ATD Tools ATD-7317 Instructions for use

7137-DTA:ledoM
noT2:yticapaC
1
ATD-7317
Low Profile Service Jack
Capacity Min. Height Max Height Handle
Length
Overall
Length
Overall
Width
Saddle
Diameter
Shipping
Weight
2 Ton 2 3/4” 24” 49-1/4” 36” 15-1/8” 4” 106 LB
Contents:
Page: 1. Specificaons
2. Safety & Warning Informaon
3. & 4. Setup, Operaon & Prevenve Maintenance
5. Inspecon, Storage & Troubleshoong
6. Exploded View & Replaceable Part Numbers
7. Warranty Informaon
8. Prevenve Maintenance Record Log
O
p
eran
g
Instrucons & Parts Manual

7137-DTA:ledoM
noT2:yticapaC
2
SAFETY & WARNING INFORMATION
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
Before operang this device, be sure to read all content within this manual, ensuring that you
understand the operang procedures, maintenance requirements and all safety warnings.
The owner and/or operator shall have an understanding of the product, its operang
characteriscs, and safety operang instrucons before operang this device. Safety informaon
shall be emphasized and understood. If the operator is not fluent in English, the product and
safety instrucons shall be read to and discussed with the operator in the operator’s nave
language by the purchaser/owner or his designee, making sure that the operator comprehends
their contents.
Acons to help prevent dangerous situaons
Study, understand, and follow all instrucons before operang this device.
Do not exceed the rated capacity stated.
Use only on hard level surfaces.
This item is to be used as a liing device only. Immediately aer liing, support the
vehicle with appropriate means.
Do not move or dolly the vehicle while it is on the jack.
Li only on areas of the vehicle as specified by the vehicle manufacturer.
No alteraons shall be made to this product.
Failure to heed these markings may result in serious personal injury and/or property
damage.
This is the safety noficaon symbol.
This symbol will nofy you of any
potenal injury hazards. Please
follow all instrucons that follow this
symbol to avoid possible injuries or
death.
Indicates a hazardous
situaon. If proper steps are
not followed, death or
serious injury could result.

7137-DTA:ledoM
noT2:yticapaC
3
SETUP, OPERATION & PREVENTIVE MAINTENANCE
Setup
Prior to each use, visual inspecon (See Pg. 5) shall be made to the device by checking
for abnormal condions, such as cracked welds, leaks, and damaged, loose, or missing
parts.
Consult the vehicle owner’s manual to determine the locaon of li points.
Be sure to set the vehicle in park with the emergency brake on and wheels securely
chocked.
Be sure that the vehicle and the jack are on a hard, level surface.
Assembly
If two piece handles are provided, assemble the upper secon into the lower secon,
line up the holes, insert and ghten the screw.
Insert the boom end of handle into handle fork and securely ghten the bolt and
washer. Ensure the handle can turn freely.
Liing
Turn the handle/release valve clockwise to the closed posion. Do not over ghten.
Posion the jack under the specified li point.
Begin liing by pumping the handle up and down.
Immediately aer liing, support the vehicle with appropriately rated jack stands.
Turn the handle/release valve slowly counterclockwise to lower the vehicle onto jack
stands.
Lowering
Turn the handle/release valve clockwise to the closed posion. Do not over ghten.
Pump the handle up and down to livehicle off jack stands.
Remove the jack stands. Do not get under or let anyone get under the vehicle while
lowering.
Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the
ground
.

7137-DTA:ledoM
noT2:yticapaC
4
SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.)
Maintenance
NOTICE: Use high grade hydraulic oil only. Never use brake fluid, motor oil, transmission fluid,
turbine oil or any other fluids. ISO-VG22 or equivalent hydraulic oil is recommended.
Check and Refill Oil
With the jack in the fully lowered, level posion, if unit cover is provided, remove unit
cover, then remove oil filler plug.
Proper oil level should be just covering inner cylinder as seen from the oil filler plug
hole.
Do not overfill. Always fill with new, clean hydraulic jack oil as recommended above.
Reinstall oil filler plug, then reinstall unit cover.
Lubricaon and Cleaning
Periodically clean and lubricate all moving parts and pivot points.
Air Venng Procedures
With the jack in the fully lowered posion, release valve open, remove oil filler plug.
Pump the handle rapidly several mes. Reinstall oil filler plug.
Turn the handle/release valve clockwise to the closed posion.
Pump the handle unl the li arm reaches maximum height and connue to pump
several mes to remove trapped air in the system.
Turn the handle/release valve counterclockwise in one full turn and lower li arm to the
lowest posion. Use force on saddle if necessary.
Carefully and slowly loosen oil filler plug to release pressurized air.
Repeat above steps unl trapped air is completely vented.
Damaged Equipment
Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally
SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that necessary repairs
be made by a manufacturer’s or supplier’s authorized repair facility if repairs are permied by
the manufacturer or supplier.
Alteraons
Because of potenal hazards associated with this type of equipment, no alteraons shall be
made to the product.
Aachments and Adapters
Only aachments and/or adapters supplied by the manufacturer shall be used.

