AXIOMTEK eBOX627-312-FL-N3350-DC User manual

eBOX627-312-FL
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, or any liability arising from such uses.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update any information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in
any forms or by any means, electronic, mechanical, photocopying, recording, among others,
without prior written permissions of Axiomtek Co., Ltd.
Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
April 2019, Version A2
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The eBOX627-312-FL does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the eBOX627-312-FL before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the eBOX627-312-FL is properly grounded.
4. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen.
6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -40℃or above 80℃. It may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static electricity
on your body.
When handling boards and components, wear a wrist-grounding strap, available from
most electronic component stores.
8. Note!! Caution with touch! eBOX627-312-FL will be hot when it's on.

iv
Classification
1. Degree of production against electric shock : not classified
2. Degree of protection against the ingress of water : IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air
or with oxygen or nitrous oxide.
4. Mode of operation : Continuous

v
General Cleaning Tips
You may need the following precautions before you begin to clean the computer. When you
clean any single part or component for the computer, please read and understand the details
below fully.
When you need to clean the device, please rub it with a piece of dry cloth.
1. Be cautious of the tiny removable components when you use a vacuum cleaner to
absorb the dirt on the floor.
2. Turn the system off before you start to clean up the component or computer.
3. Never drop the components inside the computer or get circuit board damp or wet.
4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of
cleaning. Some individuals may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the computer.
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
your computer and peripherals users can also use household items to clean their computers
and peripherals. Below is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be able to be cleaned using a
product designed for cleaning that component, if this is the case it will be mentioned in the
cleaning.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend you
to rub it with a piece of cloth.
Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or
rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the
plastics parts.
Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of
a computer can be one of the best methods of cleaning a computer. Over time these
items can restrict the airflow in a computer and cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools
for wiping hard to reach areas in your keyboard, mouse, and other locations.
Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs.
NOTE: We strongly recommended that you should shut down the system before you
start to clean any single components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable

vi
Scrap Computer Recycling
If the computer equipment’s needs the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well, please
contact your Axiomtek distributor for recycling and we will make the proper arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, VGA, HDMI are trademarks of International Business Machines Corporation.
Intel®, Pentium®and Celeron®are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBasic are trademarks of Microsoft Corporation.
Windows 10, Windows 8.1, Windows XPE, Windows WinCE embedded, Linux, MS-DOS,
Microsoft C and
Other brand names and trademarks are the properties and registered brands of their
respective owners.

vii
Table of Contents
Disclaimers.............................................................................................................ii
Safety Precautions................................................................................................iii
Classification......................................................................................................... iv
General Cleaning Tips ........................................................................................... v
Scrap Computer Recycling................................................................................... vi
CHAPTER 1 INTRODUCTION .......................................................................1
1.1 General Description...........................................................................1
1.2 System Specifications.......................................................................2
1.2.1 CPU ...................................................................................................................2
1.2.2 I/O System ........................................................................................................2
1.2.3 System Specification.......................................................................................3
1.2.4 Driver CD Content............................................................................................3
1.3 Dimensions ........................................................................................4
1.3.1 System Dimension...........................................................................................4
1.3.2 Wall mount Bracket Dimension......................................................................5
1.3.3Din-rail mount Bracket Dimension.................................................................6
1.3.4VESA mount Bracket Dimension....................................................................7
1.4 I/O Outlets ..........................................................................................8
1.5 Packing List...................................................................................... 10
1.6Model List......................................................................................... 10
CHAPTER 2 HARDWARE INSTALLATION.................................................11
2.1Installing the Memory module......................................................... 11
2.2Installing the PCI Express Mini Card.............................................. 13
2.3Installing the Flexible I/O Window Kit ............................................ 15
2.4Installing the 2.5” SATA Device ...................................................... 18
CHAPTER 3 JUMPER SETTING & CONNECTOR......................................21
3.1 CAPA312 layout................................................................................21
3.2 Jumper Setting Summary................................................................23
3.2.1 Restore BIOS Optimal Defaults (JP3) ..........................................................23
3.2.2 COM3 Data/Power Selection (JP4)...............................................................24
3.2.3AT/ATX Quick Switch (SSW1).......................................................................24
3.3 Connectors.......................................................................................25
3.3.1COM Serial Port Connector (CN22, CN18, CN4 and CN3 )........................26
3.3.2USB 2.0 Port (CN7).........................................................................................26
3.3.3SATA Connector (CN15)................................................................................27
3.3.4HDMI Connector (CN19)................................................................................27
3.3.5USB 3.0 Ports (CN20 and CN21)...................................................................28
3.3.6 Ethernet Ports (LAN1 and LAN2)..................................................................29
3.3.7 Full-size PCI-Express Mini Card Connector (SCN1)...................................30
3.3.8SIM Card Socket (SCN2)................................................................................31
3.3.9 Full-size PCI-Express Mini Card or mSATA Connector (SCN3)................32
3.3.10 Power and HDD LED Indicator .....................................................................33
3.3.11 System Power Switch ...................................................................................33

