Atlas PSP-6000 User manual

Important Information
Introduction
Thoroughly read this manual before operating the lift and comply with the
instructions. Always display the manual in a conspicuous location.
Personal injury and property damage incurred due to non-compliance with these
safety instructions are not covered by the product liability regulations.
Intended Use
This single column vehicle lift is classified as movable model. Movable single
column vehicle lifts are especially useful indoors. It is special equipment
for lifting vehicles, such as cars, to a certain height for maintenance. It is
forbidding to park vehicles underneath. Observe the rated load capacity and load
distribution of the lift.
Safety Instructions for Commissioning
• The lift may be installed and commissioned by authorized service personnel
only.
• The standard lift version may not be installed and commissioned in the
vicinity of explosives or flammable liquids, outdoors, or in moist rooms
(e.g. car wash).
Safety Instructions for Operation
• Read the operating manual.
• Lift operation by authorized personnel over 18 years only.
• Always keep the lift and lift area clean and free of tools, parts, debris etc.
• Once the disk adapters contact the lift points, check arm restraints for
engagement.
• After raising the vehicle briefly, stop and check the disk adapters for secure
contact.
• Always lift the vehicle using all four adapters.

• Make sure the vehicle doors are closed during raising and lowering cycles.
• Closely watch the vehicle and the lift during raising and lowering cycles.
• Do not allow anyone to stay in lift area during raising and lowering cycles.
• Do not allow anyone on lift or inside raised vehicle.
• Only use the lift for its intended purpose.
• Comply with the applicable accident prevention regulations.
• Do not overload the lift. The rated load capacity is indicated on the lift
nameplate.
• Only use the vehicle manufacturer’s recommended lift points.
• After positioning the vehicle apply the parking brake.
• Use caution when removing or installing heavy components (center-of-
gravity displacement).
• The main switch serves as emergency switch. In case of emergency turn to
OFF position.
• Protect all parts of the electrical equipment from humidity and moisture.
• Protect the lift against unauthorized usage by padlocking the main switch.
Safety Instructions for Servicing
• Maintenance or repair work by authorized service personnel only.
• Turn off and padlock the main switch before doing any maintenance, or
repair work.
• Work on pulse generators or proximity switches by authorized service
personnel only.
• Work on the electrical equipment by certified electricians only.
• Ensure that ecologically harmful substances are disposed of only in
accordance with the appropriate regulations.
• Do not use high pressure/steam jet cleaners or caustic cleaning agents.
Risk of damage!
• Do not replace or override the safety devices.
Safety Features
Hold-to-run Type Control
The operator is required to hold the controls in the engaged position to raise or
lower the lift.

Equalizing System
The lift is equipped with distributing and connecting flow valve to ensure level
movement of carriage.
Pipe Break Valve
The hydraulic cylinders are equipped with pipe break valves. They respond in
case of rapid pressure drop (line break) to prevent sudden lowering movements.
Pressure Relief Valve
A pressure relief valve is used to limit the hydraulic working pressure to a
maximum of 200bar.
Disposal Of Used Oil
Used oil, which is removed from the power unit and the plant during an oil
change, must be treated as a polluting product, in accordance with the legal
prescriptions of the country in which the lift is installed.
Machine Demolition
In the event that the machine must be demolished, it must be done by
authorized technicians, just like for assembling. The metallic parts can be
scrapped as iron. In any case, all the materials deriving from the demolition
must be disposed of in accordance with the current standards of the country in
which the rack is installed. Finally, it should be recalled that for tax purposes,
demolition must be documented; submitting claims and documents according
to the current laws in the country in which the rack is installed at the time the
machine is demolished.

