Avdel 7340 User manual

I n s t r u c t i o n M a n u a l
Pass onto user to read and keep for reference
Hydro-Pneumatic Power Tool
0734 type
07340 - 07344 - 07345
07346 - 07347 - 07348 models
0734
TYPE

AIR PRESSURE Minimum - Maximum 4.8 - 7 bar 70 - 100 lbf/in2
FREE AIR VOLUME REQUIRED @ 5.5 bar / 80 lbf/in21.59 litres .056 ft3
STROKE Minimum 16 mm .625 in
PULL FORCE @ 4.8 bar / 70 lbf/in210.91 kN 2450 lbf
CYCLE TIME Approximately 1.5 seconds
NOISE LEVEL 73.4 dB(A)
WEIGHT Without nose equipment 1.66 kg 3.65 lb
VIBRATION 2.55 m/s2
AVDEL policy is one of continuous development. Specifications shown in this document may be subject to changes which
may be introduced after publication. For the latest information always consult Avdel.
■
■
■
■
■
■
■
■
S P E C I F I C A T I O N S F O R 0 7 3 4 T Y P E T O O L
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■

General 2
Specific to Type of Tool 3
General 4
07340 Tool Dimensions/Selection 4-5
07344 Tool Dimensions/Selection 5
07345 Tool Dimensions/Selection 6
07346 Tool Dimensions/Selection 7
07347 Tool Dimensions/Selection 8
07348 Tool Dimensions/Selection 9
Air Supply 10
Operating Procedure 10
Accessories 11
07340/4/7/8 Fitting/Servicing/Components 12-14
07345/6 Fitting/Servicing/Components 15-16
Regular Servicing - Service Kit 18-19
Maintenance 20-21
General Assembly & Parts List 22-27
Priming Oil Details 28
Priming Procedure 28-29
Fault Diagnosis Table 30
CO N T E N T S
1
S A F E T Y
I N T E N T O F U S E
P U T T I N G I N T O S E R V I C E
N O S E A S S E M B L I E S
S E R V I C I N G
P R I M I N G
F A U L T D I A G N O S I S

SA F E T Y
2
This instruction manual must be read with particular attention to the following safety rules,
by any person installing, operating or servicing this tool.
DO NOT USE OUTSIDE THE DESIGN INTENT.
DO NOT USE EQUIPMENT WITH THIS TOOL/MACHINE OTHER THAN THAT
RECOMMENDED AND SUPPLIED BY AVDEL.
ANY MODIFICATION UNDERTAKEN BY THE CUSTOMER TO THE TOOL/MACHINE,
NOSE ASSEMBLIES, ACCESSORIES OR ANY EQUIPMENT SUPPLIED BY AVDEL OR THEIR
REPRESENTATIVES, SHALL BE THE CUSTOMER'S ENTIRE RESPONSIBILITY. AVDEL WILL BE
PLEASED TO ADVISE UPON ANY PROPOSED MODIFICATION.
THE TOOL/MACHINE MUST BE MAINTAINED IN A SAFE WORKING CONDITION AT
ALL TIMES AND EXAMINED AT REGULAR INTERVALS FOR DAMAGE AND FUNCTION BY
TRAINED COMPETENT PERSONNEL. ANY DISMANTLING PROCEDURE SHALL BE
UNDERTAKENONLYBYPERSONNELTRAINEDINAVDELPROCEDURES.DONOTDISMANTLE
THISTOOL/MACHINEWITHOUTPRIORREFERENCETOTHEMAINTENANCEINSTRUCTIONS.
CONTACT AVDEL WITH YOUR TRAINING REQUIREMENTS.
THE TOOL/MACHINE SHALL AT ALL TIMES BE OPERATED IN ACCORDANCE WITH
RELEVANT HEALTH AND SAFETY LEGISLATION. IN THE U.K. THE “HEALTH AND SAFETY AT
WORK ETC. ACT 1974” APPLIES. ANY QUESTION REGARDING THE CORRECT OPERATION
OF THE TOOL/MACHINE AND OPERATOR SAFETY SHOULD BE DIRECTED TO AVDEL.
THE PRECAUTIONS TO BE OBSERVED WHEN USING THIS TOOL/MACHINE MUST BE
EXPLAINED BY THE CUSTOMER TO ALL OPERATORS.
ALWAYS DISCONNECT THE AIRLINE FROM THE TOOL/MACHINE INLET BEFORE
ATTEMPTING TO ADJUST, FIT OR REMOVE A NOSE ASSEMBLY.
DONOT OPERATEA TOOL/MACHINETHAT ISDIRECTED TOWARDSANY PERSON(S).
ALWAYS ADOPT A FIRM FOOTING OR A STABLE POSITION BEFORE OPERATING THE
TOOL/MACHINE.
ENSURE THAT VENT HOLES DO NOT BECOME BLOCKED OR COVERED AND THAT
HOSES ARE ALWAYS IN GOOD CONDITION.

3
In addition to the general safety rules opposite, the following specific safety points must also
be observed:
THE OPERATING PRESSURE SHALL NOT EXCEED 7 BAR - 100 LBF/IN2.
DO NOT OPERATE THE TOOL WITHOUT FULL NOSE EQUIPMENT IN PLACE. 07345
AND 07346 TOOLS SHOULD NOT BE OPERATED IF THE GUARD IS DAMAGED IN ANY
WAY.
CARE SHALL BE TAKEN TO ENSURE THAT SPENT STEMS ARE NOT ALLOWED TO
CREATE A HAZARD.
07340, 07344, 07347 AND 07348 TOOLS MUST BE FITTED WITH AN UNDAMAGED
PINTAIL DEFLECTOR OR STEM CATCHER BEFORE OPERATING.
IF THE 0734 TOOL IS FITTED WITH A PINTAIL DEFLECTOR AND IS USED IN THE
VERTICAL NOSE DOWNWARD POSITION, THE PINTAIL DEFLECTOR SHOULD BE ROTATED
UNTIL THE APERTURE IS FACING AWAY FROM THE OPERATOR AND OTHER PERSON(S)
WORKING IN THE VICINITY.
WHEN USING THE TOOL, THE WEARING OF SAFETY GLASSES IS REQUIRED BOTH BY
THE OPERATOR AND OTHERS IN THE VICINITY TO PROTECT AGAINST RIVET EJECTION,
SHOULD A FASTENER BE PLACED ‘IN AIR’. WE RECOMMEND WEARING GLOVES IF THERE
ARE SHARP EDGES OR CORNERS ON THE APPLICATION.
TAKE CARE TO AVOID ENTANGLEMENT OF LOOSE CLOTHES, TIES, LONG HAIR,
CLEANING RAGS ETC… IN THE MOVING PARTS OF THE TOOL WHICH SHOULD BE KEPT
DRY AND CLEAN FOR BEST POSSIBLE GRIP.
WHEN CARRYING THE TOOL FROM PLACE TO PLACE KEEP HANDS AWAY FROM THE
TRIGGER/LEVER TO AVOID INADVERTENT START UP.
EXCESSIVECONTACT WITHHYDRAULIC OIL SHOULD BE AVOIDED.TO MINIMIZETHE
POSSIBILITY OF RASHES, CARE SHOULD BE TAKEN TO WASH THOROUGHLY.

