ATD Tools ATD-7461 User manual


ATD-7461
1,500 LBS Motorcycle/ATV Jack
Operating Instructions and User Cautions
CAUTION:Beforeusingthisproduct,readthismanualandfollowallSafetyRulesandOperationalInstructions.



Ownerand/orOperatorResponsibility
Theownerand/oroperatorshallstudytheproductinstructionsandretainthemforfuturereference.
Operation
Theownerand/oroperatorshallhaveanunderstandingoftheproduct,itsoperatingcharacteristics,
andsafetyoperatinginstructionsbeforeoperatingthePALD(PortableAutomotiveLiftingDevice).
Safetyinformationshallbeemphasizedandunderstood.IftheoperatorisnotfluentinEnglish,the
productandsafetyinstructionsshallbereadtoanddiscussedwiththeoperatorintheoperator's
nativelanguagebythepurchaser/ownerorhisdesignee,makingsurethattheoperatorcomprehends
theircontents.
Maintenance
ThePALDshallbemaintainedinaccordancewiththeproductinstruction.
1.Whenjackisnotinuse,liftingarmshouldbeinfulldownposition.
2.Alwayskeepjackcleanandkeepthescrewandbearingswelllubricated.
3.Keepmovingpartsclean;lubricatemovingpartsevery3months.
Inspection
(a)VisualinspectionshallbemadebeforeeachuseofthePALDbycheckingforabnormalconditions,
suchascrackedwelds,leaks,anddamaged,loose,ormissingparts.
(b)Otherinspectionsshallbemadeperproductoperatinginstructions.
(c)EachPALDshallbeinspectedimmediatelyifthedeviceisbelievedtohavebeensubjectedtoan
abnormalloadorshock.Itisrecommendedthatthisinspectionbemadebyamanufacturer'sor
supplier'sauthorizedrepairfacility.
(d)Ownersand/oroperatorsshouldbeawarethatrepairofthisequipmentmayrequirespecialized
knowledgeandfacilities.ItisrecommendedthatanannualinspectionofthePALDbemadebya
manufacturer'sorsupplier'sauthorizedrepairfacilityandthatanydefectiveparts,decals,orsafety
labelsorsignsbereplacedwithmanufacturersorsupplier'sspecifiedparts.Alistofauthorizedrepair
facilitiesisavailablefromthemanufacturerorsupplier.
DamagedEquipment
AnyPALDthatappearstobedamagedinanyway,isfoundtobewornoroperatesabnormallySHALL
BEREMOVEDFROMSERVICEUNTILREPAIRED.Itisrecommendedthatnecessaryrepairsbemadeby
amanufacturer'sorsupplier'sauthorizedrepairfacilityifrepairsarepermittedbythemanufactureror
supplier.
Alterations
Becauseofpotentialhazardsassociatedwiththistypeofequipment,noalterationsshallbemadeto
theproduct.
AttachmentsandAdaptors
Onlyattachmentsand/oradaptorssuppliedbythemanufacturershallbeused.




SafetyMarkings
(a)Study,understand,andfollowallinstructionsbeforeoperatingthisdevice.
(b)Donotexceedratedcapacity.
(c)Useonlyonhard,levelsurfaces.
(d)Centerloadonliftplatform.
(e)Liftonlythoseareasoftheautomotivevehiclespecifiedbyitsmanufacturer.
(f)Immediatelyafterliftingload,ensureliftmechanicalloadholdingmeansisengaged.
(g)Beforemoving,lowertheloadtothelowestpossiblepoint.
(h)Secureloadwithappropriaterestraintdevice.
(i)Failuretoheedthesemarkingsmayresultinpersonalinjuryand/orpropertydamage.

