Backyard Creations Palm Springs PS-6PC-SG User manual

1of14
Owner’s Manual
Palm Springs
6-Piece Seating Group
Model Number: PS-6PC-SG
SKU Number: 272-1910

2of14
Parts List – Swivel Rockers (2)
Letter
Illustration
Description
Qty.
Letter
Illustration
Description
Qty.
A
Left Arm
2
J
M8 Nut
8
B
Right Arm
2
K
M6 Bolt Cap
16
C
Seat and Back
2
L
M6 Nut Cap
4
D
Swivel Rocker
Base
2
M
Seat Cushion
2
E
Swivel Base
Connector
4
N
Back Cushion
2
F
M6 x 15mm Bolt
8
O
Allen Wrench
2
G
M6 x 42mm Bolt
4
P
#12
Open Wrench
2
H
M8 x 40mm Bolt
8
Q
#14
Open Wrench
2
I
M6 Washer
12

3of14
Assembly Instructions
Swivel Rockers (2)
Note: For video instructions please visit:
https://insideout.store/video-assembly-instructions/
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact InSide Out Customer Support. See page 14.
⚫Assemble product on a soft and non-abrasive surface, such as carpet to avoid damaging the item.
⚫Two people are required to assemble heavy items.
WARNING: DO NOT TIGHTEN BOLTS UNTIL NOTED AFTER EACH STEP!
Step 1: Attach Right Arm (B) to the Back of Part (C) using one Bolt (G) and Washers (I). See Figure 1-1.
Step 2: Attach Right Arm (B) to the Seat of Part (C) using two Bolts (F) and Washers (I). See Figure 1-2
Repeat Step 1 and Step 2 for the Left Arm (A). Check alignment and make adjustments if necessary.
Tighten bolts with Allen Wrench (O).

4of14
Step 3: Connect the Bottom Seat Bracket on Seat-and-Back (C) to the “Back” position of the Swivel Plate
on Swivel Base (D) with Bolts (H), Swivel Base Connector (E), and Nuts (J). See Figure 2. Tighten
bolts using Open Wrench (P & Q).
Figure 2
Step 4: Add Bolt Caps (K & L) to Bolts (F, G & H). Place the Seat Cushion (M) and the Back Cushion (N)
on the chair frame and tighten straps. See Figure 3. Your swivel rocker is ready for use. Enjoy!
Note: Cushions for Swivel Rocker are different sizes than cushions for Loveseat.
Figure 3
Note: Please see our video for additional assembly assistance:
https://insideout.store/video-assembly-instructions/

5of14
Parts List – Loveseat
Letter
Illustration
Description
Qty.
Letter
Illustration
Description
Qty.
A
Left Arm
1
G
M6 Washer
10
B
Right Arm
1
H
M6 Bolt Cap
10
C
Back
1
I
Allen Wrench
1
D
Seat
1
J
Seat Cushion
2
E
M6 x 15 mm Bolt
4
K
Back Cushion
2
F
M6 x 42 mm
Bolt
6

6of14
Assembly Instructions
Loveseat
Note: For video instructions please visit:
https://insideout.store/video-assembly-instructions/
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact InSide Out Customer Support. See page 14.
⚫Assemble product on a soft and non-abrasive surface, such as carpet to avoid damaging the item.
⚫Two people are required to assemble heavy items.
WARNING: DO NOT TIGHTEN BOLTS UNTIL NOTED AFTER EACH STEP!
Step 1: Attach Left Arm (A) to Seat (D) using Bolts (F), Bolt (E), and Washers (G). Repeat for Right Arm
(B). See Figure 1A and Figure 1B. Do not tighten bolts until after Step 3.
Figure 1A
Figure 1B

7of14
Step 2: Attach Seat (D) to Back (C) using Bolts (E) and Washers (G). See Figure 2. Do not tighten bolts
until after Step 3.
Step 3: Connect Left Arm (A) and Right Arm (B) to Back (C) using Bolts (F) and Washers (G). See Figure
3A and 3B. Check alignment and make adjustment if necessary. Tighten all bolts with Allen
Wrench (I).
Step 4: Add Bolt Caps (H) to Bolts (E & F). Place Seat Cushion (J) and Back Cushion (K) on Loveseat and
tighten straps. Your Loveseat is complete and ready for use. Enjoy!
Figure 4
Note: Please see our video for additional assembly assistance:
https://insideout.store/video-assembly-instructions/
Figure 2
Figure 3A
Figure 3B

