Avaya CU-360 User manual

Avaya CU360
Collaboration Unit
Quick Start Guide

2 3
WHAT’S IN THE BOX
One Remote Control
2 AAA batteries One Rubber Cap
Avaya CU360 Collaboration Unit
WHAT’S IN THE BOX
Wall mount One Power Adapter
220V and 110V with
regional converters
4 screws 4 *40mm
4 plug 6*40mm
1 tripod UNC screw
One HDMI Cable

4 5
Setting Up the Device Video Privacy
NOTE: if you are not using WiFi, make sure to
connect a LAN / Ethernet cable.
CONTROLLING THE CU360:
USING THE WEB
1. When the CU360 is connected to the TV and
your Network, the IP address (X.X.X.X) will be
displayed in the top left corner of the screen.
2. Using a device connected to the same network,
type http://[IP ADDRESS] into the web browser.
3. Enter the default user name of Admin and the
password 1234.
4. A Configuration Wizard will be initiated (only if
the system has not yet been configured).
More details about system configuration can
be found in the CU360 User Guide, available at:
support.avaya.com
3. Plug in the power
adapter.
2. Plug the HDMI cable
into the TV and CU360.
1. Place the CU360
above the TV, and use
its hinge to secure it.
Use the rubber cap
to cover the camera
for privacy
Power SupplyUSB C USB A
EthernetHDMI On / Off
Button
CONNECTING THE CU360 TO THE TV

6 7
CONTROLLING THE CU360:
USING THE REMOTE CONTROL
CONTROLLING THE CU360:
USING THE REMOTE CONTROL
ENTER
BACK
DEL
1 2 3 4 5 6 7 8 9 0
! ? # $ & * )(
_ - + = \
%
: , . [
., :
PG UP ]
“
FN <
/ ;
>HOME ENDPG DWN
CTRL
SHIFT
ESC
CAPS
ALT @
@SPACE
Power Button
Zoom in
Back
OK button
Zoom out
Audio mute / unmute
Decline Call /
Disconnect
Change PiP position
Change layout
Voice activation
Start / Stop Recording
Home
Video mute / unmute
Arrow keys
(Pan Tilt zoomed camera /
navigate)
Battery cover
(push and slide for
opening)
Function key
(enables/disables yellow
digits / symbols)
Increase
volume
Decrease
volume
Control far /
near camera
Delete
Mouse
Arrow keys
(Pan Tilt zoomed
camera / navigate)
Call / Accept
Call
Start / Stop
presentation

8 9
PAIRING THE REMOTE CONTROL
Your remote control is a wireless control device,
pre-paired with your CU360 unit. If you are using
a new optional remote control, or your remote
control is not paired, please follow the below
procedure.
1. Check that the remote control is equipped
with 2 AAA charged batteries.
2. Unplug the codec unit from power.
3. Press the Back key and the OK key
together, until the small blue LED on
top of the remote quickly flashes a
few times.
4. While the LED light is still flashing, plug the
codec unit into power while keeping the
remote control close to the unit. The remote
control led should stop flashing to show
successful pair.
5. If the pairing fails, disconnect all the cables
from the CU, including USB and repeat the
procedure.
USE THE REMOTE CONTROL
The remote control provided in the box is pre-
paired. Please ensure that the batteries are
inserted inside the remote control wireless device.
If a new remote is used, out of the box, please
follow the pairing procedure reported in next
section of this guide.

10 11
1. Select your language and select Next.
2. If you received an auto provisioning service
code, enter it and select Next.
3. Otherwise, just select Next to continue with
the manual setup process. - Enable Configure > General >
Advanced Settings = Yes
- Select Configure > Advanced
(default PIN is 1234)
- Select Configure > Advanced > System >
Security > Settings > Bluetooth
- Turn on the Bluetooth on your CU360.
To add the optional Avaya B109 as Bluetooth
microphone for the Avaya CU360, please follow
these steps.
1. OnAvaya CU360
CU360 SETUP: AUTO PROCESS B109 SETUP:
CU360 SETUP: MANUAL PROCESS
Please complete the following steps, select Next
after completing each item.
1. Configure System Name, Country, Preferred
Language and Desired Protocol.
2. Configure Network Settings.
3. Configure Gatekeeper (if H.323 is enabled).
4. Configure SIP Server (if SIP is enabled).
2. Hold down for two seconds on the Avaya
B109. This makes the B109 visible to CU360.
The icon is displayed on your B109 and
the LEDs flash blue.

12 13
3. In the selected Bluetooth settings window
of the CU360, the Avaya B109 will appear in
the list of the available devices. Select the
Avaya B109 from the list of devices and select
pairing. It may take awhile for the devices to
find one another. The devices are paired and
usually automatically connect to one another.
The icon is displayed on the B109.
4. After 60 seconds in pairing mode, the B109
returns to normal mode even if pairing has
not been established.
IMPORTANT NOTICE
Read all safety, installation, and user documentation
prior to installing or operating this product.
To view and download safety, installation, and user
documentation go to Avaya’s support web site at
support.avaya.com. Check this site frequently for
any updates.
© 2019 Avaya Inc. All Rights Reserved. Avaya and the Avaya logo are trademarks
of Avaya Inc. and are registered in the United States and other countries. All other
trademarks identified by ®, TM, or SM are registered marks, trademarks, and service
marks, respectively, of Avaya Inc. 01/19 •CU360 QSG

P/N 700514085 A03