5.2.4)
2. SPECIFICATIONS
MODEL M32 M62 M82B
Holding Force 600 Lbs [272 kg] 1200 Lbs [544 kg] 1800 Lbs [816 kg]
Dimensions: Length 8" [203mm] 8" [203mm] 12" [305mm]
Height 1.88" [48mm] 3" [76mm] 3" [76mm]
Depth 1.6" [41mm] 1.75" [44mm] 1.75" [44mm]
Dual Voltage 12/24 Volts DC
Current: @ 12 VDC 300mA 250mA 350mA
@ 24 VDC 150mA 150mA 200mA
Capacitance: @ 12 VDC 6.8 mF 44 mF 44 mF
@ 24 VDC 6.8 mF 11 mF 11 mF
BondSTAT Rating Voltage: 30 VDC (Maximum) ~ Current: 1 Amp (Maximum)
DPS Rating Voltage: 30 VDC (Maximum) ~ Current: 125 mA (Maximum)
3. PRODUCT OVERVIEW
Upon unpacking this product, an inventory should be made to ensure that all the required
components and hardware have been included. Along with these instructions and the
installation template, the lock assembly should include the following items:
Figure 1
Magnalock Sex Bolt
Strike Plate Hardware Pack

PN# 500-10420
Page 2 Rev. E, 05/08
4. RECOMMENDED TOOLS
Power Drill Hammer Wire Strippers/Cutter
1/8”, 3/8”, 1/2” Drill Bits Center Punch Crimp Wire Connectors
1/2” Open end or Crescent Wrench Masking Tape Crimp Tool
3/16” Hex Key (Allen Wrench) Fish Tape or Lead Wire Multimeter
5. INSTALLATION INSTRUCTIONS
5.1 Pre-Installation Survey
It is recommended that an initial on sight survey be performed. A method of mounting should
be determined and an installation plan should be reviewed as follows:
xPhysical strength of mounting areas should be strong enough to meet or exceed the
holding force of the required Magnalock.
xPlacement of the Magnalock wiring and protection from potential damage due to intruders
or vandals external attack should be considered during the survey.
xAccessibility should be considered for prevention of any potential safety hazard.
Additional brackets may be needed for proper installation. Specialized brackets are available
through Securitron and their many product distributors. (Section 6)
5.2 Out-Swinging Door
The installation shown below in Figure 2 illustrates the door swinging away from the Magnalock.
This is a common configuration on the secure side of exit doors. The Magnalock mounts to the
door frame header near the corner opposite the hinge side. The Magnalock may be mounted
horizontally or vertically depending on the installation required. The brackets shown in Figure 2
are to assist installation to door frames that may need modifications to complete the installation.
Figure 2
Dress Plugs
Mountin
g
Screws
Sex Bolt & Strike
Mounting Screw
Door Frame & Stop
Rubber Washers
Door
Strike Plate
Flat Washers
Blind Nuts
Magnalock
UHB Bracket
SFP Bracket
M32 ~ 2-1/4”
M62 ~ 2-1/2”
M82 ~ 2-1/2”

