Autel DRAGON FISH User manual

Charger Quick Guide
DRAGON FISH

charging two aircraft batteries and a ground
station at the same time. When it detects that the
aircraft battery voltage difference exceeds a
certain value, the charger will intelligently start the
charge equalization mode. This mode can quickly
balance the voltage of the battery during
charging.
Using the charger
Follow the steps below to charge the aircraft
battery and ground station:
1. Please connect one end of the charger to a
100~240V AC power source, and connect the
other end to the aircraft battery, as shown in the
figure below.
2. If you want to charge the ground station,
pleaseconnect the round head wire on the
charger to the ground station.
When the ground station is charging, the red
light will stay on and the green light will stay
on when it is fully charged.
3. While the aircraft battery is charging, the
charger's green light will stay on, and the LED
light will flash quickly. When charging starts in
equalization mode, the green light will flash
slowly. If charging fails, the indicator will be
static red. Under such circumstances, you
can disconnect the power and try charging again.
Registered Trademark
Shenzhen Autel Robotics Aviation Technology Co.,
Ltd. (hereinafter referred to as "Autel Robotics") has
been registered in China, the United States and in
several overseas countries.EVO IITM, Dragon
FishTM AutelVoyagerTM, StarpointTM and Autel
Robotics® are the registered trademarks of Autel
Robotics. The names of the products and compa
nies mentioned in this manual are trademarks
respectively held by Autel Robotics.
Copyright
Without explicit written consent of Autel Robot-
ics, no part of this manual may be copied or
forwarded in any form or by any means (whether
electronic, mechanical, photocopy, recording or
other means).
Disclaimer
Thank you for purchasing the Autel Robotics
Dragonfish Charger. Please follow the guidelines
in this manual to ensure safe use of the charger.
Only adults 18 years and older are permitted to
use this product. Keep out of reach of children
when not in use.
If you fail to abide by these safety instructions,
Autel Robotics will not provide warranty service
for damages to the product during use, nor will it
be liable for any product damage or loss (whether
direct or indirect, legal, special, accidental or
economical (including but not limited to loss of
profit)) during use. Do not use incompatible parts
or use any method that does not comply with the
official instructions of Autel Robotics to modify
this product.
The safety guidelines outlined in this manual will
show you the steps and methods to safely utilize
the charger. Please ensure that, when using this
product, you do not endanger the personal and
property safety of you and others.
This manual will be updated from time to time. To
download the latest version, please visit
www.autelrobotics.com
Introduction
This charger is a smart charger and is capable of

Warning
To ensure proper heat dissipation,do not
cover the charger when charging.
Always place the charger in a stable and
safe location.
During charging, try to avoid touching the
metal casing of the charger to prevent
high temperature burns.
metal casing of the charger to prevent high
temperature burns.
If the failure cannot be resolved, please
contact your local dealer.
4. When the battery is fully charged, disconnect
the charger from the battery. Moreover, when the
battery is fully charged, the LED indicator status
will signal as follows:
The LED indicator on the aircraft battery will
be off.
Whether the ground station is turned on or
off, the LED indicator on the ground station is
always green.
Specifications
120 minutes
DF_CHARGER
41°F to 113°F (5°C to 45°C)
100-240V (50-60Hz 4A MAX)
*
Model Name
Operating temperature
Input voltage
Output Power
Time required to fully
charge (single battery)
Main output: 1/2/3 26.4V 7A
Total output power: 185W
The time required for a full charge is based on data captured under a laboratory environment and
room temperature. The actual full charge time may vary in real-world environments and surroundings.
*

2018-2019 Autel Robotics Co., Ltd. All Rights Reserved