AXIOMTEK eBOX622-830-FL Series User manual

eBOX622-830-FL Series
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
November 2013, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The eBOX622-830-FL does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the eBOX622-830-FL before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the eBOX622-830-FL is properly grounded.
4. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen.
6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -20℃or above 80℃. It may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static electricity
on your body.
When handling boards and components, wear a wrist-grounding strap, available from
most electronic component stores.

iv
Classification
1. Degree of production against electric shock : not classified
2. Degree of protection against the ingress of water : IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air
or with oxygen or nitrous oxide.
4. Mode of operation : Continuous

v
General Cleaning Tips
You may need the following precautions before you begin to clean the computer. When you
clean any single part or component for the computer, please read and understand the details
below fully.
When you need to clean the device, please rub it with a piece of dry cloth.
1. Be cautious of the tiny removable components when you use a vacuum cleaner to
absorb the dirt on the floor.
2. Turn the system off before you start to clean up the component or computer.
3. Never drop the components inside the computer or get circuit board damp or wet.
4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of
cleaning. Some individuals may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the computer.
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
your computer and peripherals users can also use household items to clean their computers
and peripherals. Below is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be able to be cleaned using a
product designed for cleaning that component, if this is the case it will be mentioned in the
cleaning.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend you
to rub it with a piece of cloth.
Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or
rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the
plastics parts.
Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of
a computer can be one of the best methods of cleaning a computer. Over time these
items can restrict the airflow in a computer and cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools
for wiping hard to reach areas in your keyboard, mouse, and other locations.
Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs.
Note We strongly recommended that you should shut down the system before you start
to clean any single components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable

vi
Scrap Computer Recycling
If the computer equipment’s needs the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well, please
contact your Axiomtek distributor for recycling and we will make the proper arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines
Corporation.
Intel® and Pentium® are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBasic are trademarks of Microsoft Corporation.
Windows 7, Windows Vista, Windows XPE, Windows XP, Windows WinCE
embedded, Linux, MS-DOS, Microsoft C and Other brand names and trademarks are
the properties and registered brands of their respective owners.

vii
Table of Contents
Disclaimers.............................................................................................................. ii
Safety Precautions................................................................................................. iii
Classification.......................................................................................................... iv
General Cleaning Tips ............................................................................................ v
Scrap Computer Recycling.................................................................................... vi
CHAPTER 1 INTRODUCTION ........................................................................1
1.1 General Description............................................................................ 2
1.2 System Specifications........................................................................ 3
1.2.1 CPU .................................................................................................................... 3
1.2.2 I/O System ......................................................................................................... 3
1.2.3 System Specification........................................................................................ 3
1.2.4 Driver CD Content............................................................................................. 5
1.3 System Dimensions............................................................................ 6
1.4 I/O Outlets ........................................................................................... 7
1.5 Packing List......................................................................................... 9
1.6 Model List.......................................................................................... 10
CHAPTER 2 HARDWARE INSTALLATION..................................................11
2.1 Installing the Memory Module.......................................................... 11
2.2 Installing the SATA HDD................................................................... 15
2.3 Installing the CFast™....................................................................... 19
2.4 Installing the Express Mini Card...................................................... 21
2.5 Installing the Wall Mount (Optional)................................................ 23
2.6 Installing the VESA Mount (optional) .............................................. 26
2.7 Installing the Din-Rail Mount (optional) .......................................... 29
CHAPTER 3 Jumper Setting & Connector.................................................33
3.1 SBC layout......................................................................................... 33
3.2 Jumper Settings................................................................................ 35
3.2.1 Auto Power On (JP4) ...................................................................................... 36
3.2.2 Restore BIOS Optimal Defaults (JP3) ........................................................... 36
3.3 Connectors........................................................................................ 37
3.3.1 Wide Range DC Power In Connector............................................................ 38
3.3.2 COM1~COM6 Serial Port Connector............................................................. 38
3.3.3 VGA Connector ............................................................................................... 40
3.3.4 HDMI Connector.............................................................................................. 40
3.3.5 LAN Connector (LAN1, LAN2)........................................................................ 41
3.3.6 USB Connector ............................................................................................... 41
3.3.7 ATX Power On/OFF Button............................................................................ 41
3.3.8 Audio Connector............................................................................................. 42
3.3.9 Remote Power On/Off Connector.................................................................. 42
3.3.10 SATA Connector ............................................................................................. 42
3.3.11 SATA Power Connector.................................................................................. 43
3.3.12 CFast™ Socket................................................................................................ 44
3.3.13 DDR3 SODIMM Socket ................................................................................... 44