The hydro-pneumatic 0734 type tool is designed to place Avdel breakstem rivets at high speed making it ideal for batch or flow-line
assembly in a wide variety of applications throughout all industries.
There are six different models of this type of tool. Select the one most suited to your application requirements or environment.
The 07340 fitted with a pintail deflector is the standard tool for which a stem catching option is available (see accessories
page 11). It is also possible to order the base tool only (part number 07340-00200) which will not be fitted with a nose assembly.
The base tool part number for the 07344/07345/07346 models is also 07340-00200. The base tool part number for the 07347 is
07347-00200 and for the 07348 is 07348-00200. Differences between the base tools are shown on the general assembly drawings
pages 22 to 27.
4
IN T E N T O F U S E
07340 TOOL SELECTION
FASTENER NOSE (see drawing opposite for A & B)
MATERIAL/DETAILØCOMPLETE
TOOL PART Nº
NOSE ASSY PART NºA (mm)
NAME & HEAD B (mm) A (in)
Al. Alloy
Al. Alloy
Al. Alloy
Steel
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Steel
Al.Alloy
Al. Alloy
Al. Alloy
Steel
Al. Alloy
L/flange
Steel
Al.Alloy & Steel
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Stainless Steel
Stainless Steel
Al. Alloy
Steel
Al. Alloy
Steel
A. Alloy
Steel
Al. Alloy
Al. Alloy
Stainless Steel
Stainless Steel
Steel
Steel
Steel
Steel
Steel
Steel
AVEX
Snap head
& 120°csk
head except
07340-00019
large flange
only.
MONOBOLT
BULBEX
AVSEAL
TLR
AVINOX
AVEX
Snap head
& 120°csk head
Forward stem
release
BULBEX
Forward stem release
AVINOX
Forward stem release
T-LOK
AVIBULB
1/8
"
3 mm
5/32
"
3/16
"
3/16
"
5/32
"
3/16
"
4mm
5mm
6mm
6.5mm
7mm
3/16
"
1/8
"
5/32
"
1/8
"
5/32
"
3/16
"
5/32
"
3/16
"
1/8
"
5/32
"
4.3mm
3/16
"
1/8
"
5/32
"
07340-00001
07340-00002
07340-00003
07340-00008
07340-00006
07340-00008
07340-00009
07340-00010
07340-00015
07340-00015
07340-00016
07340-00017
07340-00018
07340-00019
07340-00036
07340-00031
07340-00008
07340-00009
07340-00015
07340-00016
07340-00064
07340-00074
07340-00065
07340-00075
07340-00066
07340-00076
07340-00062
07340-00072
07340-00067
07340-00077
07340-00058
07340-00008
07340-00015
07340-00037
07340-00038
07340-00038
07340-00039
07340-00039
07340-00040
07340-00038
07340-00039
07340-00038
07340-00039
07340-00015
07340-00014
07340-00015
07340-00014
07340-00008
07340-00015
07490-00900
07490-01000
07490-04100
07490-01600
07490-01400
07490-01600
07490-01700
07490-04200
07490-02300
07490-02300
07490-02400
07490-04300
07490-04900
07490-05000
07340-07300
07498-04500
07490-01600
07490-01700
07490-02300
07490-02400
07340-07600
07498-08400
07640-02100
07640-03100
07640-02200
07640-03200
07640-08300
07498-09100
07640-02200
07640-03400
07498-01600
07490-01600
07490-02300
07381-04500
07381-04600
07381-04600
07381-04700
07381-04700
07381-04800
07381-04600
07381-04700
07381-04600
07381-04700
07490-02300
07241-07300
07490-02300
07241-07300
07490-01600
07490-02300
12.7
9.5
12.7
12.7
12.7
12.7
9.5
12.7
12.7
12.7
9.5
12.7
12.7
19.0
9.5
12.7
12.7
9.5
12.7
9.5
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
9.5
12.7
9.5
12.7
12.7
Standard
Extended
Head Forming
Standard
Extended
Standard
Extended
Head Forming
Standard
Standard
Extended
Head Forming
Standard
Standard
Extended
Standard
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Extended
Standard
Extended
Standard
Standard
3.3
12.9
3.3
3.3
3.3
3.3
11.4
3.3
3.3
3.3
10.0
4.1
3.3
4.1
11.8
4.1
3.3
11.4
3.3
10.0
4.5
6.7
4.5
6.7
5.3
7.2
5.3
7.2
5.3
7.2
4.1
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
10.0
3.3
10.0
3.3
3.3
.500
.375
.500
.500
.500
.500
.375
.500
.500
.500
.375
.500
.500
.750
.375
.500
.500
.375
.500
.375
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.375
.500
.375
.500
.500
.130
.510
.130
.130
.130
.130
.450
.130
.130
.130
.395
.160
.130
.162
.465
.160
.130
.450
.130
.395
.177
.264
.177
.264
.208
.283
.208
.283
.208
.283
.160
.130
.130
.130
.130
.130
.130
.130
.130
.130
.130
.130
.130
.130
.395
.130
.395
.130
.130
B (in)
NOSE TIP TYPE
Minimum Pressure required 5.1 BAR / 75 lbf/in25.4 BAR / 80 lbf/in26.1 BAR / 90 lbf/in2

The 07340 and 07344 are fitted with
fixed straight nose assemblies suitable
where access is unrestricted.
Use the selection charts below and oppo-
site to select a complete 07340 or 07344
tool which will include the correct nose
assembly for a selected fastener. For de-
tailsofNoseAssembliesseepages12and
13.
‘A’ and ‘B’ dimensions will help you as-
sess the accessibility of your application.
07340 & 07344 - FIXED NOSE ASSEMBLY
5
23
.90
A
0734
3.5
89
2.7
68
6.14
156
1.90
48
12.5
317
12.5°
76
2.99
B
31.7Ø
1.25Ø
19
.75
07344 TOOL SELECTION
FASTENER NOSE (see drawing above for A & B)
MATERIAL/DETAILØ
COMPLETE
TOOL PART Nº
NOSE ASSY PART NºA(mm)
NAME &HEAD B(mm) A(in)
Stainless Steel
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy oversize
Al. Alloy
Stainless Steel
Al. Alloy
Al. Alloy oversize
Al. Alloy
Stainless Steel
Al. Alloy
Hybrid oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Hybrid oversize
Al. Alloy
Stainless Steel
Al All
AVDEL
Snap head
& 100°csk
& 120°csk
MBC
Universal head
& 100°csk
L\C MBC
Universal head
& 100°csk
L\C
1/8
"
5/32
"
3/16
"
1/8
"
5/32
"
3/16
"
1/8
"
5/32
"
3/16
"
1/8
"
07344-00003
07344-00005
07344-00007
07344-00010
07344-00012
07344-00013
07344-00019
07344-00020
07344-00045
07344-00054
07344-00051
07344-00046
07344-00052
07344-00055
07344-00053
07344-00037
07344-00033
07344-00057
07344-00037
07344-00034
07344-00034
07344-00058
07344-00035
07344-00023
07344-02100
07344-02300
07344-02900
07344-02400
07344-02600
07344-03000
07344-02700
07344-03100
07498-02400
07498-07000
07498-06700
07498-02500
07498-06800
07344-03200
07498-06900
07344-04700
07498-07600
07498-07300
07344-04700
07344-05100
07344-05100
07344-05300
07498-07800
07344-06000
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Extended
Standard
dd
3.3
2.5
2.5
2.5
2.5
2.5
2.5
2.5
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.130
.100
.100
.100
.100
.100
.100
.100
.187
.187
.187
.187
.187
.187
.187
.187
.187
.187
.187
.187
.187
.187
.187
.187
B(in)
NOSE TIP TYPE
Dimensions shown in bold are millimetres.
Other dimensions are in inches.

