Atlas PV-15PX User manual

Revised 5/15/2020
Read this entire manual before operation begins.
Record below the following information which is located on the serial number
data plate.
Serial No.
Model No.
Date of Installation

Contents
General Information. . . . . . . . . . 5
Product Identification . . . . . . . . . 8
Packing, Transport, Storage . . . . . . 9
Lift Description . . . . . . . . . . . .11
Technical Specification. . . . . . . . .12
Safety . . . . . . . . . . . . . . . .18
Installation . . . . . . . . . . . . . .21
Operation And Use . . . . . . . . . .32
Maintenance . . . . . . . . . . . . .34
Troubleshooting. . . . . . . . . . . .36
Parts List . . . . . . . . . . . . . . .37
Warranty . . . . . . . . . . . . . . .53

4
PV-15P
PRINTING CHARACTERS AND SYMBOLS
Throughout this manual, the following symbols and
printing characters are used to facilitate reading:
Indicates the operations which need proper care
Indicates prohibition
Indicates a possibility of danger for the operators
BOLD TYPE Important information
WARNING: before operating the lift and carrying out any
adjustment, read carefully chapter 7 “installation” where all
proper operations for a better functioning of the lift are shown.

General Information 5
PV-15P
General Information
This chapter contains warning instructions to operate the lift properly and
prevent injury to operators or objects. This manual has been written to be used
by shop technicians in charge of the lift (operator) and routine maintenance
technician (maintenance operator). The operating instructions are an integral
part of the machine and must remain with it for its whole useful life. Read every
section of this manual carefully before operating the lift and unpacking it since it
gives helpful information about:
• Safety Of People
• Safety Of The Lift
• Safety Of Lifted Vehicles
The company is not liable for possible problems, damage, accidents, etc.
resulting from failure to follow the instructions contained in this manual. Only
skilled technicians of AUTHORIZED DEALERS or SERVICE CENTERS AUTHORIZED
by the manufacturer shall be allowed to carry out lifting, transport, assembling,
installation, adjustment, calibration, settings, extraordinary maintenance,
repairs, overhauling and dismantling of the lift.
The manufacturer is not responsible for possible damage to people,
vehicles or objects if said operations are carried out by unauthorized
personnel or the lift is improperly used.
Any use of the machine made by operators who are not familiar with the
instructions and procedures contained herein shall be forbidden.
1.1 Manual Keeping
For a proper use of this manual, the following is recommended:
• Keep the manual near the lift, in an easily accessible place.
• Keep the manual in an area protected from the damp.
• Use this manual properly without damaging it.
• Any use of the machine made by operators who are not familiar with the
instructions and procedures contained herein shall be forbidden.
This manual is an integral part of the lift: it shall be given to the new owner if
and when the lift is resold.

General Information 6
PV-15P
1.2 Obligation In Case Of Malfunction
In case of machine malfunction, follow the instructions
contained in the following chapters.
1.3 Cautions For The Safety Of The Operator
Operators must not be under the influence of sedatives, drugs, or alcohol when
operating the machine.
Before operating the lift, operators must be familiar with
the position and function of all controls, as well as with the
machine features shown in the chapter “Operation and Use”
1.4 Warnings
Unauthorized changes and/or modifications to the machine
relieve the manufacturer of any liability for possible damages to
objects or people. Do not remove or make inoperative the safety
devices, this would cause a violation of safety at work laws and
regulations.
Any other use which differs from that provided for by the
manufacturer of the machine is strictly forbidden.
The use of non genuine parts may cause damage to people or
objects
1.5 Scrapping
When your machine’s working life is over and it can no longer be used, it must
be made inoperative by removing any connection to power sources.
These units are considered as special waste material, and should be broken
down into uniform parts and disposed of in compliance with current laws and
regulations. If the packing is not polluting or non-biodegradable, deliver them to
appropriate handling station.

General Information 7
PV-15P
Declaration Of Warranty And Limitation Of Liability
The manufacturer has paid proper attention to the preparation of this manual.
However, nothing contained herein modifies or alters, in any way, the terms
and conditions of manufacturer agreement by which this lift was acquired, nor
increase, in any way, manufacturer’s liability to the customer.
To The Reader
Every effort has been made to ensure that the information contained in this
manual is correct, complete, and up-to date. The manufacturer is not liable for
any mistakes made when drawing up this manual and reserves the right to make
any changes due the development of the product, at any time.