PN# 500-10420
Page 3 Rev. E, 05/08
5.2.1 Mounting the Strike Plate
The strike plate should be mounted prior to the magnet in out-swinging door applications.
Figure 3 below illustrates a typical strike mounting configuration.
Figure 3
Select a mounting location for the Magnalock and strike assembly as mentioned in Section 5.1.
The following general guideline should be used for consideration during the installation review:
xRead and follow the template instructions which include drilling and mounting instructions.
xInstalling a strike plate horizontally, the top edge of the strike will be approximately 1/8"
[3.2mm] below the door frame stop. If the strike and magnet are to be mounted
vertically, increase this clearance between the strike and frame to 3/16" [4.8mm].
xAn approximated 1” [25.4mm] clearance should be considered between the Magnalock
and the edge corner of the door frame. This will allow proper access for the mounting
locations for drilling and tool access.
xUse the template provided for positioning and marking the mounting locations of the
Magnalock and strike. Check the external and internal areas of the marked door and
frame for any obstacles such as wire chases or internal structural features. Make
necessary adjustments to avoid these obstacles.
xOffset strikes are available for lowering a strike alignment 1/4” [6.0mm] allowing
clearance when door construction contains obstructions in the mounting locations.
5.2.2 Mounting the Magnet
Installations with blade stops require an Aluminum Spacer Bracket (ASB) for clearance without
having to cut the stop as shown in Figure 4. Information on mounting brackets is located in
Section 6 of this manual.
To properly install the Magnalock, the following conditions should be verified:
xThe entire Magnalock mounting area for the magnet must be a flat surface.
xThe frame area selected must be structurally strong enough for support.
xThe magnet face must be mounted parallel to the door face when closed.
xThe installed strike must still allow the door to close properly by clearance and alignment.
xThe Magnalock face and strike plate must be aligned so that they are centered.
ALIGNMENT IS IMPORTANT FOR “B” & “D” MAGNALOCKS (Section 5.2.4)
ALIGNMENT IS CRITICAL FOR THE MAGNALOCK HOLDING FORCE (Section 2)
xMark and drill all holes for the mounting screws as instructed on the template.
xMake wire connections, apply power and test for proper operation.
xMount the Magnalock using the hardware and thread locking compound provided.
xTighten the screws until secure.
DO NOT OVER-TIGHTEN SCREWS
NEVER DRILL MAGNALOCK MOUNTING HOLES
– DAMAGE MAY OCCUR –
Strike Plate
2-3 Washers
2X Roll Pins
Strike Mounting
Screw
Strike Bushing
2X Roll Pin Bushings
Door Frame & Stop
Sex Bolt

PN# 500-10420
Page 4 Rev. E, 05/08
Figure 4 below illustrates a typical Magnalock out-swinging door installation.
Figure 4
Blind nuts MUST be used for mounting Magnalocks to aluminum and/or hollow metal frames.
These items are included with the Magnalock hardware pack.
NEVER USE SHEET METAL SCREWS TO MOUNT MAGNALOCKS
5.2.3 Blind Nut Installation
Install a blind nut into each of the 3/8” [9.5mm] hole using the blind nut collapsing tool
provided. Use the following instructions and Figure 5 for the installation of the blind nuts:
xDrill 3/8” [9.5mm] diameter mounting holes into the marked locations of the frame.
xInsert the assembled Blind Nut and Installation Tool into a mounting hole.
xUse 1/2” [13mm] box-end wrench for holding the Install Nut.
xUse a 3/16” [5.0mm] Hex Wrench with the Socket Cap Screw to collapse the Blind Nut.
xRemove the collapsing tool when finished.
xCheck that the blind nut is collapsed properly.
xThe collapsing tool is reusable for several blind nut installations.
Figure 5
Blind Nuts
Magnalock
Mounting Hole
Dress Plugs
ASB Bracket
(
Not Included
)
Mounting
Screws
Door Frame & Stop
Flat Washers
Blind Nut
2X Flat Washers Socket Cap Screw
Install Nut

PN# 500-10420
Page 5 Rev. E, 05/08
5.2.4 Lock/Strike Installation for “B” and “D” Magnalocks
IMPORTANT!
PLEASE READ AND APPLY THIS INFORMATION WHEN ALIGNING/INSTALLING THE
LOCK AND STRIKE. THE ALIGNMENT TOLERANCES INDICATED FOR EACH LOCK
MODEL ARE CONSIDERED CRITICAL FOR THE PROPER OPERATION OF BOTH THE
MAGNETIC BOND SENSING AND DOOR POSITION SENSING SYSTEMS!
SENSOR RANGES (PHYSICAL POSITIONING):
The BondSTAT “B” and DPS “D” Magnalock “Secure Zone” sensing ranges for each lock
model is listed in Table A.
(The Figure 6 illustration is a visual reference to the sensing ranges outlined in Table A).
Secure Sensor Indication Range
(Dimensions from Center)
Model "X" (+/-) "Y" (+/-)
M32B/D 9/32" 1/8"
M62B/D 5/16" 1/8"
M82B/D 9/16" 1/8"
Table A
(+)
(+)
(-)
(+)
(-)
(-)
(+)
(-)
X
Y
0
0
Figure 6
5.2.5 In-swinging Door Installation
Figure 7 below illustrates a typical in-swinging door mounting configuration. This installation
requires the use of a face mount style Magnalock (i.e. M32F, M62F, or M82FB) and a “Z” bracket
(Z-32, Z-62, or Z-82) or an adjustable “ZA” bracket (ZA-32/62 or ZA-82) for offsetting the
mounting of the strike must be used. Follow the installation instructions provided with the “Z” or
“ZA” bracket product to correctly install the Magnalock in this arrangement.
THE M62F AND M82FB INCLUDE FIVE (5) MOUNTING HOLES FOR FLEXIBILITY
Figure 7
Z-Bracket or “ZA Bracket
(Dress cover not shown)
Strike Plate
Magnalock
Blind Nuts
and Mounting
Screws
Strike Mounting
Hardware and
T-Nut
Sex Bolt
Door Frame and Stop
Door
Bracket Mounting
Hardware