07345 - STRAIGHT SWIVEL NOSE ASSEMBLY
The07345isfittedwith a“straight”swivel
type of nose assembly for use on
applications with restricted access.
It will place all the fasteners listed in the
selection table below. Use this table to
select a complete 07345 tool which will
include the correct nose assembly for a
selected fastener. For details of Nose
Assemblies see pages 15 and 16 .
‘A’and ‘B’dimensionswill helpyou assess
the accessibility of your application.
6
0734
3.5
89
2.7
68
6.14
156
1.90
48
.79
20.1
12.5
317
12.5°
234
9.2
55.6
2.18 11.1
.437
76
2.99
91.9
3.61
B
A
6.4 (.25)
360°rotation
about centre line
31.7Ø
1.25Ø
19
.75
Dimensions shown in bold are millimetres.
Other dimensions are in inches.
07345 TOOL SELECTION
FASTENER NOSE (see drawing above for A & B)
MATERIAL/DETAILØ
COMPLETE
TOOL PART Nº
NOSE ASSY PART NºA (mm)
NAME & HEAD B (mm) A (in)
Al. Alloy
Steel
Al. Alloy
Steel
Al. Alloy
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Stainless Steel
Al. Alloy oversize
Al. Alloy
Stainless Steel
Al. Alloy oversize
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Stainless Steel
Stainless Steel
AVEX
Snap head
& 120°csk
head
AVDEL
Snap head
& 100°csk
& 120°csk
MBC
Universal head
& 100°csk
BULBEX
AVSEAL
AVINOX
1/8
"
5/32
"
3/16
"
1/8
"
5/32
"
3/16
"
3/32
"
1/8
"
5/32 "
3/16 "
5/32
"
3/16 "
4mm
5mm
1/8
"
5/32 "
07345-00004
07345-00005
07345-00005
07345-00006
07345-00006
07345-00014
07345-00017
07345-00024
07345-00015
07345-00018
07345-00016
07345-00019
07345-00023
07345-00051
07345-00051
07345-00054
07345-00052
07345-00052
07345-00055
07345-00053
07345-00005
07345-00006
07345-00064
07345-00074
07345-00065
07345-00075
07345-00005
07345-00006
07345-03000
07345-03100
07345-03100
07345-03200
07345-03200
07345-03300
07494-03600
07494-03000
07345-03400
07494-03700
07345-03500
07494-03800
07494-03400
07345-04000
07345-04000
07345-04300
07345-04100
07345-04100
07345-04400
07345-04200
07345-03100
07345-03200
07494-06000
07494-06600
07494-06100
07494-06700
07345-03100
07345-03200
7.87
7.87
7.87
7.87
7.87
5.08
5.08
5.08
6.6
6.6
8.13
8.13
5.08
4.75
4.75
4.75
6.35
6.35
6.35
7.92
7.87
7.87
6.35
6.35
7.62
7.62
7.87
7.87
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Extended
Standard
Extended
Standard
Standard
3.81
3.81
3.81
3.81
3.81
1.17
1.17
3.81
0.84
0.84
0.25
0.25
1.27
2.40
2.40
2.40
2.40
2.40
2.40
2.40
3.81
3.81
1.95
4.11
2.00
4.11
3.81
3.81
.310
.310
.310
.310
.310
.200
.200
.200
.260
.260
.320
.320
.200
.187
.187
.187
.250
.250
.250
.312
.310
.310
.250
.250
.300
.300
.310
.310
.150
.150
.150
.150
.150
.046
.046
.150
.033
.033
.010
.010
.050
.094
.094
.094
.094
.094
.094
.094
.150
.150
.077
.162
.079
.162
.150
.150
B (in)
NOSE TIP TYPE

The 07346 is fitted with a “right angle”
swivel type of nose assembly for use on
applications with no direct access to the
fixing point.
It will place all the fasteners listed in the
selection table below. Use this table to
select a complete 07346 tool which will
include the correct nose assembly for a
selected fastener. For details of Nose
Assemblies see pages 15 and 16 .
‘A’and ‘B’ dimensionswillhelp you assess
the accessibility of your application.
7
07346 - RIGHT ANGLE SWIVEL NOSE ASSEMBLY
2.7
68
31.7Ø
1.25Ø
19
.75
20
.79
0734
3.5
89
6.14
156
1.90
48
12.5
317
12.5°
227
8.93
76
3.0 11.1
.437
BA52
2.06 56
2.19
32
1.26
7.6
.3
2.93
74
97
3.81
360°rotation
about centre line
Dimensions shown in bold are millimetres.
Other dimensions are in inches.
07346 TOOL SELECTION
FASTENER NOSE (see drawing above for A & B)
MATERIAL/DETAILØ
COMPLETE
TOOL PART Nº
NOSE ASSY PART NºA (mm)
NAME & HEAD B (mm) A (in)
Al. Alloy
Steel
Al. Alloy
Steel
Al. Alloy
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy &
Stainless Steel
Al. Alloy oversize
Al. Alloy &
Stainless Steel
Al. Alloy oversize
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Stainless Steel
Stainless Steel
AVEX
Snap head
& 120°csk
head
AVDEL
Snap head
& 100°csk
& 120°csk
MBC
Universal head
& 100°csk
BULBEX
AVSEAL
AVINOX
1/8
"
5/32
"
3/16
"
1/8
"
5/32
"
3/16
"
3/32
"
1/8
"
5/32 "
3/16 "
5/32
"
3/16 "
4mm
5mm
1/8
"
5/32 "
07346-00004
07346-00005
07346-00005
07346-00006
07346-00006
07346-00014
07346-00017
07346-00024
07346-00015
07346-00018
07346-00016
07346-00019
07346-00023
07346-00051
07346-00051
07346-00054
07346-00052
07346-00052
07346-00055
07346-00053
07346-00005
07346-00006
07346-00064
07346-00074
07346-00065
07346-00075
07346-00005
07346-00006
07346-03000
07346-03100
07346-03100
07346-03200
07346-03200
07346-03300
07495-03600
07495-03000
07346-03400
07495-03700
07346-03500
07495-03800
07495-03400
07346-04000
07346-04000
07346-04300
07346-04100
07346-04100
07346-04400
07346-04200
07346-03100
07346-03200
07495-04000
07495-04700
07494-04100
07495-04800
07346-03100
07346-03200
7.87
7.87
7.87
7.87
7.87
5.08
5.08
5.08
6.6
6.6
8.13
8.13
5.08
4.75
4.75
4.75
6.35
6.35
6.35
7.92
7.87
7.87
6.35
6.35
7.62
7.62
7.87
7.87
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Extended
Standard
Extended
Standard
Standard
3.81
3.81
3.81
3.81
3.81
1.17
1.17
3.81
0.84
0.84
0.25
0.25
1.27
2.40
2.40
2.40
2.40
2.40
2.40
2.40
3.81
3.81
1.95
4.11
2.00
4.11
3.81
3.81
.310
.310
.310
.310
.310
.200
.200
.200
.260
.260
.320
.320
.200
.187
.187
.187
.250
.250
.250
.312
.310
.310
.250
.250
.300
.300
.310
.310
.150
.150
.150
.150
.150
.046
.046
.150
.033
.033
.010
.010
.050
.094
.094
.094
.094
.094
.094
.094
.150
.150
.077
.162
.079
.162
.150
.150
B (in)
NOSE TIP TYPE