viii
3.3.14 Express Mini Card Slot................................................................................... 45
3.3.15 SIM Card Slot................................................................................................... 46
CHAPTER 4 AMI BIOS SETUP UTILITY......................................................47
4.1 Starting.............................................................................................. 47
4.2 Navigation Keys................................................................................ 47
4.3 Main Menu......................................................................................... 48
4.4 Advanced Menu................................................................................. 49
4.5 Chipset Menu .................................................................................... 56
4.6 Boot Menu ......................................................................................... 59
4.7 Security Menu ................................................................................... 60
4.8 Save & Exit Menu.............................................................................. 61
CHAPTER 5 Drivers Installation .................................................................63
5.1 Installing Chipset Driver................................................................... 63
5.2 Installing Graphics Media Accelerator Driver................................. 66
5.3 Installing Ethernet Driver ................................................................. 70
5.4Installing Audio Driver...................................................................... 72
Appendix A Watchdog Timer.....................................................................75
About Watchdog Timer .................................................................................... 75
How to Use Watchdog Timer........................................................................... 75
Sample Program............................................................................................... 77

eBOX622-830-FL Series User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the eBOX622-830-FL.
The Chapter 1 includes the following sections:
General Description
System Specification
Dimensions
I/O Outlets
Packing List

eBOX622-830-FL Series User’s Manual
Introduction
2
1.1 General Description
The eBOX622-830-FL is an embedded system that supports onboard dual core
Intel®Atom™processor D2550 (1.86 GHz) or N2600 (1.6GHz) processor to provide
Windows 7, Windows 7 Embedded or Linux, suitable for the most endurable
operation. It features fan less design with full feature I/O, one 204-pin unbuffered
SODIMM socket for single channel DDR3-800/1066 MHz memory, and enhanced
system dependability by built-in Watchdog Timer.
Features
1. Intel® NM10 chipset
2. Support Intel® Atom™ Processor D2550 (1.86 GHz) or N2600 (1.6GHz)
3. Maximum to 4GB DDR3 800/1066 MHz memory for D2550; 2GB DDR3 800MHz
memory for N2600.
4. Ultra slim and compact design
5. VGA and HDMI dual independent graphic display
6. Supports 6 USB 2.0 ports
7. Supports 3 RS-232/422/485 and 3 RS-232
8. Supports dual 10/100/1000Mbps Ethernet ports
9. One 2.5” SATA HDD drive bay
10. One front access CFast
11. Watchdog timer
12. One wide-range 10~30V DC-in cinnector
13. 60W AC-DC Adapter (optional)
14. Din-rail mount (optional)
15. Wall mount (optional)
16. VESA mount (optional)
17. Express Mini Card Module (optional)
18. Antenna (optional)
Reliable and Stable Design
The eBOX622-830-FL adopts the advanced cooling system and supporting the CFast™,
which makes it especially suitable for vibration environments, best for industrial
automation, digital signage and gaming application.
Embedded O.S. Supported
The eBOX622-830-FL not only supports Windows 8, Windows 7, Windows Vista, but
also supports embedded OS, such as Windows 7 Embedded and Windows 8 Embedded.
Various Storage devices supported
For storage device, the eBOX622-830-FL supports one 2.5" SATA storage drive bay, and
one CFast™ slot.

eBOX622-830-FL Series User’s Manual
Introduction
3
1.2 System Specifications
1.2.1 CPU
CPU
Intel®AtomTM dual core D2550 1.86 GHz.
Intel®AtomTM dual core N2600 1.6 GHz
Chipset
Intel® NM10 chipset
BIOS
American Megatrends Inc. UEFI (Unified Extensible Firmware Interface)
BIOS.
16Mbit SPI Flash, DMI, Plug and Play.
RPL/PXE Ethernet Boot ROM.
System Memory
One 204-pin unbuffered DDR3 SO-DIMM socket.
Maximum to 4GB DDR3 1066MHz memory for D2550/N2800.
Maximum to 2GB DDR3 800MHz memory for N2600.
1.2.2 I/O System
Six 9-pin D-Sub male connectors, COM1, COM5~COM6 for RS-232/422/485,
COM2~COM4 for RS-232
One 15-pin D-Sub female connector for VGA
One HDMI
Two Audio connectors for Mic-IN and Line-OUT
Two RJ-45 connectors for 10/100/1000Base-T Ethernet
Six USB 2.0 connectors
One 10~30V DC Jack for power input connector
Two Indicators (System Power, HDD Active)
1.2.3 System Specification
Watchdog Timer
1~255 seconds or minutes; up to 255 levels.
DC input
10~30V wide range DC-in phoenix connector
AC/DC Power kit (optional)
External 110~220V AC-in to 12V@5A, 60W AC/DC power adapter
Operation Temperature
-10℃~ 60℃(14 ºF ~ 140ºF), D2550 with W.T. SSD
Storage Temperature
-20℃~ 80℃(-4 ºF ~ 176ºF)
Humidity
10% ~ 90% (non-condensation)
Vibration Endurance
3Grm w/ CFast (5-500Hz, X, Y, Z directions)