PN# 500-10420
Page 6 Rev. E, 05/08
5.2.5 Single Lock - Double Door Magnalock Mounting
A single Magnalock can be used to secure double doors using a split strike plate. The part
numbers reduction of holding force for each model is listed below in Table B. Use the template
and instructions provided with the split strike package for proper installation. (See Section 7)
Table B
5.2.6 DM62 Double 62 Magnalock
The DM62 consists of two (2) Model 62 Magnalocks arranged in one (1) stainless steel housing
as shown in Figure 8. This product individually secures out-swinging double door applications.
Figure 8
Use the template diagram installation instructions included with the DM62 Magnalock assembly.
The features to consideration during the installation procedure:
xPosition the Magnalock centered between the doors.
xThe mounting diagram measurement and marking placement are critical.
xThe mounting diagram is NOT a scaled template.
xRefer to the Magnalock out-swinging door mounting procedures in Section: 5.2.
xRefer to the strike mounting procedures in Section: 5.2.1.
xRefer to the blind nut instructions in Section: 5.2.3.
5.2.7 Mounting Magnalocks for Gates
The “G” Series Magnalock is suitable for use on outdoor gates. Figure 9 illustrates a variety of
typical gate operations for application types and installation techniques. Special mounting
brackets are available. See Section 6.2 for gate bracket information.
IMPORTANT
THE STRIKE PLATE SHOULD NOT BE WELDED DIRECTLY TO THE GATE
THE STRIKE MUST BE MOUNTED USING THE HARDWARE PROVIDED
HOLDING FORCE AND ALIGNMENT WILL OTHERWISE BE AFFECTED
Model Offset Strike
Part Number
Split Strike
Part Number
Holding Force
(per leaf)
M32 N/A ASS-32 230 lbs. [104 kg]
M62 AOS-62 ASS-62 550 lbs. [250 kg]
M82 AOS-82 ASS-82 850 lbs. [385 kg]

PN# 500-10420
Page 7 Rev. E, 05/08
GATE STYLE OPERATIONS AND INSTALLATION TECHNIQUES
Figure 9
5.3 ELECTRICAL INSTALLATION
5.3.1 General Characteristics
The Magnalock is a low current load device using specialized internal circuitry. The normal
characteristic of an inductive load, such as inductive kick-back, is not present. See Section 2 for
more information.
5.3.2 Electrical Standards
DC voltage, full-wave rectified, must be provided for proper operation of the Magnalocks. The
red wire receives +12VDC or +24VDC, and the black wire, 0 Volts (negative). If the lock is
connected with reverse polarity, it will not operate. The M32, M62 and M82B Magnalocks are
auto sensing dual voltage locks. The Magnalock circuit design will automatically select the proper
operational conditions for the applied voltage. See Section 2 for more information.
5.3.3 Poor Release Characteristics
The Magnalock is designed with quick release circuitry. Wiring errors may cause a Magnalocks to
release slowly. Figure 10 illustrates a parallel installation of a resistive load (correct). Figure
11 illustrates a parallel reverse diode (incorrect).
Figure 10 Figure 11
5.3.4 Sensor Ranges (ELECTRICAL)
The “B” version monitoring system is also voltage sensitive. The specified voltage ranges must
be properly applied. Refer to Section 2 for the recommended operating voltage ranges.