8
07347 - VACUUM EXTRACTION
The 07347 has an in-built, vacuum stem extractor for use where
gravity feed would be unsuitable. The tool is fitted with a fixed,
straight nose assembly.
Use the selection chart below to select a complete 07347 tool which
will include the correct nose assembly for a selected fastener. For
details of Nose Assemblies see pages 12 to 14.
‘A’ and ‘B’ dimensions will help you assess the accessibility of your
application.
Dimensions shown in bold are millimetres.
Other dimensions are in inches.
0734
3.5
89
2.7
68
6.14
156
2.5
63.5
1.90
48
12.5
317
12.5°
76
2.99 117.5
4.62
23
.90
B
A
31.7Ø
1.25Ø
19
.75
63.5
2.5
Minimum Pressure required 5.1 BAR / 75 lbf/in25.4 BAR / 80 lbf/in26.1 BAR / 90 lbf/in2
07347 TOOL SELECTION
FASTENER NOSE (see drawing above for A & B)
MATERIAL/DETAILØ
COMPLETE
TOOL PART Nº
NOSE ASSY PART NºA (mm)
NAME & HEAD B (mm) A (in)
Al. Alloy
Al. Alloy
Al. Alloy
Steel
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Steel
Al. Alloy
Al. Alloy
Al. Alloy
Steel
Al. Alloy
L.Flange
Al.Alloy & Steel
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
-
-
-
-
Stainless Steel
Stainless Steel
Al. Alloy
Al. Alloy oversize
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Steel
Steel
AVEX
Snap head
& 120°csk
head except
07347-00019
large flange
only
MONOBOLT
BULBEX
AVSEAL
TLR
T-LOK
Snap head
AVINOX
AVDEL
Snap head &
100°csk &
120°csk
MBC
Universal head &
100°csk
AVIBULB
Low profile
1/8
"
3mm
5/32
"
3/16
"
3/16
"
5/32
"
3/16
"
4mm
5mm
6mm
6.5mm
7mm
3/16
"
4.3mm
3/16
"
1/8
"
5/32
"
1/8
"
5/32
"
3/16
"
1/8
"
5/32
"
3/16
"
1/8
"
5/32
"
07348-00001
07347-00002
07347-00003
07347-00008
07347-00006
07347-00008
07347-00009
07347-00010
07347-00015
07347-00015
07347-00016
07347-00017
07347-00018
07347-00019
07347-00031
07347-00008
07347-00009
07347-00015
07347-00016
07347-00064
07347-00074
07347-00065
07347-00075
07347-00066
07347-00076
07347-00062
07347-00072
07347-00067
07347-00077
07347-00058
07347-00013
07347-00014
07347-00013
07347-00014
07347-00008
07347-00015
07347-00024
07347-00026
07347-00030
07347-00029
07347-00028
07347-00034
07347-00035
07347-00051
07347-00054
07347-00045
07347-00052
07347-00055
07347-00046
07347-00053
07347-00008
07347-00015
07347-03000
07490-01000
07347-03400
07347-03200
07347-03100
07347-03200
07490-01700
07347-03500
07347-03300
07347-03300
07490-02400
07347-03600
07381-04800
07490-05000
07498-04500
07347-03200
07490-01700
07347-03300
07490-02400
07340-07600
07498-08400
07640-02100
07640-03100
07640-02200
07640-03200
07340-08300
07498-09100
07640-02400
07640-03400
07498-01600
07241-07400
07241-07300
07241-07400
07241-07300
07347-03200
07347-03300
07344-02300
07344-02900
07344-02600
07344-03000
07344-02400
07344-02700
07344-03100
07498-06700
07498-07000
07498-02400
07498-06800
07344-03200
07498-02500
07498-06900
07347-03200
07347-03300
12.7
9.50
12.7
12.7
12.7
12.7
9.5
12.7
12.7
12.7
9.5
12.7
12.7
19.00
12.7
12.7
9.5
12.7
9.5
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
9.5
12.7
9.5
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
Standard
Extended
Head Forming
Standard
Standard
Standard
Extended
Head Forming
Standard
Standard
Extended
Head Forming
Standard
Standard
Standard
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Standard
Extended
Standard
Extended
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
3.3
12.9
3.3
3.3
3.3
3.3
11.4
3.3
3.3
3.3
10.0
4.11
3.3
4.11
4.11
3.3
11.4
3.3
10.0
4.5
6.7
4.5
6.7
5.3
7.2
5.3
7.2
5.3
7.2
4.1
3.3
10.0
3.3
10.0
3.3
3.3
2.5
2.5
2.5
2.5
2.5
2.5
2.5
4.7
4.7
4.7
4.7
4.7
4.7
4.7
3.3
3.3
.500
.375
.500
.500
.500
.500
.375
.500
.500
.500
.375
.500
.500
.750
.500
.500
.375
.500
.375
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.375
500
.375
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.130
.510
.130
.130
.130
.130
.450
.130
.130
.130
.395
.160
.130
.160
.160
.130
.456
.130
.395
.177
.264
.177
.264
.208
.283
.208
.283
.208
.283
.160
.130
.395
.130
.395
.130
.130
.100
.100
.100
.100
.100
.100
.100
.187
.187
.187
.187
.187
.187
.187
.130
.130
B (in)
NOSE TIP TYPE

07348 TOOL SELECTION
FASTENER NOSE (see drawing above for A & B)
MATERIAL/DETAILØCOMPLETE
TOOL PART Nº
NOSE ASSY PART NºA (mm)
NAME & HEAD B (mm) A (in)
Al. Alloy
Al. Alloy
Steel
Al. Alloy
Al. Alloy
Steel
Al. Alloy
Al. Alloy
Al. Alloy
Steel
Al. Alloy
L/flange
Al.Alloy & Steel
-
-
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Al. Alloy
Stainless Steel
Stainless Steel
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy oversize
Stainless Steel
Al. Alloy
Al. Alloy
Copper
Copper Nickel Al.
Al. Alloy
Copper
Copper Nickel Al.
Al. Alloy
Copper
Copper Nickel Al.
Al. Alloy
Steel
Steel
Steel
AVEX
Snap head
& 120°csk
head except
07348-00019
large flange
only
MONOBOLT
BULBEX
AVSEAL
TLR
AVINOX
AVDEL
Snap head
& 100°csk
& 120°csk
MBC
Universal head
& 100°csk
AVDEL SR
Raised Head
& 120°csk
AVIBULB
Low profile
T-LOK
1/8
"
5/32
"
3mm
3/16
"
3/16
"
5/32
"
3/16
"
4mm
5mm
6mm
6.5mm
7mm
3/16
"
1/8
"
5/32
"
1/8
"
5/32
"
3/16
"
1/8
"
5
/
32
"
3/16
"
1
/
8
"
5
/
32
"
3
/
16
"
1
/
4
"
1/8
"
5/32
"
4.3mm
07348-00001
07348-00003
07348-00008
07348-00008
07348-00010
07348-00015
07348-00006
07348-00015
07348-00017
07348-00018
07348-00019
07348-00008
07348-00015
07348-00008
07348-00064
07348-00074
07348-00065
07348-00075
07348-00066
07348-00076
07348-00062
07348-00072
07348-00067
07348-00077
07348-00058
07348-00008
07348-00015
07348-00024
07348-00026
07348-00025
07348-00030
07348-00029
07348-00028
07348-00034
07348-00035
07348-00051
07348-00054
07348-00045
07348-00052
07348-00055
07348-00046
07348-00053
07498-00001
07498-00001
07498-00001
07498-00008
07498-00008
07498-00008
07498-00004
07498-00004
07498-00004
07498-00026
07348-00009
07348-00015
07348-00015
07348-00800
07348-04100
07348-06800
07348-06800
07348-04200
07348-02300
07348-01400
07348-02300
07348-04300
07348-04900
07348-05000
07348-04500
07348-06800
07348-02300
07348-06600
07348-06700
07348-02100
07348-03100
07348-02200
07348-03200
07348-08300
07348-09100
07348-02600
07348-03400
07348-02500
07348-06800
07348-02300
07348-05100
07348-05400
07348-04800
07348-05200
07348-05500
07348-05700
07348-05300
07348-05600
07348-05800
07348-06100
07348-06300
07348-05900
07348-06200
07348-06400
07348-06000
07490-00900
07490-00900
07490-00900
07490-01600
07490-01600
07490-01600
07498-03900
07498-03900
07498-03900
07490-04900
07348-01600
07348-02300
07348-02300
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
19.00
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
12.7
61
61
61
61
61
61
61
61
61
61
12.7
12.7
12.7
Standard
Hd. Forming
Standard
Standard
Hd. Forming
Standard
Standard
Standard
Hd. Forming
Standard
Standard
Standard
Standard
Standard
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Extended
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
4.1
3.3
4.1
4.1
3.3
3.3
4.5
6.7
4.5
6.7
5.3
7.2
5.3
7.2
5.3
7.2
4.1
3.3
3.3
2.5
2.5
3.4
2.5
2.5
2.5
2.5
2.5
4.7
4.7
4.7
4.7
4.7
4.7
4.7
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
.500
.375
.500
.500
.500
.500
.500
.500
.500
.500
.750
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
500
.500
.500
.500
.500
.500
.500
.500
.500
.500
.500
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
.500
.500
.500
.130
.130
.130
.130
.130
.130
.130
.130
.160
.130
.160
.160
.130
.130
.177
.264
.177
.177
.208
.283
.208
.283
.208
.208
.160
.130
.130
.100
.100
.132
.100
.100
.100
.100
.100
.187
.187
.187
.187
.187
.187
.187
.130
.130
.130
.130
.130
.130
.130
.130
.130
.130
.130
.130
.130
B (in)
NOSE TIP TYPE
07348 - FORCED AIR EVACUATION
9
The 07348 has an in-built, forced air stem evacuation system for use
where gravity feed would be unsuitable. The tool is fitted with a fixed
straight nose assembly.
Use the selection chart below to select a complete 07348 tool which
will include the correct nose assembly for a selected fastener. For
details of Nose Assemblies see pages 12 to 14.
‘A’ and ‘B’ dimensions will help you assess the accessibility of your
application.
Dimensions shown in bold are millimetres.
Other dimensions are in inches.
Minimum Pressure required 5.1 BAR / 75 lbf/in25.4 BAR / 80 lbf/in26.1 BAR / 90 lbf/in2
0734
3.5
89
2.7
68
6.14
156
2.5
63.5
1.90
48
12.5
317
12.5°
76
2.99 104
4.1
23
.90
B
A
31.7Ø
1.25Ø
19
.75
63.5
2.5

