Backyard Creations PERG-1111 User manual

1of11
Owner’s Manual
10’ x 10’ Brunson Pergola
Model Number: PERG-1111
SKU Number: 272-1153
Note: This pergola frame is designed to be used as a permanent fixture on level surface.

2of11
Parts List
10’ x 10’ Brunson Pergola
Letter
Illustration
Description
Qty.
A1
Corner Post
2
A2
Corner Post
2
B
Roof Panel
7
C1
Panel Connecting Rod
1
C2
Rotating Device
1
D
Lintel w/Rotating Device
1
D1
Front Lintel
1
E
Side Lintel
2
F
Corner Post Brace
8
G
Roof Adjustment Pole
1
H
Base Plate
4

3of11
Letter
Illustration
Description
Qty.
I
Base Cover
4
J
Roof Panel Connectors
13
K
Rotating Device Connector
1
L
Pull-Down Screen
2
M
M6 x 15mm Bolt with Washer
78
N
M6 x 75mm Bolt with Washer
8
O
M6 x 15mm Bolt
20
P
Self-Tapping Screw
4
Q
M6 Open Wrench
1
R
Allen Wrench
1
S
Allen Wrench
1
T
Ground Stake
16

4of11
Assembly Instructions
10’ x 10’ Brunson Pergola
Note: For video instructions please visit:
https://insideout.store/video-assembly-instructions/
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact InSide Out Customer Support. See page 11.
⚫Assemble on a stable level surface to avoid damage to gazebo and possible injury.
⚫Two people are required to assemble this product.
⚫Pergola dimensions are measured from end of corner post base covers.
WARNING: TIGHTEN BOLTS AFTER EACH STEP ONCE PARTS ARE ALIGNED!
Step 1: Insert Corner Posts (A1 & A2) into Base Cover (I). Attach Base Plate (H) to Corner Posts (A1 & A2)
using Bolt (M). See Figure 1.
Figure 1

5of11
Step 2: Attach Side Lintel (E) and Front Lintel (D and D1) to the Corner Posts (A1 & A2) using Bolt (M).
See Figure 2.
Note: Make sure the holes on the Front Lintel (D and D1) are facing inwards.
Figure 2

6of11
Step 3: Attach all Corner Post Braces (F) to the Corner Posts (A1 & A2) and the Lintels (D/D1/E) using
Bolts (M). See Figure 3.
Figure 3
Step 4: Attach Roof Panel Connectors (J) to the interior of the Front Lintel (D1) and Lintel with Rotating
Device (D) using Bolts (O). See Figure 4-1.
Attached Rotating Device (C2) to exterior of Lintel with Rotating Device (D) with Bolts (M). See
Figure 4-2.
Figure 4-1
Figure 4-2

7of11
Step 5: Insert Rotating Device Connector (K) into the middle hole of Lintel with Rotating Device (D). See
Figure 5.
Step 6: Attach Roof Panels (B) to the Roof Panel Connectors (J) using Bolts (M). See Figure 6-1. Attach
Rotating Device Connector (K) to Roof Panel (B) using Bolts (M). See Figure 6-2.
Figure 5
Figure 6-1
Figure 6-2

8of11
Step 7: Connect the Panel Connecting Rod (C1) to each Roof Panel (B) using Bolts (O). See Figure 7.
Figure 7

9of11
Step 8: Attach Pull-Down Screen (L) to the Side Lintel (E) using Bolts (N). Repeat for opposite side. See
Figure 8-1.
Attached the plastic anchor on the Pull-Down Screen (L) to the Post (A1) by Self-Tapping Screw
(P). See Figure 8.2.
Figure 8-1
Figure 8-2

10 of11
Step 9: Secure Pull-Down Screen (L) to Corner Posts (A1 & A2). See Figure 9. Insert the Stake (T) into
the ground through Base Plate (H) to fix the gazebo. See Figure 10.
Note: Please see our video for additional assembly assistance:
https://insideout.store/video-assembly-instructions/
Figure 9
Figure 10

11 of11
Care & Maintenance
Maintain your outdoor gazebo by removing the canopies and storing out of the elements when not in use, or
during hazardous weather conditions (wind, rain, snow, etc.).
Frame: Clean frames with a mild soap and warm water. Do not use abrasive materials, cleaners or bleach.
Rinse with clean water and dry thoroughly. Always clean, drain and dry thoroughly before storing
for the winter.
Fabric: Pergola pull down shades and textilene fabric, may be cleaned by hand with a mild solution of soap
and water. Rinse thoroughly and allow to drip dry. Do not use bleach or solvents on fabrics.
Warranty
You must retain the original receipt to obtain warranty service.
What is covered?
Frame: Frame is warranted against rusting for 1-year
Finish: Frame Finish is warranted against peeling, cracking or blistering for 1-year if the product has not
been scratched or abrade.
Fabric: Pull down shades and textilene fabric are covered by a 1-year warranty against manufacturing
defects.
What is not covered?
EXCLUSIONS: Pergola use for commercial, contract, or other non-residential purposes, damage due to acts
of nature, vandalism, misuse, or improper assembly are not covered. Discoloration or fading of the finish or
fabrics as a result of chemicals or spills, pool water chemicals or salt water is not covered. Mildew of fabric is
not covered. Corrosion and rusting of frames resulting from scratches are not covered. If within the stated
warranty period this product is found to be defective in material or workmanship, the purchaser must contact
the manufacturer’s customer service department. The manufacturer, at its option, will repair or replace the
defective parts. Proof of purchase (dated register receipt) is required for warranty claims. It remains the
customer’s responsibility to pay for freight and packing charges to and from the service center. Warranty is
to the original purchaser and is non-transferable. Any replacement of warranted items will be in the original
style and color, or similar style and color if the original is unavailable or has been discontinued.
Questions, problems, missing or damaged part? Before returning to the store call or email our Customer
Service.
Customer Service Contact Information:
Hours: Monday - Friday 8:00 a.m. - 5:00 p.m. Central Time (CT)
Phone: [phone]
Email: servic[email protected]