PN# 500-10420
Page 8 Rev. E, 05/08
5.3.5 Electrical Wiring
The following diagrams, Figures 12,13, 14 and 15 represent the proper electrical wiring
connections required for Magnalock Standard, BondSTAT “B”, DPS “D” and “BD” versions.
Figure 12
Figure 13
Figure 14
Figure 15

PN# 500-10420
Page 9 Rev. E, 05/08
5.3.6 BondSTAT Sensor status wiring description
xThe green and white wires supply electrical connection when the lock is ON and secure.
xThe orange and white wires supply electrical connection when the lock OFF or unsecure.
5.3.7 DPS – Door Position Sensor status wiring description
xThe blue and yellow wires supply electrical connection when the door condition is closed.
xThe brown and yellow wires supply electrical connection when the door condition is open.
5.3.8 Double Door Status Wiring – BondSTAT
When two Magnalocks are used for double door installation the BondSTAT contacts should be
wired in series for proper reporting. Connect the green wire of one lock to the white wire of the
other as shown below in Figure 16.
Figure 16
5.3.9 Double Door Status Wiring – DPS
When two Magnalocks are used for double door installation the DPS contacts should be wired in
series for proper reporting. Connect the blue wire of one lock to the yellow wire of the other as
shown below in Figure 17.
Figure 17
5.3.10 Emergency Release
Magnalocks are often wired into a system for quick release in case of emergency. Manual
switching or automatic triggering from a fire alarm system is practical. It is the user's
responsibility to correctly hookup the Magnalock according to the instructions. It is
recommended to use a switch or relay to perform break of power. Securitron power supplies
have terminals for the interconnection of such emergency release switches.
THE END USER & INSTALLER ARE LIABLE FOR FIRE & BUILDING CODES COMPLIANCE
6. SPECIALIZED MOUNTING BRACKETS
xASB – Aluminum Shim Bracket – The ASB bracket is designed for 1/2” [12.7mm]
blade stop and/or weather trim clearance mounting of Magnalocks on aluminum frame
glass doors.
xCWB – Concrete/Wood Header Bracket – The CWB bracket is designed for mounting
Magnalocks on concrete filled and/or wood headers.
xFMK-SL & FMK-SW – FLEX-MOUNT Kit – The FMK (FLEX-MOUNT) bracket kits are
designed to install on most gate applications. Adapts to round or square posts from 1”
[25.4mm] to 3” [76.2mm]. The FMK-SL is designed for slide gate type applications. The
FMK-SW is designed for swing gate type applications.
xGDB – Glass Door Bracket – The GDB bracket is designed for mounting a Model 32 or
Model 62 strike to solid-type framed and unframed glass doors. An AKG adhesive kit used
for bonding.
xHEB Bracket – The HEB is a 90 degree bracket designed to extend the door stop and
create a flat surface for mounting the Magnalock.
xHEB-3G Bracket – The HEB-3G bracket is a 90 degree bracket designed for mounting to
solid-type framed and unframed glass headers. An AKG adhesive kit used for bonding.

PN# 500-10420
Page 10 Rev. E, 05/08
xSFP – Stop Filler Plate – The SFP bracket is designed for extending the door frame
mounting surface 1-1/4” [31.8mm]. Thicknesses available in 1/4” [6.4mm], 3/8”
[9.5mm], 1/2” [12.7mm] and 5/8” [15.9mm]. Lengths available in 8” [203mm] for M32
or M62 and 12” [305mm] for M82B Magnalocks.
xUHB – Universal Header Bracket – The UHB bracket is designed to extend the frame
width 1” [25.4mm] to 1-1/2” [38.1mm] deeper on steel and aluminum headers not wide
enough to mount the Magnalock. Lengths available in 8” [203mm] for M32 or M62 and
12” [305mm] for M82B Magnalocks.
xZ-Bracket – The “Z” bracket is designed for use with installations of “F” Series
Magnalocks for in-swinging doors and gates.
xZA-Bracket – The “ZA” bracket is designed to allow a full range of adjustability for use
with installations of “F” Series Magnalocks for in-swinging doors and gates.
7. SPECIALIZED STRIKES
xThe AOS – Armature Offset strike is designed for offset drilling doors with mechanical
interference hardware present in the door structure. It is also accommodates errors that
may have occurred in the field from incorrect mounting placement. (See Section 5.2.5)
xThe ASS – Armature Split strike is designed for single lock/double door installation. There
is a reduced holding force when using the split strike. (See Section 5.2.5)
8. SPECIALIZED ACCESSORIES
8.1 Dress Covers
xSingle Magnalock Dress Covers – The covers are designed to meet architectural
finishes for matching specified installations. Available in four (4) architectural finishes.
xDouble Dress Covers – The covers are designed to fit over a double door/dual lock
installation. Available in two (2) architectural finishes.
8.2 Installation Tool Kit – Securitron offers an installation tool kit which includes special drill
bits, a heavy duty drill guide, a blind nut collapsing tool, extra fasteners and hardware.
Metric is also available.
8.3 Tamper Proofing – Special tamper proof screws are available for Magnalock and strike
armature mounting. The screws are pinned-socket hex head. A special hex wrench is
required and is available when purchasing the screws.
9. MAGNALOCK MAINTENANCE
9.1 Visual Inspection
xCheck the rubber washers for elasticity and proper pivoting. Tighten as required.
xCheck for build-up of debris on the Magnalock and strike armature. Clean as required.
xCheck for rust on the Magnalock and strike plate armature. Clean as required.
9.2 Cleaning Methods
xCleaning once a year is recommended.
xClean every six months where minor rusting occurs.
xClean every three months if rust conditions are severe.
xUse a plastic dishwashing scrub pad to aid in the removal of rust.
DO NOT USE PETROLEUM BASED PRODUCTS FOR CLEANING
DO NOT USE STEEL WOOL BASED SCRUB PAD OR SANDPAPER
9.2.1 Indoor Applications
xApply rubbing alcohol onto a clean cloth and thoroughly wipe down the Magnalock and
strike plate armature.
9.2.2 Outdoor Applications
xApply a silicone based cleaner/lubricant onto a clean cloth and thoroughly wipe down
Magnalock and strike plate armature.
Example: Super Lube® Aerosol with SYNCOLON® (PTFE)
Part No.: 31040 ~ 6oz. / 31110 ~ 11 oz. / 32015 ~ 14 oz.
Phone: [phone] / Website: www.super-lube.com