Product Identification 8
PV-15P
Product Identification
The identification data of the machine are shown in the serial plate placed on the
power side column.
The removal of the serial plate is strictly forbidden.
Machines may be updated or slightly modified from an aesthetic point of view
and, as a consequence, they may present different features from these shown,
this without prejudicing what has been described herein.
2.1 Warranty Certificate
The warranty is valid for a period of 12 months starting from the date of the
purchase invoice.
The warranty will come immediately to an end when unauthorized modifications
to the machine or parts of it are carried out.
The presence of defects in workmanship must be verified by the Manufacturer’s
personnel in charge.
2.2 Technical Servicing
For all servicing and maintenance operations not specified or shown in these
instructions, contact your Dealer where the machine has been bought or the
Manufacturer’s Commercial Department.

Packing, Transport, Storage 9
PV-15P
Packing, Transport, Storage
Only skilled personnel who are familiar with the lift and this manual shall be
allowed to carry out packing, lifting, handling, transport and unpacking operations.
3.1 Packing
The packing of the lift is delivered in following components:
• N. 1 base unit packed in a steel frame, wrapped up in non-scratch material,
including the accessory box and the power unit.
The package weight is about 2490 lbs.
Figure 1 – Packages

Packing, Transport, Storage 10
PV-15P
3.2 Lifting And Handling
When loading/unloading or transporting the equipment to the site, be sure to
use suitable loading (e.g. cranes, trucks) and hoisting means. Be sure also to
hoist and transport the components securely so that they cannot drop, taking
into consideration the package’s size, weight and center of gravity, and its fragile
parts.
3.3 Storage And Stacking Of Packages
Packages must be stored in a covered place, out of direct sunlight and in low
humidity, at a temperature between 14°F and 104°F.
3.4 Delivery And Check Of Packages
When the lift is delivered, check for possible damages due to transport and
storage; verify that what is specified in the manufacturer’s confirmation of order
is included. In case of damage in transit, the customer must immediately inform
the carrier of the problem.
Packages must be opened paying attention not to cause damage to people (keep
a safe distance when opening straps) and parts of the lift (be careful the objects
do not drop from the package when opening).

Lift Description 11
PV-15P
Lift Description
The lift is suitable for lifting motor vehicles having maximum weight as described
in the nameplate on the power side column of the lift. All mechanical parts
such as columns, carriages, and lift arms have been built in steel plate to make
the frame stiff and strong while keeping a low weight. The electro hydraulic
operation is described in detail in chapter 8.
This chapter describes the lift’s principal elements, allowing the user to be
familiar with the machine.
As shown in figure 2, the lift is composed of two columns: power-side column
(1) and off-side column (2) with the extension (3) on each, each equipped with
a carriage (4) and a pair of lifting arms (5) with the adaptor (6) anchored to the
ground by means of the column base. The overhead beam (7) is equipped with
the anti-crush safety bar and an overhead cut-off switch for protection of the
vehicle roof. Raising motion is carried out by pushing the lifting button on the
power unit (8), which
delivers the hydraulic
fluid to cylinders
inside the columns.
The mechanical safety
release is carried out
by pushing the lock
release lever (9) on
the power-side column.
Lowering motion is
controlled by pushing
the lowering lever on
the power unit and
carried out under the
weight of the load lifted.
The synchronization
is controlled by the
equalizer cables. The
arm locks can be
engaged automatically
when the lift is raised.
Figure 2 – Lift

Technical Specification 12
PV-15P
Technical Specification
5.1 Size And Main Features
CAPACITY 15,000lbs (6800kg)
Max. lifting height 75 1/8” (1908mm)
Min. lowered height 7 1/4” (183mm)
Overall height - special low setting 152 1/2” (3872mm) Requires purchase of additional shorter cables
Overall height - lower setting 164 7/8” (4187mm)
Overall height – higher setting 176 7/8” (4492mm)
Clearance between columns 123 1/2” (3138mm)
Lifting time 70~90 s
Lowering time with full load 40~60 s
Noise level 75 dB(A)/1m
Working temperature 41°F - 104°F
Average weight of package 2570 lbs (1166 kg)
5.2 Electric Motor
Voltage 208V-240V/50Hz/60Hz/1Ph
Power 3HP
N° Poles 2
Speed 3450 rpm
Motor enclosure type B14
Insulation class IP 54
Motor connection must be carried out referring to the attached wiring diagrams
(fig.6). The motor direction of rotation is shown in the label placed on the motor.
Before use of the lift, make sure to check if the motor specification shown in the
nameplate of the motor conforms to the local electric supply.
5.3 Pump
Type Gear
Flow rate 2.1 cm3/g
Continuous working pressure 225 bar