eBOX622-830-FL Series User’s Manual
Introduction
4
Weight
1.98 kg (4.36 lb) without package
2.6 kg (17.64 lb) with package
Dimensions
200mm(7.87”) (W) x 120mm(4.72”) (D) x 55.8mm(2.2”) (H)

eBOX622-830-FL Series User’s Manual
Introduction
5
1.2.4 Driver CD Content
Driver
Audio
Chipset
Ethernet
Graphic
TPM
uAPI
Manual
User Manual
Quick Manual
Note: All specifications and images are subject to change without notice.

eBOX622-830-FL Series User’s Manual
Introduction
6
1.3 System Dimensions
The following diagrams show you dimensions and outlines of the eBOX622-830-FL.

eBOX622-830-FL Series User’s Manual
Introduction
7
1.4 I/O Outlets
The following figures show you I/O outlets on front view of the eBOX622-830-FL.
Front View
Front View drawing
2 x USB 2.0
Connectors
SMA type
Antenna holes
Audio
connectors
Power & HDD
Active Indicators
Remote Power on/off
Switch
ATX Power
Switch

eBOX622-830-FL Series User’s Manual
Introduction
8
Rear View
Rear View drawing
VGA
connectors
4 x USB 2.0
connectors
2 x RJ45
LAN
COM1/2/3/4/5/6
Connectors
10~30V DC input
connector
HDMI
connector
CFast
Cover

eBOX622-830-FL Series User’s Manual
Introduction
9
1.5 Packing List
The package bundled with your eBOX622-830-FL should contain the following items:
eBOX622-830-FL System Unit x 1
eBOX622-830-FL Quick Manual x 1
CD x 1 (For Driver and User’s Manual)
Screws pack x1
Foot pad x4
CFast™card Handhold Mylar x1
DRAM Thermal pad x2
AC-DC kit (optional)
Power Cord (optional)
Wall-mount Brackets (optional)
VESA-mount Bracket (optional)
Din-rail Bracket (optional)
2.5”SATA Storage (optional)
CFast™card (optional)
DDR3 SODIMM (optional)
PCI Express Mini Card (optional)

eBOX622-830-FL Series User’s Manual
Introduction
10
1.6 Model List
eBOX622-830-FL-D2550-1.86G-
DC
Fanless embedded system with Intel® ATOM® D2550
1.86GHz dual core processor, VGA, HDMI, USB2.0*4,
LAN*2,RS-232/422/485*3, Rs-232*3, DC10~30V input
eBOX622-830-FL-N2600-1.6G-DC
Fanless embedded system with Intel® ATOM® N2600
1.6GHz dual core processor, VGA, HDMI, USB2.0*4,
LAN*2,RS-232/422/485*3, Rs-232*3, DC10~30V input
If you cannot find this package or any items are missing, please contact Axiomtek distributors
immediately.

eBOX622-830-FL Series User’s Manual
Hardware Installation
11
CHAPTER 2
HARDWARE INSTALLATION
The eBOX622-830-FL is convenient for your various hardware configurations, such as
Memory Module, HDD (Hard Disk Drive), SSD (Solid State Drive) and CFastTM card. The
chapter 2 will show you how to install the hardware.
2.1 Installing the Memory Module
Step 1 Turn off the system, and unplug the power cord.
Step 2 Turn the system upside down to locate screws at the bottom, loosen
screws.
Step 3 Remove the bottom cover and Loosen screws of HDD bracket

eBOX622-830-FL Series User’s Manual
Hardware Installation
12
Step 4 Remove the HDD bracket
Step 5 Locate the memory module, insert the gold colored contact into the
socket.