7137-DTA:ledoM
noT2:yticapaC
5
INSPECTION, STORAGE
&
TROUBLESHOOTING
Inspecon
Visual inspecon shall be made before each use of the device by checking for abnormal
condions, such as cracked welds, leaks, and damaged, loose, or missing parts.
Other inspecons shall be made per product operang instrucons.
This device shall be inspected immediately if the device is believed to have been
subjected to an abnormal load or shock. It is recommended that this inspecon be made
by a manufacturer’s or supplier’s authorized repair facility.
Owners and/or operators should be aware that repair of this equipment may require
specialized knowledge and facilies. It is recommended that an annual inspecon of the
product be made by a manufacturer’s or supplier’s authorized repair facility and that
any defecve parts, decals, or safety labels or signs be replaced with manufacturers or
supplier’s specified parts.
Storage
This Jack should be stored in a dry locaon on a level surface.
Troubleshoong
Symptom Possible Causes Soluon
Jack will not li the load. 1. Release valve not ghtly
closed.
2. Low oil level.
3. Defecve or worn internal
parts.
4. Load exceeds maximum
allowance.
1. Tighten release valve.
2. Check and add oil. Follow “Check
and Refill Oil” instrucons on Pg.4.
3. Disconnue use and contact a
local repair center.
4. Use a higher capacity jack.
Jack will not hold the load. 1. Release valve not ghtly
closed.
2. Power unit malfuncon.
1. Tighten release valve.
2. Disconnue use and contact a
local repair center.
Jack will not descend to
minimum height, or will not
remain in lowered posion.
1. Air trapped in system.
2. Reservoir oil overfilled.
1. Vent air out of system. Follow
“Air
Venng Procedures” above.
2. Check and ensure proper oil
level. Follow “Check and Refill Oil”
instrucon on Pg.4.
Jack will not li to max
height.
1. Low oil level. 1. Check and ensure proper oil level.
Follow “Check and Refill Oil”
instrucons above.
Jack will not funcon
properly aer tried soluon.
1. Internal malfuncon or
structural damage.
1. Stop usage and contact an
authorized repair center.

7137-DTA:ledoM
noT2:yticapaC
6
EXPLODED VIEW & REPLACEABLE PART NUMBERS
* Items not idenfied by part number are not available for replacement.
Item Part Number* Descripon Qty
1 LYD2G-100 Front wheel assembly 2
2 LYD2K-300 Saddle w/pad 1
3 GB1152-89-M6 Grease Fing 1
4 LYD3J-3 Cover 1
5 LYD3F-600 Handle Assembly w/ foam 1
6 LYD2-9A Return Spring 2
7 LYDBI-2T.3 Power Unit Assembly 1
8 LYD3G-300 Handle Fork Assembly 1
9 LYD3G-400 Rear Caster Assembly 2
10 LYDBI-3T-17 Handle foam only 1
11 LYD2K-3B Saddle pad only 1
N/A LYD3F-100 Oil Filler Screw w/ Seal 1

7137-DTA:ledoM
noT2:yticapaC
7
WARRANTY INFORMATION
ONE YEAR LIMITED WARRANTY
For a periodof one (1) year from your purchase date, ATD Tools, Inc. will repair or replace (at its
option) withoutcharge, your ATD product ifitwas purchasednew and the producthas failed
due to a defect in material or workmanship which you experienced during normal use of the
product. This limited warranty isyour exclusive remedy.
To access the benefits of this warranty, contact the ATD warranty center at1-844-364-9922 for
confirmationthat this warranty applies. Thereafter, you may be advised to return the product
under warranty, freight prepaid, to the ATD Tools, Inc. service department.
If this ATD product is altered, abused, misused, modified, or undergoes service by an
unauthorized technician, your warranty will be void. We arenot responsible for damage to
ornamental designs youplace on thisATD productand such ornamentation should notcover
any warnings or instructions or they may void the warranty. This warranty does not cover
scratches, superficial dents, and other abrasions to the paint finish that occur under normal use.
Subject to the law in your state:
(1) Your sole and exclusive remedy is repair or replacement of the defectiveproduct as
described above.
(2) ATD Tools, Inc. isnot liable for anyincidental damages, including butnot limited to, lost
profits and unforeseeable consequences.
(3) The repair and replacementof this productunder the express limited warranty described
above is your exclusive remedyand is provided in lieu ofall other warranties, express or
implied.All other warranties,including implied warranties and warranties of
merchantability or fitness for a particular purpose are disclaimed and,ifdisclaimer is
prohibited, these warranties are limited to one year from your date of purchase of this
product.
Some states’ lawsdo notallow limited durations on certain implied warranties and some states’
lawsdo not allow limitationson incidental or consequential damages.You should consult the
law in your state to determine how your rights may vary.
Made in China to ATD Tools, Inc. Specificaons
Visit us at www.atdtools.com
Warranty Service Number 1-844-364-9922
For Non-warranty issues, please contact your supplier.
Printed In China

7137-DTA:ledoM
noT2:yticapaC
8
PREVENTIVE MAINTENANCE RECORD LOG
Date Maintenance Performed