Technical Specification 13
PV-15P
Figure 3 – Layout

Technical Specification 14
PV-15P
5.4 Hydraulic Power Unit
Figure 4 – Hydraulic Power Unit
5.5 Oil
Use wear proof oil for hydraulic drive, in conformity with ISO 6743/4 rules (HM
class). The oil with features similar to those shown in the table is recommended.
Test standards Features Value
ASTM D 1298 Density 20°C 0.8 kg/l
ASTM D 445 Viscosity 40°C 32 cSt
ASTM D 445 Viscosity 100°C 5.43 cSt
ASTM D 2270 Viscosity index 104 N°
ASTM D 97 Pour point ~ 30 °C
ASTM D 92 Flash point 215 °C
ASTM D 644 Neutralization number 0.5 mg KOH/g
Change hydraulic oil at 1 year intervals

Technical Specification 15
PV-15P
Figure 5 - Hydraulic Plan
1 Oil filter 6 Hydraulic cylinder
2 Gear pump 7 Manual lowering valve
3 Motor 8 Flow restrictor
4 Non return valve 9 Startup valve
5 Pressure overload valve (Max. 250 bar)

Technical Specification 16
PV-15P
Figure 6a – Electrical Diagram (400V/380V/50Hz/60Hz/3Ph)

Technical Specification 17
PV-15P
Figure 6b – Electrical Diagram (220V/50Hz/60Hz/1Ph)

Safety 18
PV-15P
Safety
Read this chapter carefully and completely because it contains important
information for the safety of the operator and the person in charge of maintenance.
The lift has been designed and built for lifting vehicles and
making them stand above level in a closed area. Any other use is
forbidden.
The manufacturer is not liable for possible damages to people,
vehicles or objects resulting from an improper or unauthorized
use of the lift.
For operator and people safety, a square space for a safety area at least 3 feet
free away from the lift must be vacated during lifting and lowering. The lift must
be operated only from the operator’s control site in this safety area.
Operator’s presence under the vehicle, during working, is only admitted when
the vehicle is lifted and the safety lock is engaged.
Never use the lift when safety devices are off-line. People, the
lift and the vehicles lifted can be seriously damaged if these
instructions are not followed.
6.1 General Warnings
The operator and the person in charge of maintenance must follow accident-
prevention laws and rules in force in the country where the lift is installed.
They also must carry out the following:
• Neither remove nor disconnect hydraulic, electric, or other safety devices;
• Carefully follow the safety indications applied on the machine and included
in the manual;
• Observe the safety area during lifting;
• Be sure the motor of the vehicle is off, the gear engaged, and the parking
brake put on;

Safety 19
PV-15P
• Be sure only authorized vehicles are lifted without exceeding the maximum
lifting capacity;
• Verify that no one is on the arms during lifting or standing.
6.2 Safety Device
To avoid overloading and possible breaking, the following safety devices have
been used:
• A pressure overload valve built inside the hydraulic power unit to prevent
excessive weight.
• Mechanical safeties built in each carriage with automatic engagement for
lifting safety.
The pressure overload valve has been preset by the
manufacturer to a proper pressure. DO NOT try to adjust it to
overrun the rated lifting capacity.
It is strictly forbidden to modify any safety device. Always
ensure the safety device for proper operation during the service.

Safety 20
PV-15P
6.3 Safety Signs
All safety warning signs (ref. figure 7) displayed on the lift are with the purpose
to draw the operator’s attention to dangerous or unsafe situations. The labels
must be kept clean and they have to be replaced if detached or damaged. Read
the meaning of the labels carefully and memorize it.
Figure 7 – Safety Signs