PN# 500-10420
Page 11 Rev. E, 05/08
APPENDIX A
Troubleshooting
Problem Lock Does Not Generate a Magnetic Field Points of Reference
Check for specified voltage at Magnalock Section 2
Solution Check for specified current draw at Magnalock Section 2
Problem Reduced Holding Force Points of Reference
Check DC power source is Full-Wave Rectified
(Half-wave Rectifier or AC Power unacceptable)
Section 5.3.2
Check for specified voltage at Magnalock Section 2
Check for specified current draw at Magnalock Section 2
Check strike mounting for proper installation Section 5.2.1 and 5.2.5
Solution
Check the Magnalock and strike for obstructions
and that contact surfaces are properly cleaned Section 8
Problem BondSTAT Does Not Report Secure Points of Reference
Check for specified voltage at Magnalock Section 2
Check for specified current draw at Magnalock Section 2
Check strike mounting for proper alignment and
pivoting for proper closure to Magnalock Table A / Section 5.2.4
Solution
Check the Magnalock and strike for obstructions
and that contact surfaces are properly cleaned Section 8
Problem DPS Does Not Report Door Status Points of Reference
Check strike mounting for proper alignment Table A / Section 5.2.4
Check for proper door closure Section 8.1
Check for proper voltage/current on switch Section 2
Solution
Check resettable protection device Section 1
Problem The Magnalock Does Not Release Points of Reference
Make sure no voltage is present at Magnalock Section 2
Make sure the Magnalock is not drawing current Section 2
Check if the strike is sticky and hard to release Section 8
Solution
Check the Magnalock and strike for obstructions
and that contact surfaces are properly cleaned Section 8
Problem The Magnalock is Dirty or Rusty Points of Reference
Solution Improper cleaning – Maintenance Equipment Section 8
Problem Electronic Noise Interference with
Access Control System Points of Reference
Solution
Check for voltage from Magnalock to door frame.
There should be no voltage present.
Section 2
IF PROBLEMS PERSIST CALL SECURITRON TOLL FREE
(800) MAG-LOCK
[phone]