viii
3.3.12DC-in Phoenix Power Connector .................................................................33
CHAPTER 4 BIOS SETUP UTILITY ............................................................35
4.1 Starting.............................................................................................35
4.2 Navigation Keys............................................................................... 35
4.3 Main Menu........................................................................................ 36
4.4Advanced Menu................................................................................37
4.5 Chipset Menu ...................................................................................52
4.6 Security Menu .................................................................................. 55
4.7 Boot Menu ........................................................................................56
4.8 Save & Exit Menu............................................................................. 57
APPENDIX A WATCHDOG TIMER..............................................................59
About Watchdog Timer ................................................................................... 59
How to Use Watchdog Timer..........................................................................59
APPENDIX B BIOS FLASH UTILITY...........................................................61

eBOX627-312-FL User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the eBOX627-312-FL.
The Chapter 1 includes the following sections:
General Description
System Specification
Dimensions
I/O Outlets
Packing List
Model List
1.1 General Description
The eBOX627-312-FL is an embedded system that supports onboard Intel®Celeron®N3350
Dual-core 2.4 GHz or Pentium®N4200 Quad-core 2.5 GHz SoC onboard with integrated HD
graphics to provide Windows 10 IoT or Linux, suitable for the most endurable operation. It
features fan-less design with full feature I/O, one 204-pin unbuffered SODIMM socket for
singe channel DDR3L-1866 MHz memory, and enhanced system dependability by built-in
Watchdog Timer.
Features
1. Intel®Celeron®N3350 Dual-core SoC, 2.4 GHz by burst enabled or Intel®
Pentium®N4200 Quad-core SoC, 2.5 GHz by burst enabled
2. Maximum to 8GB DDR3L-1866 memory
3. HDMI for display output with lockable connector
4. Supports 4 USB 3.0 & 2 USB 2.0 ports
5. Supports 2 RS-232/422/485 and 2 RS-232
6. Supports dual 10/100/1000Mbps Ethernet ports
7. One 2.5” SATA HDD/SSD drive bay (Maximum 9.5mm height)
8. Two Full-Size Mini PCI Express Mini Card w/mSATA supported
9. Flexible I/O Window
10. One SIM slot
11. Watchdog timer
12. Wide temperature: -20°C~70°C supported (with W.T. SSD & Memory)
13. 9~36VDC phoenix type power input

eBOX627-312-FL User’s Manual
Introduction
2
Reliable and Stable Design
The eBOX627-312-FL adopts the advanced cooling system and supporting wide
operating temperature with fan-less design, which makes it especially suitable in harsh
environments, best for industrial automation, digital signage and gaming application.
Embedded O.S. Supported
The eBOX627-312-FL supports embedded OS, such as Windows 10 IoT 64-bit (UEFI
Mode) and Linux Ubuntu 16.04.3 LTS.
Various Storage devices supported
For storage device, the eBOX627-312-FL supports one 2.5" SATA storage drive bay and
mSATA option supported.
1.2 System Specifications
1.2.1 CPU
CPU
Intel®Celeron®N3350 Dual-core SoC, 2.4GHz by burst enabled or
Intel®Pentium®N4200 Quad-core SoC, 2.5 GHz by burst enabled
BIOS
American Megatrends Inc. UEFI (Unified Extensible Firmware Interface)
BIOS.
System Memory
One 204-pin DDR3L-1866 SO-DIMM, up to 8GB.
1.2.2 I/O System
One HDMI with max. resolution up to 4K x 2K (3840x2160) @ 30Hz
Two RJ-45 connectors for 10/100/1000Base-T Ethernet ports (Intel® I211IT)
Four USB 3.0 & Two USB 2.0 ports
Four COM DB9 connectors, COM1-2 for RS-232/422/485, COM3-4 for RS-232
One phoenix type connector for 9~36VDC power input
One SIM slot
Two PCI Express Mini Card Slots
Two Indicators (Green LED: System Power, Yellow LED: HDD/SSD Active)
Four SMA type connector openings for Antenna
One AT/ATX mode quick switch
One ATX Power Button
One Flexible I/O Windows®for optional mPCIe kits