10
PU T T I N G I N T O S E R V I C E
0734
8
6
4
2
0
10
12
14
16
TAKE OFF POINT
FROM MAIN SUPPLY
STOP COCK
(USED DURING MAINTENANCE
OF FILTER/REGULATOR
OR LUBRICATION UNITS)
MAIN SUPPLY
DRAIN POINT
PRESSURE REGULATOR
AND FILTER
(DRAIN DAILY)
LUBRICATOR
3
M
E
T
R
E
S
M
A
X
I
M
U
M
A I R S U P P L Y
All tools are operated with compressed air at an optimum pressure of 5.5 bar. We recommend the use of pressure regulators and
automaticoiling/filtering systems onthemain air supply.Theseshould be fitted within3metres of thetool(see diagram below)to ensure
maximum tool life and minimum tool maintenance.
Air supply hoses should have a minimum working effective pressure rating of 150% of the maximum pressure produced in the system
or 10 bar, whichever is the highest. Air hoses should be oil resistant, have an abrasion resistant exterior and should be armoured where
operating conditions may result in hoses being damaged. All air hoses MUST have a minimum bore diameter of 6.4 millimetres or1/4inch.
Read servicing daily details page 17.
O P E R A T I N G P R O C E D U R E
OPTION 1
Ensure that the correct nose equipment is fitted.
Connect the tool to the air supply.
Insert the fastener body squarely into the prepared hole of the
application.
Apply the tool to the protruding rivet stem.
Fully depress the trigger. The tool cycle will ensure the rivet is
placed.
OPTION 2
Ensure that the correct nose equipment is fitted.
Connect the tool to the air supply.
Insert the fastener stem into the nose of the tool.
Insert the tool with the fastener squarely into the prepared
hole of the application.
Fully depress the trigger. The tool cycle will ensure the rivet is
placed.
■
■
■
■
■
■
■
■
■
■

Hose Connector
part nº 07005-00276 Hose Assembly part nº 07008-000324
Swivel Connector assembly
part nº 07640-01400
11
Three different accessories are available to make the connection to your air supply:
A C C E S S O R I E S
1/4” BSP
TO FIT 6.4 mm (1/4”) BORE PIPE
L = 137 cm
Approximate dimensions of assembled unit are:
Length: 107mm (4.2”)
Diameter: 63.5mm (2.5”)
The stem catcher MUST be emptied frequently. (approx. half full or every 120 placings)
CLAMP WASHER
STEM CATCHER
BODY
‘O’ RING
END COVER
LOCKING RING
Part number: 07340-08800
STEM CATCHER
ADAPTOR
STEM CATCHER
OUTER
1/4” BSP
1/4” BSP
You may want to consider one more accessory to improve efficiency. FOR USE ON 07340 & 07344 TOOLS ONLY.
STEM CATCHER UNIT
To replace the pin tail deflector with
the stem catcher unit, unscrew the end
cap and remove together with pintail
deflector (items 56 and 55 of page
22).
Assemble all items in the order shown
on the diagram opposite.
Offer the assembly to the new stem
catcher adaptor.
Start tightening the locking ring onto
stem catcher adaptor.
Rotate the stem catcher body until the
opening is in the desired position.
Fully tighten the locking ring.
■
■
■
■
■
■

There are three types of nose assemblies used with the 0734 type of tooling, these combine with three types of base tools to make up
the six models: 07340, 07344, 07345, 07346, 07347 and 07348. If you have purchased a complete tool, it will already be fitted
with the correct nose assembly for your fastener.
It is essential that the correct nose assembly is fitted prior to operating the tool. By knowing your original complete tool part number
or the details of the fastener to be placed, you will be able to order a new complete nose assembly using the selection table pages 4,
5, 6, 7, 8 and 9 according to the tool model you are using.
0 7 3 4 0 / 4 / 7 / 8 M O D E L S
While these models all use fixed nose assemblies, there will be minor variations on some components. Check part numbers on respective
component table.
12
NO S E A S S E M B L I E S
5 6 7 8
1 2 3 4
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
SERVICING INSTRUCTIONS
Nose assemblies should be serviced at weekly intervals.
Remove the complete nose assembly using the reverse procedure to the ‘Fitting Instructions’.
Any worn or damaged part should be replaced by a new part.
Particularly check wear on jaws.
Ensure jaw spreader assembly tube 5, where fitted, is not distorted.
Check spring 7 is not distorted.
Assemble according to fitting instructions.
Lightly coat the jaws with Moly lithium grease.
Drop jaws 4 into jaw housing 3.
Insert jaw spreader 5 into jaw housing 3 (locating in the ‘V’ shape formed by the jaws).
Locate buffer 6 on jaw spreader 5.
Locate spring 7 onto jaw spreader 5.
Fit locking ring 8 onto the jaw spreader housing assembly of the tool.
Holdingtool pointing down, screwonthe assembled jawhousingonto the jawspreaderhousing assembly andtightenwith spanner.
Screw nose tip 1 into nose casing 2.
Place nose casing 2 over jaw housing 3, tightening with spanner.
FITTING INSTRUCTIONS
I M P O R T A N T
The air supply must be disconnected when fitting or removing nose assemblies unless specifically instructed otherwise.

