Autel MaxiVCI V100 User manual

Table of Contents
General Notice ...........................................................1
Introduction .............................................................. 2
Functional Description.............................................. 4
Product Troubleshooting.......................................... 8
Driver Setup .............................................................. 9
Firmware Update ..................................................... 12
Compliance Information ..........................................14
Warranty And Service ..............................................16

1
General Notice
The wireless diagnostic interface MaxiVCI V100 has been carefully designed
and tested to comply with OBDII protocols. However, some vehicle models
are not in full compliance with these protocols for various reasons. In addition,
the computer control systems or sensors on any given vehicle may be
malfunctioning.
While Autel’s testing and the experiences of the users have shown the unit to
be safe and reliable, there is an inherent risk in using any product that may
potentially affect the operation or drive-ability of your vehicle.
If you are concerned about the operation of your vehicle at any time while
using the MaxiVCI V100:
Pull off the roadway immediately or as soon as it is safe to do so.
Disconnect the device from the OBDII port.
Consult a licensed mechanic or automobile service center.
Contact your local distributor, or visit www.autel.com for issues or concerns
about the product. We maintain an active database of the feedback we
receive, and your comments can help us continuously improve the product.

2
Introduction
The wireless diagnostic interface MaxiVCI V100 is a small interface box used
to connect to a vehicle’s diagnostic connector (DLC) and connect wirelessly
with the MaxiSys Display Tablet, as well as standalone PC, as a vehicle
communication interface (VCI) for vehicle data transmission. Thanks to the
wireless BT technology, with which you are allowed to work freely around the
vehicle.
The MaxiVCI V100 can communicate with vehicles’ electronic control units
(ECUs), guaranteeing performance and speed that redefine multi-brand
diagnostics. The development of this interface has been focused on reducing
the communication time, and ensuring the tool is practical to use.
The MaxiSys diagnostic platform combines the MaxiVCI V100 and the display
tablet with technical information into a single program, ensuring quick and
simple access to the vehicle to perform comprehensive diagnostics
applications.

3
Wireless Communication
The MaxiVCI V100 supports BT communication. It can transmit vehicle data to
the MaxiSys Display Tablet without a physical connection. The working range
of the transmitter through BT communication is about 164 feet (about 50 m). A
signal lost due to moving out of range automatically restores itself when the
display unit is brought closer to the MaxiVCI V100 unit.
USB Connectivity
The MaxiVCI V100 also provides a direct connection to the MaxiSys Display
Tablet or a PC via a USB 2.0 full-speed connection. All of the electronics are
contained in the device shell, making it a compact and rugged vehicle
communication tool.
Power Source
The MaxiVCI V100 operates on 12-volt vehicle power, which it receives
through the vehicle data connection port. The unit powers on whenever it is
connected to an OBD II/EOBD compliant data link connector (DLC).
It can also be powered through connection with a PC via the USB cable, so
there’s no need to connect the device to the vehicle when performing firmware
update through the PC.

4
Functional Description
The MaxiVCI V100 device package includes the unit, user manual, and a CD
with driver program and update agent.
1. Lighting Push Button
2. Power LED
3. Vehicle LED
4. Connection LED
5. Vehicle Data Connector (16-Pin)
6. USB Port
Lighting Push Button
Press the lighting push button to turn on the white LED in the vehicle
data connector socket.

5
Status LEDs
There are 3 status LEDs on the front panel of the MaxiVCI V100, which
indicates its working status as well as the hardware conditions, and are very
useful for troubleshooting the device’s communication or connection to the
vehicle, display tablet and/or the PC. See Table 1 for detailed description of
the status LEDs. Table 1 –Status LEDs on the Front Panel
LED
Color
Description
Power
Green
Illuminates solid green when powered on.
Amber
The power LED flashes green and amber automatically when
performing firmware update.
Red
Flashes red when system failure occurs.
Note: The power LED illuminates red automatically every time
when the device is power up, which is a normal self-test
procedure, and it will turn green automatically later when the
device starts working normally.
Vehicle
Green
Flashes green when communicating with the vehicle’s system.
Connection
Green
Illuminates solid green when properly connected with the display
tablet or the PC via the USB cable
Blue
Illuminates solid blue when connected with the display tablet via
wireless (BT) connection
Vehicle Data Connector
The vehicle connector connects the MaxiVCI V100 to the vehicle’s 16-pin DLC
directly.

6
USB Port
The USB port provides the easiest connection between the device and the
display tablet or the PC via a USB cable, and is used to control the device
from the software application running on the PC.
Technical Specifications
Item
Description
Communications
BT V.2.1 + EDR
USB 2.0
Wireless Frequency
2.4 GHz
Input Voltage Range
12 VDC
Supply Current
150 mA @ 12 VDC
Operating Temperature
0°C to 50°C (ambient)
Storage Temperature
-20°C to 70°C (ambient)
Dimensions (L xW x H)
87 mm (3.43”) x 52 mm (2.05”) x 24.5 mm (0.96”)
Weight
0.076 kg (0.168 lb.)
Built-in Battery
3.7V Lithium Battery
Light
White LED
Capabilities
When used in conjunction with the display table or the OEM softwares from
the PC, the MaxiVCI V100 is able to perform the following functions:
Auto diagnostics to read and clear the error memory, to display system
parameters and the status of the ECU;

7
Activation, adjustments and configurations that are essential for ensuring
a complete repair;
Resetting the service lights or the airbag systems;
Configuration of the ECUs, keys and remote controls, etc.

8
Product Troubleshooting
This part describes problems that you may encounter while using the MaxiVCI
V100.
Vehicle Linking Error
A communication error occurs if the MaxiVCI V100 fails to communicate with
the vehicle’s control module when performing diagnostic procedures. You
need to do the following check-ups:
Verify that the ignition is ON.
Check if the device’s vehicle data connector is securely connected to the
vehicle’s DLC.
Turn the ignition off and wait for about 10 seconds. Turn the ignition back
to on and continue the operation.
Verify the control module is not defective.
PC Communication Error
Verify the interface device is powered, and the power LED is illuminated
green.
Check if there is any firewall software interfering with the connection
port.
Check if the green status light is illuminated for USB communication.
If these issues have been addressed, verified, and you are still having trouble,
please contact technical supports for assistance.

9
Driver Setup
In order for the MaxiVCI V100 to operate correctly with the diagnostic
applications on the PC, you will need to first install the device’s driver onto the
PC that controls the device.
The program package requires Windows XP, Windows 7 (32 or 64 bit)，
Windows 8 (32 or 64 bit), or Windows 10 (32 or 64 bit).
IMPORTANT: Do not plug the MaxiVCI V100 onto the PC until you have
installed the driver program.
The following steps may vary depending on the operating system or
components that are installed on your computer, but in general this is the
standard installation process.
1 Insert the included CD into the CD/DVD slot of the PC and open the CD
folder.
2 Double click on “Autel Run.exe”item.
3 Click the MaxiVCI V100 icon in the MaxiSys PC Suite screen.
4 Select the installationlanguage and the driver installation wizard will load
momentarily.
5 Follow the wizard instructions on the screen and click “Next”to continue.