SafetyMessages
(a)Useofthisproductislimitedtolifting,lowering,transportingandstoringintheloweredposition,loadsconsisting
ofasinglemotorvehiclewhoseliftpointsarecompatiblewiththeliftplatform.Incompatibilityisevidentwhenthe
loadedvehiclewobbles,appearsunstable,and/ordoesnotsecurelyengagetheliftplatform.
(b)Restraininganincompatibleloadwillnotmaketheloadsecureandmaycauseunexpectedlossofload.
(c)Neverworkon,aroundorunderaloadthatisnotsecuredandstable.
(d)Keepoperator’sandbystander’shead,handsandfeetawayfromliftarmswhenraisingandlowering.
(e)Noalterationsshallbemadetothisproduct.
(f)Onlyattachments,restraints,oradapterssuppliedbythemanufacturershallbeused.

IMPORTANT
DONOTOVERLOADJACKBEYONDITSRATEDCAPACITY.NEVERMOVETHEJACKWHILEITISSUPPORTINGLOAD.
Sometimesduringshipmentandhandling,airmaybecometrappedinthehydraulicsystemcausingpoorornolifting.




ASSEMBLYINSTRUCTIONS
1.Placehydraulicram(#H)ontothebase(#A)using(2)M8X25hexbolt(#4),(2)springwasher(#2),(2)washer
(#1),andusingboltM5X25(#8)tofixramtoconnectingrod(#D)thentighten.
2.Insertfootpedal(#I)tothehydraulicram(#H),andsecureusingM8X30bolt(#3).
3.Placesafetylockoperationrod(#L)inserttolink(#B)using(2)washer(#6),(2)lockingpin(#7)andlockingrod(#5).
4.Inserthandle(#E)toconnectingrod(#D)usingboltM8X30(#3).
5.Ensurethatallconnectionsaretightened
OPERATINGINSTRUCTIONS
Seedrawingonpage3forlocationofparts.
TORAISETHELOAD
1.Placejackonahardlevelsurface.
2.Toavoiditemfromslippingduringtheraisingoperation.ALWAYSfirstdeterminethecenteroftheweightload.
3.PlacethejackundertheitemsothattheLiftSaddleispositionedunderthecenteroftheweightload.
4.Pumpthefootpedaluntiltheliftsaddlecomesincontactwiththeloadtobelifted;proceedtolockwheelcasters.
Alwayschecktobesurethatthesaddleandtheloadarepositionedcorrectlybeforeraisingthejack.
5.UseFootPedaltoraiseload;BESUREthatSafetyLockissecuredinoneofthreestatedlockpositionsoncedesired
heightisreached.
6.Applytie‐downstraps(Seepage5,SecuringtheLoad)onceloadhasbeenraisedtodesiredheight.Thoroughly
tightenstraps.
7.Stabilizeloadedjackonahardsurfaceformaximumbalancebyadjustinglockingscrews.

TOLOWERTHELOAD
1.RaisethejackslightlyandpullbackontheOperationRod,releasingtheSafetyLock.
2.FastentheOperationRodtotheconnectingrodifyouareloweringtheloadcompletely.
3.PresstheReleaseValveverygentlytolowertheSaddleanditsload.

CAUTION:TieDownStrapswillbecomelooseandloadwillbereleaseduponloweringtheload.

4.Removethetiedownstrapsaftertheloadissecured.
SECURINGTHELOAD‐1‐in.x15‐ft.RatchetTieDownStraps

1.Connectstraphookstoloop(P)andplacestrapoverload.
2.WiththestrapHandle(A)intheclosedposition,takelongstrapendandslipitthroughtheinsertslotinSpindle(B).
Pullstrapbackoverspindle.
3.Tightenthestrapbyratchetingthehandlebackandforthuntiltheloadissecure.Ifnecessary,takeuptheexcess
slackbyhanduntilthestrapistight.

CAUTION:Toavoiddamagetotheload,DONOTovertighten.


4. To lock ratchet, ALWAYS leave the handle in the closed position.
RELEASING THE LOAD-1-in. x 15-ft. Ratchet Tie Down Straps
Working limited: 250Lbs
Max load capacity: 800Lbs
1. Hold the ratchet in one hand and with the other hand pull back on Release Latch (C) that is located on
Handle (A).
2. While holding Release Latch (C) back, open Handle (A) fully past the locking gears until Latch (C) locks in a
completely open position or until the load releases.
CAUTION:The load will release at this point.
3. To loosen or remove strap, pull up on ratchet and slide strap out of Spindle (B).