13
07340/4/7/8 NOSE ASSEMBLY COMPONENTS
Each nose assembly represents a unique combination of components which can be ordered individually. Component numbers refer to
the illustration on the opposite page. We recommend some stock as items will need regular replacement. Read the Nose Assemblies
servicing instructions opposite carefully.
NOSE ASSY 1 2 3 45678
07241-07300 07241-07101 07340-02804 07340-00304 07340-00213 07240-01501 07340-01503 07340-01502 07340-00327
07340-07300 07340-07301 07340-02804 07340-00304 07340-07502 07340-07503 07340-01503 07340-01502 07340-00327
07340-07600 07340-07601 07340-00306 07340-00304 07340-00213 07344-01400 07340-01304 07340-01303 07340-00327
07381-04600 07381-04601 07340-00306 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07381-04700 07381-04701 07340-00306 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07490-00900 07340-06000 07340-00306 07340-00304 07340-00213 07340-01300 07340-01304 07340-01303 07340-00327
07490-01000 07340-02805 07340-02804 07340-00304 07340-00213 07340-01300 07340-01304 07340-01303 07340-00327
07490-01400 07340-06300 07340-00306 07340-00304 07340-00222 07340-02000 07340-01304 07340-01303 07340-00327
07490-01600 07340-06100 07340-00306 07340-00304 07340-00213 07340-05700 07340-01304 07340-01303 07340-00327
07490-01700 07340-02806 07340-02804 07340-00304 07340-00213 07344-05700 07340-01304 07340-01303 07340-00327
07490-02300 07340-06200 07340-00306 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07490-02400 07340-02807 07340-02804 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07490-04100 07340-06400 07340-00306 07340-00304 07340-00213 07340-01300 07340-01304 07340-01303 07340-00327
07490-04200 07340-06500 07340-00306 07340-00304 07340-00213 07344-01300 07340-01304 07340-01303 07340-00327
07490-04300 07340-06600 07340-00306 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07490-04900 07340-04400 07340-00306 07340-00304 07340-07502 07340-07503 07340-01503 07340-01502 07340-00327
07490-05000 07340-04800 07340-00306 07304-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07498-08400 07498-08401 07340-00306 07340-00304 07340-00213 07340-03702 07498-01304 07340-01303 07340-00327
07498-09100 07498-09101 07340-00306 07340-00304 07490-04602 07498-03002 07498-03003 07100-04003 07340-00327
07640-02100 07340-07701 07340-00306 07340-00304 07100-08203 07241-03702 07241-02001 07498-04301 07340-00327
07640-02200 07340-07801 07340-00306 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07640-02400 07340-07901 07340-00306 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07640-03100 07498-08501 07340-00306 07340-00304 07100-08203 07241-03702 07241-02001 07498-04301 07340-00327
07640-03200 07498-08601 07340-00306 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07640-03400 07498-08701 07340-00306 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07640-08300 07340-08301 07340-00306 07340-00304 07340-04602 07498-03002 07498-03003 07100-04003 07340-00327
07340
NOSE ASSY 1 2 3 45678
07344-02100 07344-02101 07344-02001 07340-00304 07340-00213 07344-01400 07340-01304 07340-01303 07340-00327
07344-02300 07140-02104 07344-02001 07340-00304 07340-00229 07344-01400 07340-01304 07340-01303 07340-00327
07344-02400 07344-02401 07344-02001 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07344-02600 07140-02105 07344-02001 07340-00304 07340-00229 07344-02002 07340-01503 07340-01502 07340-00327
07344-02700 07140-02106 07344-02001 07340-00304 07340-00229 07344-02002 07340-01503 07340-01502 07340-00327
07344-02900 07344-02901 07344-02001 07340-00304 07340-00229 07344-02002 07340-01503 07340-01502 07340-00327
07344-03000 07344-03001 07344-02001 07340-00304 07340-00229 07344-02002 07340-01503 07340-01502 07340-00327
07344-03100 07344-03101 07344-02001 07340-00304 07498-04401 07344-02002 07340-01503 07340-01502 07340-00327
07344-03200 07344-07101 07344-02001 07340-00304 07340-00229 07344-02002 00000- 07498-06801 07340-00327
07344-04700 07344-04701 07498-02601 07498-04503 07498-04501 07498-04800 07498-03003 07100-04003 07340-00327
07344-05100 07344-04701 07498-02601 07340-00304 07340-00229 07498-03002 - 07100-04003 07340-00327
07344-05300 07344-04701 07498-02601 07498-04503 07498-04501 07498-04502 - 07100-04003 07340-00327
07498-02400 07340-06701 07344-02001 07340-00304 07498-04401 07340-01300 07340-01304 07340-01303 07340-00327
07498-02500 07340-06801 07344-02001 07498-04503 07498-04501 07498-04800 07498-03003 07100-04003 07340-00327
07498-06700 07340-06701 07344-02001 07340-00304 07340-00229 07340-01400 07340-01304 07340-01303 07340-00327
07498-06800 07340--06801 07344-02001 07340-00304 07340-00229 07344-02002 - 07498-06801 07340-00327
07498-06900 07340-06901 07344-02001 07304-00304 07340-00229 07340-02002 00000- 07498-06801 07340-00327
07498-07000 07340-07001 07344-02001 07340-00304 07340-00229 07344-02002 - 07498-06801 07340-00327
07344