PN# 500-10420
Page 12 Rev. E, 05/08
Appendix B
Wire Gauge Factoring
1.1 Remote Power Supply
xThe Magnalock requires adequate voltage and current for proper operation.
xResistance is created by the length and gauge (size) of the wire being used.
xAn accurate estimated distance from the power supply to the opening is crucial.
xFor superior operation the correct size gauge wire must be used.
xThe devices used operate the best with the least amount of resistance on the source.
xUsing the correct gauge wires protects against large voltage and current (load) losses.
xThe gauge is determined by the wire distance, voltage and current of all devices.
1.2 Determining Wire Gauge
xFollow Example A (12VDC system) and Example B (24VDC system) below.
xUse Tables 1 and Table 2 to choose the correct wire gauge for the application.
1.2.1 Example A: (12VDC system)
Devices Used Amps (12VDC) Progressive Totals
M62 Magnalock 0.250 0.250
DK-26 Access 0.160 0.410
XMS Motion 0.050 0.460
EEB2 Timer 0.025 0.485
Total Current Rounded Up (Table 1) 0.600A
Using Table 1 (12VDC) Find: - Current Draw .600 Amps
- Wire Distance 200 Feet (One-Way)
Solution: 18 Gauge is indicated for proper installation
1.2.2 Example B: (24VDC system)
Using Table 2 (24VDC) Find: - Current Draw .400 Amps
- Wire Distance 1000 Feet (One-Way)
Solution: 14 Gauge is indicated for proper installation
Devices Used 24VDC Amps Progressive Totals
M82 Magnalock 0.200 0.200
TSB Touch Bar 0.025 0.225
DK-11 Access 0.070 0.295
XDT-24 Delay 0.050 0.345
MK Bypass/Reset 0.020 0.365
Total Current Rounded Up (Table 2) 0.400A

PN# 500-10420
Page 13 Rev. E, 05/08
TO SOLVE: INTERSECT ROW (Current) and INTERSECTING COLUMN (Wire Distance)
1.00A 20
Gauge
18
Gauge
16
Gauge
14
Gauge
14
Gauge
12
Gauge
10
Gauge
10
Gauge
8
Gauge
.800A 22
Gauge
18
Gauge
18
Gauge
16
Gauge
14
Gauge
12
Gauge
10
Gauge
10
Gauge
8
Gauge
.600A 22
Gauge
20
Gauge
18
Gauge
18
Gauge
16
Gauge
14
Gauge
14
Gauge
12
Gauge
10
Gauge
.400A 22
Gauge
22
Gauge
20
Gauge
18
Gauge
18
Gauge
16
Gauge
14
Gauge
14
Gauge
12
Gauge
.300A 24
Gauge
22
Gauge
22
Gauge
20
Gauge
18
Gauge
18
Gauge
16
Gauge
14
Gauge
14
Gauge
C
U
R
R
E
N
T
.200A 24
Gauge
22
Gauge
22
Gauge
22
Gauge
20
Gauge
18
Gauge
18
Gauge
16
Gauge
14
Gauge
50’
[15m]
100’
[30m]
150’
[46m]
200’
[61m]
300’
[91m]
400’
[122m]
500’
[152m]
750’
[229m]
1000’
[305m]
12VDC
WIRE DISTANCE
Table 1
1.0A 22
Gauge
20
Gauge
20
Gauge
18
Gauge
16
Gauge
14
Gauge
14
Gauge
12
Gauge
10
Gauge
.800A 22
Gauge
22
Gauge
20
Gauge
18
Gauge
18
Gauge
16
Gauge
14
Gauge
14
Gauge
12
Gauge
.600A 24
Gauge
22
Gauge
22
Gauge
20
Gauge
18
Gauge
18
Gauge
16
Gauge
14
Gauge
14
Gauge
.400A 24
Gauge
22
Gauge
22
Gauge
22
Gauge
20
Gauge
18
Gauge
18
Gauge
16
Gauge
14
Gauge
.300A 24
Gauge
24
Gauge
22
Gauge
22
Gauge
22
Gauge
20
Gauge
20
Gauge
18
Gauge
16
Gauge
C
U
R
R
E
N
T
.200A 24
Gauge
24
Gauge
24
Gauge
22
Gauge
22
Gauge
22
Gauge
20
Gauge
20
Gauge
18
Gauge
50’
[15m]
100’
[30m]
150’
[46m]
200’
[61m]
300’
[91m]
400’
[122m]
500’
[152m]
750’
[229m]
1000’
[305m]
24VDC
WIRE DISTANCE
Table 2
xThe Wire Distance indicated on the table above represents a 2-wire “One-Way”
length from the power supply source to entryway installation area.
xThe Gauge values specified on the table above represent a 2-wire “Round Trip”
length from the power supply source to entryway installation and returning back
to the power supply source.
IMPORTANT
THE 200’ [61m] WIRE RUN IN EACH TABLE FACTORS A 400’ [122m] ROUND TRIP

