Assa Abloy Yale Smart Latch User manual

ISL-1290-01
Contents Include
Before getting started
Ⓐ
Ⓑ
Ⓒ
Ⓓ
Can you open with your key in both directions? Please go to step
Check Point
Door Preparation
Disassemble Lockset
Ⓒ
Ⓓ
Ⓑ
20mm Hole
.
Fit Yale digital lock using hand Phillips screwdriver to avoid cross threading xing
screws. If using a cordless, please ensure it is set to low speed & torque.
Are you installing the Yale Smart Latch with a new Nightlatch?
NO, I am going to keep using the existing Nightlatch on my door with the with the Yale Smart Latch.
There are many types of Nightlatches, so please start from installation step BELOW, and follow
the check points for correct installation.
Can you open with your key only in the
left direction? Not in the right direction?
PLEASE GO TO STEP
Your Nightlatch needs an additional plate
Please attach the additional handing plate tightly
onto the cylinder xing surface.
The plate must be aligned with the shape.
Make sure the 'LEFT TURN' is shown as the image
below if your latch is opened only to the LEFT
direction by the key.
Self adhesive pad Self adhesive pad
Please attach the additional handing plate tightly
onto the cylinder xing surface.
The plate must be aligned with the shape.
Make sure the 'RIGHT TURN' is shown as the image
below if your latch is opened only to the RIGHT
direction by the key.
Please use the key of your existing Nightlatch and check the below
Keep your door open
Insert the key in the outside cylinder key hole
Turn the key 90°clockwise (to the right) and check the latch fully retracts
Turn the key 90° counter clockwise (to the left)
and check the latch fully retracts
Please disassemble your existing Nightlatch
case and mounting plate.
Please read the intructions before tting and
using the Yale Smart Latch.
The functions and design of this product can be
changed without prior notice for performance
and quality improvements.
*The Nightlatch and plates above are generic
images. If you are retrotting the Yale Smart
Latch, your existing Nightlatch may be different.
Yes, I have bought the Yale Smart Latch with a new Nightlatch to install them onto my door.
Please start from installation step ON THE RIGHT PAGE
Front Body Battery Pack Handing Plate
Screws
Batteries
Self adhesive
pad
KEY
900
20mm Hole
Use template
provided
72.5mm
60mm
32mm Hole
900
(L)
Can you open with your key only in the
right direction? Not in the left direction?
At the height you want your lock, use a pencil to mark a spot exactly 60mm from the edge
of the door. At that spot, drill a 32mm diameter hole through the door. Or if using an
existing cylinder hole, use the template to mark the position for the 20mm hole.
PLEASE GO TO STEP
Your Nightlatch needs an additional plate
(R)
The smarter way to protect your home.
Smart Latch

Cut Connecting Bar
Mount External Keypad and Mounting Plate Nightlatch Installation
Insert Batteries and Close the Cover
Check Points after Installation
Secure Battery Pack
*
Ⓐ
①
Ⓑ
Ⓒ
Ⓓ
Ⓔ
Door Template
ø32mm
ø20mm
Connect the cable to
the battery pack.
Make sure battery back is
square with the door.
Screw into boss. Fix screw to completely
secure battery pack.
Feed the cable through the slot and then, being careful
not to overlap it, zig-zag any excess cable
behind the battery pack.
*Nightlatch shown is for illustration only and
may not be available.
Inside Outside
Cut with pliers to ensure a clean cut.
Place the Electronic Keypad into the holes on the outside of the door. Now
measure and cut the connecting bar to the required length.
Use the template provided to
choose correct screw length
according to your door thickness.
Make sure the front keypad is aligned before xing the
screws tightly. Now x the mounting plate onto the door.
Don't overtighten the screws, as this may cause the lock to
bind and not function smoothly.
Finish the installation of your nightlatch using
the mounting instructions.
Note: For a new Nightlatch, please refer to
separate latch mounting instructions for
specic retaining screw hole pattern.
Warning: The projection of the connecting bar is important to ensure the lock works correctly,
and may differ depending on the Nightlatch. If this is cut too short, it cannot be replaced.
Door Thickness
Fit rst
Make sure to leave the door open when registering your PIN because you may
accidentally lock the door while trying to register or change your PIN code.
Touch the keypad with your palm to wake up the keypad.
Enter a PIN code 123456 and enter * button or touch the keypad with
your palm to open the door.
Turn the thumbturn several times to retract the latchbolt.
The thumbturn will not retract the latchbolt after few seconds.
PLEASE NOTE: Remember to change your master code after installation.
To avoid any possibility of being locked out, do not close the door until
a PIN code has been successfully registered to allow access.