14
NOSE ASSY 1 2 3 45678
07347-03000 07340-06001 07340-00306 07340-00304 07340-00213 07340-01300 07340-01304 07340-01301 07340-00327
07347-03100 07340-06301 07340-00306 07340-00304 07340-00222 07340-02000 07340-01304 07340-01301 07340-00327
07347-03200 07340-06101 07340-00306 07340-00304 07340-00213 07340-05700 07340-01304 07340-01303 07340-00327
07347-03300 07381-04701 07340-00306 07340-00304 07340-00213 07347-03301 07498-03003 07100-04003 07340-00327
07347-03400 07340-06401 07340-00306 07340-00304 07340-00213 07340-01300 07340-01304 07340-01303 07340-00327
07347-03500 07340-06501 07340-00306 07340-00304 07340-00213 07340-05700 07340-01304 07340-01303 07340-00327
07347-03600 07340-06601 07340-00306 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07344-02300 07140-02104 07344-02001 07340-00304 07340-00229 07344-01400 07340-01304 07340-01303 07340-00327
07344-02400 07344-02401 07344-02001 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07344-02600 07140-02105 07344-02001 07340-00304 07340-00229 07344-02002 07340-01503 07340-01502 07340-00327
07344-02700 07140-02106 07344-02001 07340-00304 07340-00229 07344-02002 07340-01503 07100-01502 07340-00327
07344-02900 07344-02901 07344-02001 07340-00304 07340-00229 07344-02002 07340-01503 07340-01502 07340-00327
07344-03000 07344-03001 07344-02001 07340-00304 07340-00229 07344-02002 07340-01503 07340-01502 07340-00327
07344-03100 07344-03101 07344-02001 07340-00304 07498-04401 07344-02002 07340-01503 07340-01502 07340-00327
07640-02100 07340-07701 07340-00306 07340-00304 07100-08203 07241-03702 07241-02001 07498-04301 07340-00327
07640-02200 07340-07701 07340-00306 07340-00304 07100-08203 07241-03702 07241-02001 07498-04301 07340-00327
07640-02400 07340-07901 07340-00306 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07340-07600 07340-07601 07340-00306 07340-00304 07340-00213 07344-01400 07340-01304 07340-01303 07340-00327
07340-08300 07340-08301 07340-00306 07340-00304 07490-04602 07498-03002 07498-03003 07100-04003 07340-00327
07490-01000 07340-02805 07340-02804 07340-00304 07340-00213 07340-01300 07340-01304 07340-01303 07340-00327
07490-01700 07340-02806 07340-02804 07340-00304 07340-00213 07340-05700 07340-01304 07340-01303 07340-00327
07349-02400 07340-02807 07340-02807 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07490-05000 07340-04800 07340-00306 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07498-04500 07498-03001 07340-00306 07498-04503 07498-04501 07498-04502 07498-03003 07100-04003 07340-00327
07640-03100 07498-08501 07340-00306 07340-00304 07100-08203 07241-03702 07241-02001 07498-04301 07340-00327
07640-03200 07498-08601 07340-00306 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07640-03400 07498-08701 07340-00306 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07498-08400 07498-08401 07340-00306 07340-00304 07340-00213 07340-07502 07340-01304 07340-01303 07340-00327
07498-09100 07498-09101 07340-00306 07340-00304 07498-04602 07498-03002 07498-03003 07100-04003 07340-00327
07498-01600 07605-00220 07340-00306 07498-04503 07498-04501 07498-04502 07498-03003 07100-04003 07340-00327
07498-06700 07340-06701 07344-02001 07340-00304 07340-00229 07344-01400 07340-01304 07340-01303 07340-00327
07498-06800 07340-06801 07344-02001 07340-00304 07340-00229 07344-02002 - 07498-06801 07340-00327
07498-06900 07340-06901 07344-02001 07340-00304 07340-00229 07344-02002 - 07498-06801 07340-00327
07498-07000 07340-07001 07344-02001 07340-00304 07340-00229 07344-02002 07340- 07498-06801 07340-00327
07498-02400 07340-06701 07344-02001 07340-00304 07498-04401 07340-01300 07340-01304 07340-01303 07340-00327
07498-02500 07340-06801 07344-02001 07498-04503 07498-04501 07498-04800 07498-03003 07100-04003 07340-00327
07241-07300 07241-07101 07340-02804 07340-00304 07340-00213 07340-01501 07340-01503 07340-01502 07340-00327
07241-07400 07340-06201 07340-00306 07340-00304 07340-00213 07347-03301 07498-03003 07100-04003 07340-00327
07381-04800 07490-04401 07340-00306 07340-00304 07340-07502 07381-04801 07340-01503 07100-04003 07340-00327
07347
NOSE ASSY 1 2 3 45678
07348-00800 07340-06000 07348-00801 07340-00304 07340-00213 07241-03002 07241-02001 07500-00418 07340-00327
07348-01400 07340-06300 07348-00801 07340-00304 07340-00222 07241-03002 07241-02001 07500-00418 07340-00327
07348-01600 07340-06100 07348-00801 07340-00304 07340-00213 07241-03002 07241-02001 07498-04301 07340-00327
07348-02100 07340-07701 07348-00801 07340-00304 07100-08203 07241-03702 07241-02001 07498-04301 07340-00327
07348-02200 07340-07801 07348-00801 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07348-02300 07340-06200 07348-00801 07340-00304 07340-00213 07241-03002 07241-02001 07500-00418 07340-00327
07348-02500 07605-00220 07348-00801 07498-04503 07498-04501 07498-04502 07498-03003 07100-04003 07340-00327
07348-02600 07340-07901 07348-00801 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07348-03100 07498-08501 07348-00801 07340-00304 07100-08203 07241-03702 07241-02001 07498-04301 07340-00327
07348-03200 07498-08601 07348-00801 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07348-03400 07498-08701 07348-00801 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07348-04100 07340-06400 07348-00801 07340-00304 07340-00213 07241-03002 07241-02001 07500-00418 07340-00327
07348-04200 07340-06500 07348-00801 07340-00304 07340-00213 07241-03002 07241-02001 07500-00418 07340-00327
07348-04300 07340-06600 07348-00801 07340-00304 07340-00213 07241-03002 07241-02001 07500-00418 07340-00327
07348-04500 07498-03001 07348-00801 07498-04503 07498-04501 07498-04502 07498-03003 07100-04003 07340-00327
07348-04800 07344-02101 07348-05101 07340-00304 07340-00213 07241-02202 07241-02001 07498-04301 07340-00327
07348-04900 07490-04400 07348-00801 07340-00304 07340-07502 07241-03702 07241-02001 07498-04301 07340-00327
07348-05000 07340-04800 07348-00801 07340-00304 07340-00213 07241-03002 07241-02001 07500-00418 07340-00327
07348-05100 07140-02104 07348-05101 07340-00304 07340-00229 07241-02202 07241-02001 07498-04301 07340-00327
07348-05200 07140-02105 07348-05101 07304-00304 07340-00229 07241-02202 07241-02001 07498-04301 07340-00327
07348-05300 07140-02106 07348-05101 07304-00304 07340-00229 07241-02202 07241-02001 07498-04301 07340-00327
07348-05400 07344-02901 07348-05101 07340-00304 07340-00229 07241-02202 07241-02001 07498-04301 07340-00327
07348-05500 07344-03001 07348-05101 07340-00304 07340-00229 07241-02202 07241-02001 07498-04301 07340-00327
07348-05600 07344-03101 07348-05101 07340-00304 07340-00229 07241-02202 07241-02001 07498-04301 07340-00327
07348-05700 07344-02401 07348-05101 07340-00304 07340-00229 07241-02202 07241-02001 07498-04301 07340-00327
07348-05800 07340-06701 07348-05101 07340-00304 07340-00229 07241-02202 07241-02001 07498-04301 07340-00327
07348-05900 07340-06801 07348-05101 07340-00304 07340-00229 07241-02202 07241- 07498-04301 07340-00327
07348-06000 07340-06901 07348-05101 07340-00304 07340-00229 07241-02202 07241- 07498-04301 07340-00327
07348-06100 07340-07001 07348-05101 07340-00304 07340-00229 07241-02202 07241- 07498-04301 07340-00327
07348-06200 07340-07101 07348-05101 07340-00304 07340-00229 07241-02202 07241- 07498-04301 07340-00327
07348-06300 07340-06701 07348-05101 07498-04503 07498-04501 07498-04802 07241-02001 07100-04003 07340-00327
07348-06400 07340-06801 07348-05101 07498-04503 07498-04501 07498-04802 07241-02001 07100-04003 07340-00327
07348-06800 07348-06801 07348-00801 07340-00304 07340-00213 07241-03002 07241-02001 07500-00418 07340-00327
07348-08300 07340-08301 07348-00801 07340-00304 07490-04602 07498-03002 07498-03003 07100-04003 07340-00327
07348-09100 07340-09101 07348-00801 07340-00304 07490-04602 07498-03002 07498-03003 07100-04003 07340-00327
07348

15
STRAIGHT SWIVEL NOSE ASSEMBLY RIGHT-ANGLE SWIVEL NOSE ASSEMBLY
2
1
15
9
8
8
10
7
11
17 18 19 20
316
16
4
12
14
13
6
6
5
16
1
3
12
14
13
16
6
5
21
22 11 7
9
8
8
8
10
17 18
19 20
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
0 7 3 4 5 & 0 7 3 4 6 M O D E L S
As described on pages 6 and 7 the fitting of a straight swivel nose assembly to a 07340-00200 base tool will create a 07345 tool model
and the fitting of a right-angle swivel nose assembly to the same base tool will create a 07346 tool model. Because there are few
differences between the two nose assemblies, the fitting and servicing procedures are almost identical.
FITTING INSTRUCTIONS
The following procedure will allow you to fit either of the swivel nose assemblies ( as illustrated below ) to the tool. If you order a complete
nose assembly rather than individual components, you will only need to start at stage ■.
Allmovingpartsshould be lubricated. Unless stated otherwise use Moly lithiumgrease( detailspage17 ).Whenongrey tint, instructions
refer only to the right-angle nose assembly fitted to 07346 models.
Fit locking ring 10, detailed below, over jaw spreader housing of tool (item 47 page 22).
Coat screw 13 with thread locking adhesive and use to secure nose tip 14 onto body 5.
Lightly lubricate items 17,18,19,20 and insert into jaw carrier 3 as shown. Secure with screws 16.
Position lever 4 into body 5 and hold in place with pin 15 through the hole of body 5 (not a slot).
Lubricate the sides of the jaw carrier assembly and insert into body 5.
Lubricate rollers 8 and ENSURE that they will freely rotate in the holes of adaptor 9. If necessary ream the holes.
Position spring clip 7 over adaptor 9 past the holes for the rollers and rotate until the locating peg is aligned with the corresponding
hole in adaptor 9 (smallest hole).
Fit adaptor 9 over the end of body 5 and drop rollers 8 into place. Push spring clip 7 over rollers 8.
Insert spindle 11 through adaptor 9 into jaw carrier 3 until the hole lines up with slot in body 5. Temporarily hold in place with pin 6.
Insert pin 12 through the front slot of body 5 into jaw carrier 3.
Hold the assembly vertical to prevent all pins dropping and slide the jaw carrier assembly back and forth a few times to ensure
free movement.
Push pin(s) 6 out and let spindle 11 drop out. Screw spindle 11 onto the jaw spreader housing of the tool, leaving the small screw
fixing hole uppermost for straight swivel nose assemblies. Tighten gently with a tommy bar.
Screw the assembly over spindle 11 onto the tool handle. Replace pin(s) 6.
On straight swivel nose assemblies attach platform 22 onto the top of the spindle with screw 21. Deburr the back end of platform
22 so that it cannot catch on guard 1.
Snap guard 1 over the assembly, carefully sliding cut-out around the head of screw 15 and secure with screw 2.