eBOX627-312-FL User’s Manual
Introduction
3
1.2.3 System Specification
Watchdog Timer
Reset: 1sec. ~ 65535sec./min. and 1sec. or 1min./step
Power Supply
9~36VDC Wide range power input
Operation Temperature
Burst Mode (Default):
-20°C ~ +65°C (-4°F ~ +149°F) (with W.T. SSD/DRAM for 9~36 VDC)
Non-burst Mode:
-20°C ~ +70°C (-4°F ~ +158°F) (with W.T. SSD/DRAM for 12 or 24 VDC)
Storage Temperature
-40℃~ 80℃(-40 ºF ~ 176ºF)
Humidity
10% ~ 95% (non-condensation)
Vibration Endurance
3Grm w/ SSD™(5-500Hz, X, Y, Z directions)
Weight
1.38kg(3.04lb) without package/ 2.08kg(4.59lb) with package
Dimensions
200mm (7.87”) (W) x 120mm (4.72”) (D) x 65mm(2.55") (H)
1.2.4 Driver CD Content
Driver
Chipset
Ethernet
Graphic
USB 3.0
Manual
User Manual
Quick Manual
NOTE:All specifications and images are subject to change without notice.

eBOX627-312-FL User’s Manual
Introduction
4
1.3 Dimensions
The following diagrams show you dimensions and outlines of the eBOX627-312-FL.
1.3.1 System Dimension

eBOX627-312-FL User’s Manual
Introduction
5
1.3.2 Wall mount Bracket Dimension

eBOX627-312-FL User’s Manual
Introduction
6
1.3.3 Din-rail mount Bracket Dimension

eBOX627-312-FL User’s Manual
Introduction
7
1.3.4 VESA mount Bracket Dimension

eBOX627-312-FL User’s Manual
Introduction
8
1.4 I/O Outlets
The following figures show you I/O outlets on front view of the eBOX627-312-FL.
Front View
Front View drawing

eBOX627-312-FL User’s Manual
Introduction
9
Rear View
Rear View drawing

eBOX627-312-FL User’s Manual
Introduction
10
1.5 Packing List
The package bundled with your eBOX627-312-FL should contain the following items:
eBOX627-312-FL System Unit x 1
eBOX627-312-FL Quick Manual x 1
CD x 1 (For Driver and User’s Manual)
2-pin Terminal Block Connector x 1
Screws Pack x 1
Pre-installed Foot pad x 4
DRAM Thermal Pad x 1
HDMI Cable Locking Clip (optional)
Wall-mount Brackets (optional)
VESA-mount Bracket (optional)
Din-rail Bracket (optional)
2.5” SATA Storage (optional)
mSATA Storage Device (optional)
DDR3L SODIMM (optional)
WIFI / 3G / LTE Modules (optional)
If you cannot find this package or any items are missing, please contact Axiomtek distributors
immediately.
1.6 Model List
eBOX627-312-FL-N3350-DC
Fanless Embedded System with Intel®Celeron®
N3350 2.4 GHz, 1 HDMI, 2 GbE LANs,
6 USB, 4 COM and 9 ~ 36 VDC
eBOX627-312-FL-N4200-DC
Fanless Embedded System with Intel®Pentium®
N4200 2.5 GHz, 1 HDMI, 2 GbE LANs,
6 USB, 4 COM and 9 ~ 36 VDC

eBOX627-312-FL User’s Manual
Hardware Installation
11
CHAPTER 2
HARDWARE INSTALLATION
The eBOX627-312-FL is convenient for your various hardware configurations, such as
Memory Module, HDD (Hard Disk Drive), SSD (Solid State Drive), Flexible I/O and mSATA.
The chapter 2 will show you how to install the hardware.
2.1 Installing the Memory module
Step 1 Turn off the system, and unplug the power cord.
Step 2 Turn the system upside down to locate screws at the side of the system, and
then loosen four screws.
Step 3 Remove both of the bottom cover and HDD/SSD cover, please follow
instruction below.
Step 4 Locate the DDR3L SO-DIMM slot, and apply the thermal pad on the
board.

eBOX627-312-FL User’s Manual
Hardware Installation
12
Step 5 Holding the DDR3L SO-DIMM at a 30 degree angle up from horizontal,
slowly insert the golden fingers into the DDR3L SO-DIMM slot until it is
fully inserted in.
Step 6 Press it down gently, until it is firmly seated by locking two latches on
the sides.