Avdel 74100 User manual

74100 & 74101 Threaded Insert Power Tool
Nose Assembly Fitting Instructions
IMPORTANT
The air supply must be disconnected when fitting or removing nose assemblies unless specifically instructed otherwise.
Note: Before fitting the nose equipment, ensure the clutch on the tool is set to the correct torque for the insert being placed. It is also
essential that the correct Nose Assembly is fitted prior to operating the tool. Torque Values and complete Nose Assembly part
numbers can be found in the 74100 & 74101 Instruction Manual sections Tool Selection and Nose Assemblies respectively.
Item numbers in bold refer to illustration below:
•Where applicable, insert Sleeve 8and Thrust Spring 9into Nose Housing 2.
•Coat Thrust Washers 3and Thrust Bearing 4with high pressure grease (eg. Shell Alvania E.P.I.) and locate them in the order shown below
into the Nose Housing 2.
•Where applicable, fit Spacer 5through Thrust Washers and Thrust Bearing.
•Insert Drive Screw 1through the above assembly.
•Fit Drive Shaft 6into the hexagonal hole in the Drive Screw head.
•Insert Stop 11 and Spring 10 into the front of the Base Tool.
•Screw Adaptor 7into Clutch Housing of the Base Tool (left hand thread).
•Offer up the Nose Assembly to the Adaptor. It will be necessary to rotate the Drive Screw by hand to locate the hexagon on the Drive Shaft
with the hexagonal hole in the front jaw of the Base Tool.
•Screw the Nose Housing onto the Adaptor and tighten with a suitable spanner (left hand thread).
Nose assemblies should be serviced at weekly intervals.
•Remove complete Nose Assembly using the reverse procedure to the ‘Fitting Instructions’.
•Any worn or damaged part should be replaced.
•Particularly check wear on Drive Screw, Thrust Washers and Thrust Bearing.
•Lubricate Thrust Washers and Thrust Bearing with high pressure grease (eg Shell Alvania E.P.I.).
•Check Springs are not distorted. Replace if necessary.
•Reassemble according to fitting instructions.
289
1610
34 3 5
11 7
Servicing Instructions
Fitting Instructions

289
1610
34 3 5
11 7
1
74110 Threaded Insert Power Tool
Nose Assembly Fitting Instructions
IMPORTANT
The air supply must be disconnected when fitting or removing nose assemblies unless specifically instructed otherwise.
Note: Before fitting the nose equipment, ensure the clutch on the tool is set to the correct torque for the insert being placed. It is also
essential that the correct Nose Assembly is fitted prior to operating the tool. Torque Values and complete Nose Assembly part
numbers can be found in the 74110 Instruction Manual sections Tool Selection and Nose Assemblies respectively.
Item numbers in bold refer to illustration below:
•Where applicable, insert Sleeve 8and Thrust Spring 9into Nose Housing 2.
•Coat Thrust Washers 3and Thrust Bearing 4with high pressure grease (eg. Shell Alvania E.P.I.) and locate them in the order shown below
into the Nose Housing 2.
•Where applicable, fit Spacer 5through Thrust Washers and Thrust Bearing.
•Insert Drive Screw 1through the above assembly.
•Fit Drive Shaft 6into the hexagonal hole in the Drive Screw head.
•Insert Stop 11 and Spring 10 into the front of the Base Tool.
•Screw Adaptor 7into Clutch Housing of the Base Tool (left hand thread).
•Offer up the Nose Assembly to the Adaptor. It will be necessary to rotate the Drive Screw by hand to locate the hexagon on the Drive Shaft
with the hexagonal hole in the front jaw of the Base Tool.
•Screw the Nose Housing onto the Adaptor and tighten with a suitable spanner (left hand thread).
Nose assemblies should be serviced at weekly intervals.
•Remove complete Nose Assembly using the reverse procedure to the ‘Fitting Instructions’.
•Any worn or damaged part should be replaced.
•Particularly check wear on Drive Screw, Thrust Washers and Thrust Bearing.
•Lubricate Thrust Washers and Thrust Bearing with high pressure grease (eg Shell Alvania E.P.I.).
•Check Springs are not distorted. Replace if necessary.
•Reassemble according to fitting instructions.
Fitting Instructions
Servicing Instructions