PN# 500-10420
Page 14 Rev. E, 05/08
MAGNACARE
£
LIMITED LIFETIME WARRANTY
SECURITRON MAGNALOCK CORPORATION warrants that it will replace at customer’s request,
at any time for any reason, products manufactured and branded by SECURITRON.
SECURITRON will use its best efforts to ship a replacement product by next day air freight at
no cost to the customer within 24 hours of SECURITRON’s receipt of the product from
customer. If the customer has an account with SECURITRON or a valid credit card, the
customer may order an advance replacement product, whereby SECURITRON will charge the
customer’s account for the price of the product plus next day air freight, and will credit back
to the customer the full amount of the charge, including outbound freight, upon
SECURITRON’s receipt of the original product from the customer.
SECURITRON’s sole and exclusive liability, and customer’s sole remedy, is limited to the
replacement of the SECURITRON product when delivered to SECURITRON’s facility (freight
and insurance charges prepaid by customer). The replacement, at SECURITRON’s sole
option, may be the identical item or a newer unit which serves as a functional replacement.
In the event that the product type has become obsolete in SECURITRON’s product line, this
MAGNACARE warranty will not apply. This MAGNACARE warranty also does not apply to
custom, built to order, or non-catalog items, items made by others (such as batteries),
returns for payment, distributor stock reductions, returns seeking replacement with anything
other than the identical product, or products installed outside of the United States or Canada.
This MAGNACARE warranty also does not apply to removal or installation costs.
SECURITRON will not be liable to the purchaser, the customer or anyone else for incidental
or consequential damages arising from any defect in, or malfunction of, its products.
SECURITRON does not assume any responsibility for damage or injury to person or property
due to improper care, storage, handling, abuse, misuse, or an act of God.
EXCEPT AS STATED ABOVE, SECURITRON MAKES NO WARRANTIES, EITHER EXPRESS OR
IMPLIED, AS TO ANY MATTER WHATSOEVER, INCLUDING WITHOUT LIMITATION THE
CONDITION OF ITS PRODUCTS, THEIR MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE.
PATENTS
The Securitron Magnalock is listed under U.S. patent #4,516,114 and 4,682,801.
Additional patents pending.

PN# 500-10420
Page 15 Rev. E, 05/08

PN# 500-10420
Page 16 Rev. E, 05/08
Why choose a genuine Magnalock ?
The Securitron Advantages...
Electrical Advantages
• Low Current Consumption (125mA-350mA)
Less Heat for Longer Product Life
Smaller Gauge Wire
Longer Wire Runs
Smaller Power Source
Job Cost Savings
Double/Triple the Battery Back-up Time for a Secure Facility
• Patented “State of the Art” Electronic Circuitry
Instant Release Circuit “50 Milliseconds”
No Inductive Kickback
No Welded Switch Contacts
Built-in Noise Suppression
No Interference with Sensitive Electronics
• Smart Auto Switching Dual Voltage
No Jumpers, No Switches, No Errors
Sealed and Weatherproof
• Securitron Magnetic Locks are 100% Plated & Sealed
(excludes M38 & M68 series)
Outdoor Installation; Gates, Pool Areas, and Marina
Stainless Steel lock casing will not rust
Operating Temperature: -40F to +140F [-40C to +60C]
• Optional Universal Conduit Fitting (M62 & M82)
Secures and Conceals Magnetic Lock cable
Increases the Integrity of the Lock
Mounting Hardware, Brackets and Tools
• Aerospace Collapsing Blind Nuts
1000 lbs tensile strength per blind nut
• Grade One Machine Screws 1/4-20
Allows use of “Thread Locker” adhesive
• Complete Line of Mounting Hardware for Doors & Frames
Herculite, glass, aluminum, metal clad, and wood
• Optional Installation Kit
A real “Tools of the Trade” kit that reduces installation error and speeds
installation time - increasing profits
• M38 & M68
Integrated mounting bracket and built-in wire access chamber
Fast, easy and fool-proof installation
You don’t become the best selling or best warrantied products in the industry without a few
firsts.
1ST “E” profile electromagnetic lock
1ST sealed & weatherproof electromagnetic lock
1ST electromagnetic lock that suppresses inductive kickback and electronic noise and provides
instant release
1ST electric lock to mount in a standard door strike opening without cutting the frame (UnLatch)
1ST manufacturer in the security industry to offer a “no strings attached” lifetime replacement
warranty (MagnaCare)
1ST electromagnetic lock manufacturer to achieve ISO 9001 certification