Backyard Creations EDISON 272-1955 User manual

Thank you for your purchase!
SKU#272-1955
Please carefully unpack each of the components and hardware. Check the
components against the parts list and make sure there are no missing parts.
Should you have any missing parts please contact our Customer Service
department as shown on the last page of instructions.
For ease of assembly, it is recommended to have 2 or more people and
allow enough time to completely finish the assembly.
Assembly can take 4-6 Hours.
We are proud of this products. Please enjoy it along with the enhanced
outdoor living experience for which it is designed.
EDISON GRILL GAZEBO

PART ITEM DESCRIPTION PART
2
2
2
2
4
4
2
2
2
2
2
2
2
2
2
2
1
1
4
ROOF RIBS 1
A1
A2
B
C
D
E
F
G
I
I5
J
K
PILLAR 1
PILLAR 2
LONG CROSSBEAM
SHORT CROSSBEAM
ROOF RIBS 2
ROOF TOP SUPPORT 1
HSHELF
ROOF BORDER 1
I1 ROOF BORDER 2
I2 ROOF BORDER 3
I3 ROOF TOP BORDER 1
I4 ROOF TOP BORDER 2
I6
ROOF PLATE BORDER 1
ROOF PLATE BORDER 2
ROOF TOP BRACE
J1 ROOF TOP COVER
CORNER PROTECTOR
ROOF TOP SUPPORT 2

PART ITEM DESCRIPTION PART
4
8
4
2
2
4
40
8
36
2
2
2
2
2
2
2
2
CONNECTOR 1
CORNER RIB BRACE
CENTER RIB BRACE
SUPPORT BRACKET 1
FOOT BASE
CLIP
PLASTIC WASHER
ROOF PLATE 2
K1
K3
L
L1
M
O1
P
Q
Q1
R
S
K2
N1
N2
SUPPORT BRACKET 2
CLIP
N3
O
R1
ROOF PLATE 3
ROOF PLATE
1
ROOF PLATE 4
ROOF PLATE 5
ROOF PLATE 6
ROOF PLATE 7
ROOF PLATE 8

ROOF PLATE 9
SHELF 1
ALLEN WRENCH
S1
T
U
V
W
2
2
1
2
1
MIDDLE SHELF
SIDE SHELF
BACK SHELF
AA
BB
CC
DD
EE
FF
GG
85
32
4
32
20
2
1
BOLT (M6 X 15mm)
BOLT (M6 X 23mm) NUT
BOLT (M6 X 42mm) NUT
BOLT (M6 X 12mm) WASHER
BOLT (M6 X 35mm)
HEX WRENCH

1
2
AA x 12 M6*15
DD x 32
STEP 1: Attach Foot Base ( part M) to the Pillars 1, 2 (part A1, A2)
Warning: Do not tighten the bolts completely until end of the frame assembly. Before
assembling the Roof Panels, make sure all bolts of the frame have been tightened.
M
M
AA
AA
AA
STEP 2: Attach Long Crossbeam (part B) and short Crossbeam (part C) to the pillars
1, 2 (part A1, A2)
DD
DD
DD
DD
B
C
C
B
A1
A2
A1
A2
M6*12

STEP 3: Attach the Support Brackets (part L, L1) to the shelf (part H) and pillar (part A1,A2).
STEP 4: Attach the Corner Protector (part K).
L× 2 L1× 2
K× 4

STEP 5: Assemble the Roof Frame by attaching the Roof Ribs 1 (part D) to the Roof Top Brace (part J)
as shown in the diagram.
STEP 6: Attach the roof to the gazebo frame.
4
AA

7
8
AA x 8 M6 x 15
AA x 4 M6 x 15
STEP 7: Attach the Roof Top Support 1 (part G) and Roof Top Support 2 (part F)
using Connector (part K1).
STEP 8: Attach the assembled Roof Top Support to the Roof Ribs (part D).
AA
F
G
D
Lift the partially assembled Roof to the assembled frame and attach as shown
in the diagram.

STEP 9: Attach the Roof Ribs 2 (part E) to the assembled Roof Top Support (part G,F).
STEP 10: Attach the Clips (part N1) and Clips (part N2)
to the Roof Plates 6,7,8,9 (part R,R1,S,S1)as
Install the Roof Plates on the Long Sides
Start by sliding Roof Plate 6 (part R)
and slide Roof Plate 7 (part R1) into position.
Attached the Roof Ribs (part E) to the assembled frame as shown in the diagram.
shown in the diagram.
Work your way from left to right.
Plate 7(part R1) as shown in the diagram.
F/G
into position. Then overlap Roof
of the Gazebo.
Install the Roof Plates on the short Sides of the Gazebo.
and slide Roof Plate 9 (part S1) into position.
Work your way from left to right. Start by sliding Roof Plate 8 (part S)
into position. Then overlap Roof plate 9 (part S1) as shown in the diagram
S× 2 S1× 2 R× 2 R1× 2 N1× 8 N2× 8

STEP 11: Attach Roof Top Borders 1 (part I3) to the long edge of the Roof and Roof Top Borders 2 (part I4) to the
short edge of the roof.
Attach the Corner Rib Brace (part K2) as shown in the diagram.
STEP 12: Attach the Roof Top Cover (part J1) to the Roof Top Brace (part J)
K2× 4