Specifications
Lifting
Capacity Max. Lifting Height Overall Dimension Maximum (L*W*H) Noise Weight Voltage
6,000lbs 71 2/3” 111 1/2” x
96” x 102 3/4” <70 dB 1,900 lbs
110V,
1-phase

Transport/Packing/Storage
Only skilled personnel who are familiar with the lift and this manual
shall be allowed to carry out packing, lifting, handling, transport and
unpacking operations.
Packing
90% components were pre-assembled before shipment, and packed with blister
packing in steel frame. Arms, adapters and rubber pads were put in the lift.
Power unit was packed in carton box separately, power unit stand was packed
and fixed on above the lifts.
Lifting And Handling
When loading/unloading or transporting the equipment to the site, be sure to
use suitable loading (e.g. cranes, trucks) and hoisting means. Be sure also to
hoist and transport the components securely so that they cannot drop, taking
into consideration the package’s size, weight and center of gravity and it’s fragile
parts.
Storage And Stacking Of Packages
Packages must be stored in a covered place, out of direct sunlight and in low
humidity, at a temperature between -10°C and +40°C.
Delivery And Check Of Packages
When the lift is delivered, check for possible damages due to transport and
storage; verify that what is specified in the manufacturer’s confirmation of order
is included. In case of damage in transit, the customer must immediately inform
the carrier of the problem.
Packages must be opened paying attention not to cause damage to people (keep
a safe distance when opening straps) and parts of the lift (be careful the objects
do not drop from the package when opening).

Installation Requirements
Working Site
The user should prepare the working site for the lift before its arrival. The lift
must be placed on flat and hard ground, which is made of cement or bricks, with
the load at the position of vertical post of 3t/m2. There should be > about 40”
space around the lifted vehicle, and the net height indoor should be about 12’.
Power Source
Requires a dedicated circuit with 110v and 20 amp breaker.
Tools Required For Install
• Hoist or Forklift or Floor Jack or Cherry Picker
• Metric Sockets and Open Wrench set
• One 10’ to 12’ step ladder
• Thread Seal Tape
• ISO 32 Light Hydraulic Oil (approx. 12 quarts)

Installation Procedure
1. After unloading the lift, place it near the intended installation location.
2. Remove the shipping bands and lay out the pieces to take inventory.

3. Remove packing materials.

4. Hoist the column onto the frame base, lining up the bolt holes.
Optional Turnbuckle Shown

5. Secure the column with the hex head bolts and washers.
6. Raise the carriage by hand. Ready the hex head bolts.

7. Hoist the lifting frame, lining up the bolt holes with the column’s carriage.

8. Secure the lifting frame with the hex head bolts and washers.
9. Slide the off-side arm assembly into the lifting frame and tighten the screw
on top of the lifting frame to secure it.

10. Slide the column-side arms into the lifting frame and tighten the screw on
top of the lifting frame to secure it.
11. Screw the adapter holder onto the column.

12. Unwrap the ball bearing on the wheel assembly.
13. Secure the wheel assembly to the column with the axis pin and tighten set
screw along with jam nut.

14. Install the power unit onto the column with washers and hexagon screws.
Note: Quick connect fitting on the power unit reservoir is not used.

15. Remove existing pipe fitting from hydraulic cylinder
16. Prepare new pipe fitting with O-ring washer and Thread Seal Tape

17. Install new pipe fitting into hydraulic cylinder
18. Connect and tighten the oil hose to the power unit and hydraulic fitting

Operation Instructions
Operation Rules For Mechanism System
The movable single column lift is provided with separate traveling mechanism.
Pump the hauling handle of the steering rear wheel forwards and backwards to
make the vertical column off the ground, then you can push or pull the lift. On
arriving the working site, press the valve handle to retract the wheel, then the
vertical column lands on the ground steadily.
The lift must only be pushed into the vehicle if in line with it. Insert the pallet
under the vehicle beam and the pallet must be in line with the beam.
Retract the rear wheel of vertical post to land the vertical post steadily before
the lift lifts load, and make sure there is no foreign article such as hand tools,
bolts, screw caps, small stones. No lifting during moving!
Operation Flow
1. Vehicle stops in the service position with engine off
2. Turn the handle for hydraulic movable wheel to lift the vertical post base a
bit
3. Push the lift into the underside of vehicle
4. Make sure there is no foreign articles under the base and the ground is level
5. Grasp the valve handle to make the base lowered to ground
6. Align 4 pallets on the lifting arm respectively to the supported positions on
the vehicle underside
7. Press the “” button to raise the vehicle by 10~15 centimeters
8. Stop the vehicle raising and check for safe and secure four high points of
the pallet.
9. Check if the main lifting arm touches the vehicle bottom plate, which should
not occur during normal lifting.
10. Pull the safety unlock handle to make the lifting platform unlocked.