FORTIEDOWNSTRAP
1.DONOTusetiedownstrapfortowingvehiclesortoholdorsuspendhumanweight.
2.DONOTuseextensionbarlever,pliersoranytoolstooperateasahandle.Usehandpoweronly.
3.Protectstrapwebbingfromsharpedges,heatandacid.Replacestrapwebbingifitiscut,wornordamaged.Inspect
strapwebbing,hooksandhardwarebeforeeachuse.

MAINTENANCE
IMPORTANT:BeforeperforminganymaintenanceofthebottlejackALWAYSdetachfromtheframeand
placeonalevelsurface.AIRPURGINGINSTRUCTIONSWiththeramfullyretracted,locateandremovethe
oilfillerplug.InsertthefootpedalintothesleeveofHydraulicRam,andthenpump6to8strokes.Thiswill
helpreleaseanypressurizedairwhichmaybetrappedinthereservoir.Besurethattheoillevelisjust
belowtheoilfillerplughole.Reinstalltheoilfillerplug.Sometimesduringshipmentandhandling,airmay
becometrappedinthehydraulicsystemcausingpoorornolifting.

OILLEVEL:
IMPORTANT:Whenaddingorreplacingoil,alwaysuseagoodgradeofhydraulicjackoil,transmissionoilor
turbineoilandalwaysavoidmixingdifferenttypesofoil.Neverusebrakefluid,alcohol,glycerine,
detergentmotoroilordirtyoilofanykind.Improperoilusagewillcauseseriousinternaldamagetojack.
ADDINGOIL:Withramfullyloweredandjackonlevelground,removeoilfillplug.Addoiliflevelismore
than1/4"belowholereplacecoverplate.
REPLACINGOIL:Forbestperformanceandlongestlife,oilshouldbereplacedatleastonceeveryyear.To
drainoil,removecoverplate,oilfillerplugandreleasevalve.BeVERYCAREFULtonotallowdirtorany
foreignmatterintothesystem.
LUBRICATION:Putgreaseinfittingonbaseandlubricateliftingarmspindlewithoil,every3months.


RUSTPREVENTION:Cleanandwipewithanoilycloth,thepistonramandpumppistonevery3monthsor
whensignsofrustorcorrosionappear.Whennotinuse,alwaysleavethesaddleandpumppistoninthe
completelydownposition.
TROUBLE SHOOTING CHECK LIST
OneYearWarranty
EveryATDToolsproductisinspectedbeforeleavingthefactory.Thisproductiswarrantedtobefreeof
defectsinmaterialandworkmanship.ATDToolselectstoreplacefreeofchargeorsupplypartsforrepair,withthe
sameorlikeitemofequalvalueanyitemfoundtohavedefectsinmaterialsorworkmanshipduringthefirst1yearof
customerownershipwithproofofpurchase.Proofofpurchasemustbeeitheroriginalorclearcopyofyourstore
receipt.Simplyreturnitemtothepointofsaleforreplacementorreplacementparts.Thiswarrantygivesyouspecific
legalrightsandyoumayalsohaveotherrightswhichmayvaryfromstatetostate.ATDTools,ATDToolsEmblemand
theATDToolsrelatedgraphicsareATDToolsInc.Trademarksandareusedunderlicense.MadeinChina.

ForoutofwarrantyRepairOrReplacementParts:
Pleasecalltollfree1‐800‐592‐8665,MondaythroughFridaybetweenthehoursof8:00AMto8:00PM
(EasternStandardTime).ReplacementPartsrequestcanalsobesubmittedviatheweb,24hoursdaily
atwww.americancustomerservice.com.Inallcorrespondence,pleaseincludemodel#,part#,part
descriptionandquantityrequired.Name,ShippingAddressandDayTimeTelephonenumber,including
areacode,arerequiredtoprocessyourpartsshipmentrequest.