16
17 18
19 20
SERVICING INSTRUCTIONS
Nose assemblies should be serviced at weekly intervals.
Item numbers refer to both illustrations on page 15.
Remove the complete nose assembly using the reverse proce-
dure to the ‘Fitting instructions’.
If guard 1 is at all damaged it must be replaced by a new one.
Any worn or damaged parts should be replaced.
Pay particular attention to jaw carrier items in the upper
illustration on the right as follows:
Check wear on jaws 17.
Check that jaw spreader tube 18 is not distorted.
Check that spring 19 is neither broken or distorted.
Check that spring guide 20 is not damaged.
Check that spring clip 7 is not distorted. When removing
spring clip 7, use two screwdrivers as shown in the lower
illustration opposite.
Check for excessive wear on slots of body 5.
Assemble according to fitting instructions.
■
■
■
■
■
■
■
NOSE ASSY NOSE TIP(14) JAWS(17) NOSE ASSY NOSE TIP(14) JAWS(17)
07345-03000 07345-03600 07340-00213
07345-03100 07345-03700 07340-00213
07345-03200 07345-03800 07490-04602
07345-03300 07345-03301 07340-00229
07345-03400 07345-03401 07340-00229
07345-03500 07345-03501 07498-04401
07345-04000 07165-00701 07340-00229
07345-04100 07165-00702 07340-00229
07345-04200 07165-00703 07498-04401
07345-04300 07165-00801 07340-00229
07345-04400 07165-00802 07498-04401
07346-03000 07345-03600 07340-00213
07346-03100 07345-03700 07340-00213
07346-03200 07345-03800 07490-04602
07346-03300 07345-03301 07340-00229
07346-03400 07345-03401 07340-00229
07346-03500 07345-03501 07498-04401
07346-04000 07165-00701 07340-00229
07346-04100 07165-00702 07340-00229
07346-04200 07165-00703 07498-04401
07346-04300 07165-00801 07340-00229
07346-04400 07165-00802 07498-04401
07494-03000 07494-03011 07340-00213
07494-03400 07494-03401 07340-00222
07494-03600 07494-03601 07340-00229
07494-03700 07494-03701 07340-00229
07494-03800 07494-03801 07498-04401
07494-06000 07494-06001 07340-00213
07494-06100 07494-06101 07340-00213
07494-06600 07494-06601 07340-00213
07494-06700 07494-06701 07340-00213
07495-03000 07494-03011 07340-00213
07495-03400 07494-03401 07340-00222
07495-03600 07494-03601 07340-00229
07495-03700 07494-03701 07340-00229
07495-03800 07494-03801 07498-04401
07495-04000 07494-06001 07340-00213
07495-04100 07494-06101 07340-00213
07495-04700 07494-06601 07340-00213
07495-04800 07494-06701 07340-00213
VARYING COMPONENTS
ITEM 07345 07346
1
2
3
4
5
6
7
8
9
10
11
12
13
15
16
18
19
20
21
22
GUARD
BLADE SCREW
JAW CARRIER
LEVER
BODY
PIVOT PIN
SPRING CLIP
ROLLER
ADAPTOR
LOCKING RING
SPINDLE
DOWEL PIN
SCREW
PIVOT PIN
SCREW
JAW SPREADER
SPRING
SPRING GUIDE
CSK. SCREW
PLATFORM
07494-05000
-
07494-03026
-
07494-03015
07343-02207
07495-03900
07007-00039
07345-03001
07345-03003
07345-03002
07007-00038
07342-02207
-
07494-03028
07166-01100
07166-01102
07494-03027
07001-00368
07345-00401
07495-03003
07210-02015
07494-03026
07495-03004
07495-03002
07343-02207
07495-03900
07007-00039
07345-03001
07345-03003
07345-03002
07007-00038
07342-02207
07495-03005
07494-03028
07166-01100
07166-01102
07494-03027
-
-
CONSTANT COMPONENTS
07345 & 07346 NOSE ASSEMBLY COMPONENTS
Nose tips and jaws will vary for each nose assembly while other components remain the same as shown in the tables below. Jaws are
always in pairs.

17
Regular servicing should be carried out and a comprehensive inspection performed annually or every 500,000 cycles, whichever is
sooner.
I M P O R T A N T
The employer is responsible for ensuring that tool maintenance instructions are given to the appropriate personnel.
The operator should not be involved in maintenance or repair of the tool unless properly trained.
D A I L Y
Daily, before use or when first putting the tool into service, pour a few drops of clean, light lubricating oil into the air inlet of the
tool if no lubricator is fitted on air supply. If the tool is in continuous use, the air hose should be disconnected from the main air
supply and the tool lubricated every two to three hours.
Check for air leaks. If damaged, hoses and couplings should be replaced by new items.
If there is no filter on the pressure regulator, bleed the air line to clear it of accumulated dirt or water before connecting the air
hose to the tool. If there is a filter, drain it.
Check that the nose equipment is correct.
Check the stroke of the tool meets the minimum specification (inside front page). It is the difference in the measurement between
the front face of the jaw spreader housing assembly and the front face off the handle top bore before pressing the trigger and
when it is fully depressed.
W E E K L Y
Dismantle and clean the nose assembly with special attention to the jaws. Lubricate with Moly Lithium grease before assembling.
Check for oil leaks and air leaks in the air supply hose and fittings.
Grease can be ordered as a single item, the part number is shown in the service kit page 18.
■
■
■
■
■
SE R V I C I N G T H E T O O L
■
■
M O L Y L I T H I U M G R E A S E E P 3 7 5 3 S A F E T Y D A T A
FIRE
FLASH POINT: Above 220°C.
Not classified as flammable.
Suitable extinguishing media: CO2, Halon or water spray
if applied by an experienced operator.
HANDLING
Use barrier cream or oil resistant gloves
STORAGE
Away from heat and oxidising agent.
FIRST AID
SKIN: As the grease is completely water resistant it is best
removed with an approved emulsifying skin cleaner.
INGESTION: Make the individual drink 30ml Milk of
Magnesia, preferably in a cup of milk.
EYES: Irritant but not harmful. Irrigate with water and
seek medical attention.
ENVIRONMENT
Scrape up for burning or disposal on approved site.

18
For all servicing we recommend the use of the service kit below (part number 07900-03400) supplied in its own plastic case.The kit
for the 07348 has a different part number 07900-03480 because it contains a different spring compression tool part number 07900-
00170.
ITEM PART Nº DESCRIPTION Nº OFF
SERVICE KIT
07900-00001 SPRING COMPRESSION TOOL 1
07900-00002 SPANNER ASSEMBLY FOR HEAD PISTON 1
07900-00004 CIRCLIP PLIERS 1
07900-00005 PLUG 1
07900-00006 'O' RING ASSEMBLING TOOL 1
07900-00008
7
/ 16 " x
1
/ 2 " A/F SPANNER 1
07900-00009
3
/ 32 " A/F SPANNER 1
07900-00010 PIN PUNCH 1
07900-00012
9
/ 16 " x
5
/ 8 " A/F SPANNER 1
07900-00013
1
/ 8 " ALLEN KEY 1
07900-00015
5
/ 8 " x
11
/ 16 " A/F SPANNER 1
07900-00018 PISTON EXTRACTOR 1
07900-00427 SLIDING OFFSET HANDLE 1
ITEM PART Nº DESCRIPTION Nº OFF
SERVICE KIT (Continued)
07900-00087 SOCKET ASSEMBLY (ADAPTOR) 1
07900-00092
3
/ 4 " x
7
/ 8 " A/F SPANNER 1
07992-00020 80g TIN MOLY LITHIUM GREASE EP 3753 1
07900-00151 'T' HANDLE. EXTENSION 1
07900-00192 PRIMING PUMP ASSEMBLY 1
07900-00078
5
/ 32 " A/F ALLEN KEY 1
07900-00203 TORQUE WRENCH 1
07900-00401 ADAPTOR 1
07340-00306 NOSE CASING 1
07900-00421
13
/ 16 " A/F RING SPANNER 1
07900-00422
3
/ 4 " A/F RING SPANNER 1
07900-00638 PRIMING SPACER 1