Notes

Since 1 936 2010Since 1922
www.avdel-global.com
www.infastech.com
02.2011 • © 2010 Infastech
Autosert®(equipment), Avbolt ®, Avdel®, Avdelmate®, Avdel TX2000®, Avdelok®, Avex®, Avibulb®, Avinox®, Avinut™, Avlug
®, Avmatic®, Avplas®,
Avseal®, Avsert®, Avtainer®, Avtronic®, Briv®, Bulbex®, Chobert®, Eurosert®, Fastriv®, Finsert®, Genesis®, Grovit®, Hemlok®, Hexsert®, Holding
your world together®, Hydra®, Interlock®, Klamp-Tite ®, Klamptite KTR ®, Kvex®, Maxlok®, Monobolt®, Monobulb®, Neobolt®, Nutsert®, Nutsert
SQ®, Portariv®, Rivmatic®, Rivscrew®, Speed Fastening®, Squaresert®, Stavex®, Supersert®, Thin Sheet Nutsert®, Titan®, T-Lok®, TLR®, TSN
®,
TX2000®, Versa-Nut®, Viking®and Viking360 ®are trademarks of Avdel UK Limited. Infastech™ and Our Technology, Your Success™ are
trademarks of Infastech Intellectual Properties Pte Ltd. The names and logos of other companies mentioned herein may be trademarks
of their respective owners. This document is for informational purposes only. Infastech makes no warranties, expressed or implied, in this
document. Data shown is subject to change without prior notice as a result of continuous product development and improvement policy.
Your local Avdel representative is at your disposal should you need to confirm latest information.
AUSTRALIA
Infastech (Australia) Pty Ltd.
891 Wellington Road
Rowville
Victoria 3178
Tel: [phone]
Fax: [phone]
[e-mail]
CANADA
Avdel Canada Limited
1030 Lorimar Drive
Mississauga
Ontario L5S 1R8
Tel: [phone]
Fax: [phone]
infoA[email protected]
CHINA
Infastech (China) Ltd.
RM1708, 17/F., NanyangPlaza,
57 HungTo Rd., Kwun Tong
HongKong
Tel: [phone]
Fax: [phone]
[e-mail]
FRANCE
Avdel France S.A.S.
33 bis, rue des Ardennes
BP4
75921 Paris Cedex 19
Tel: [phone]
Fax: [phone]
AvdelF[email protected]
GERMANY
Avdel Deutschland GmbH
Klusriede 24
30851 Langenhagen
Tel: [phone]
Fax: [phone]
[e-mail]
INDIA
Infastech Fastening Technologies
India Private Limited
Plot No OZ-14, Hi Tech SEZ,
SIPCOT Industrial Growth Center,
Oragadam, Sriperumbudur Taluk,
Kanchipuram District,
602105 Tamilnadu
Tel: [phone]
Fax: [phone]
[e-mail]
ITALY
Avdel Italia S.r.l.
Viale Lombardia 51/53
20047 Brugherio (MI)
Tel: [phone]
Fax: [phone]
[e-mail]
JAPAN
Infastech Kabushiki Kaisha
Center Minami SKY,
3-1 Chigasaki-Chuo, Tsuzuki-ku,
Yokohama-city,
Kanagawa Prefecture
Japan 224-0032
Tel: [phone]
Fax: [phone]
[e-mail]
MALAYSIA
Infastech (Malaysia) Sdn Bhd
Lot 63, Persiaran Bunga Tanjung1,
SenawangIndustrial Park
70400 Seremban
Negeri Sembilan
Tel:
[phone]
Fax: [phone]
info-m[email protected]
SINGAPORE
Infastech (Singapore) Pte Ltd.
31 Kaki Bukit Road 3
#05-03/06 Techlink
Singapore, 417818
Tel: [phone]
Fax: [phone]
[e-mail]
SOUTH KOREA
Infastech (Korea) Ltd.
212-4, Suyang-Ri,
Silchon-Eup, Kwangju-City,
Kyunggi-Do, Korea, 464-874
Tel: [phone]
Fax: [phone]
[e-mail]
SPAIN
Avdel Spain S.A.
C/ Puerto de la Morcuera, 14
Poligono Industrial Prado Overa
Ctra. de Toledo, km 7,8
28919 Leganés (Madrid)
Tel: [phone]
Fax: [phone]
[e-mail]
TAIWAN
Infastech/Tri-Star Limited
No 269-7, BaodongRd,
Guanmiao Township,
71841 Tainan County,
Taiwan, R.O.C
Tel:
[phone] (ext 201)
Fax: [phone]
[e-mail]
UNITED KINGDOM
Avdel UK Limited
Pacific House
2 Swiftfields
Watchmead Industrial Estate
Welwyn Garden City
Hertfordshire AL7 1LY
Tel: [phone]
Fax: [phone]
[email protected]
USA
Avdel USA LLC
614 NC Highway 200 South
Stanfield, North Carolina 28163
Tel: [phone]
Fax: [phone]
infoA[email protected]
Manual No. Issue Change Note No.
A 07/176
A2 11/072
07900-00812