8of14
Parts List – Coffee Table
Letter
Illustration
Description
Qty.
Letter
Illustration
Description
Qty.
A
Tabletop
1
G
Nut
4
B
Table Leg
4
H
M6 Bolt Cap
12
C
Leg Brace
1
I
M6 Nut Cap
4
D
M6 x 15 mm Bolt
8
J
Allen Wrench
1
E
M6 x 35 mm
Bolt
4
K
Wrench
1
F
M6 Washer
12

9of14
Assembly Instructions
Coffee Table
Note: For video instructions please visit:
https://insideout.store/video-assembly-instructions/
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact InSide Out Customer Support. See page 14.
⚫Assemble product on a soft and non-abrasive surface, such as carpet to avoid damaging the item.
⚫Two people are required to assemble heavy items.
WARNING: DO NOT TIGHTEN BOLTS UNTIL NOTED AFTER EACH STEP!
Step 1: Place Tabletop (A) upside down on a soft non-abrasive surface. Attach Table Legs (B) to Tabletop
(A) using Bolts (D) and Washers (F). Do not tighten bolts until after Step 2. See Figure 1.
Figure 1

10 of14
Step 2: Attach Leg Brace (C) to Table Legs (B) using Bolt (E), Washer (F) and Nut (G). Tighten all Bolts
(D and E) using Allen Wrench (J) and Wrench (K), attach Bolt Caps (H) and Nut Caps (I).
Figure 2
Step 3: Turn the assembled table upright. You Coffee Table is complete and ready for use. Enjoy!
Figure 3
Note: Please see our video for additional assembly assistance:
https://insideout.store/video-assembly-instructions/

11 of14
Parts List – Side Tables (2)
Letter
Illustration
Description
Qty.
Letter
Illustration
Description
Qty.
A
Tabletop
2
G
Nut
8
B
Table Leg
8
H
M6 Bolt Cap
24
C
Leg Brace
2
I
M6 Nut Cap
8
D
M6 x 15 mm Bolt
16
J
Allen Wrench
2
E
M6 x 35 mm
Bolt
8
K
Wrench
2
F
M6 Washer
24

12 of14
Assembly Instructions
Side Tables (2)
Note: For video instructions please visit:
https://insideout.store/video-assembly-instructions/
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact InSide Out Customer Support. See page 14.
⚫Assemble product on a soft and non-abrasive surface, such as carpet to avoid damaging the item.
⚫Two people are required to assemble heavy items.
WARNING: DO NOT TIGHTEN BOLTS UNTIL NOTED AFTER EACH STEP!
Step 1: Place Tabletop (A) upside down on a soft non-abrasive surface. Assemble Table Legs (B) to
Tabletop (A) using Bolts (D) and Washers (F). See Figure 1. Do not tighten bolts until after
Step 2.
Figure 1

13 of14
Step 2: Attach Leg Brace (C) to Table Legs (B) using Bolts (E), Washers (F) and Nuts (G). See Figure 2.
Tighten all bolts using Allen Wrench (J) and Open Wrench (K), attach Bolt Caps (H) and Nut
Caps (I).
Figure 2
Step 3: Turn the assembled table upright. Your Side Table is complete and ready for use. Enjoy!
Figure 3
Note: Please see our video for additional assembly assistance:
https://insideout.store/video-assembly-instructions/

14 of14
Care & Maintenance
Maintain your outdoor furniture by using furniture covers or storing out of the elements when not in use.
Frame: Clean frames with a mild soap and warm water. Do not use abrasive materials, cleaners or
bleach. Rinse with clean water and dry thoroughly. Always clean, drain and dry thoroughly
before storing for the winter.
Tabletop: Clean the tabletop with a soft, clean white cloth or sponge. Never use scouring creams, abrasive
cleaners, acid or petroleum-based products. Wash with warm water and dry thoroughly after
cleaning to prevent buildup of any residue from minerals that might be present in your water,
even with softened water.
Fabric: Cushions may be cleaned by hand with a mild solution of soap and water. Rinse cushions
thoroughly, stand on end and allow to drip dry. Do not machine wash or tumble dry, as
cushions may shrink. Do not use bleach or solvents on fabrics.
Warranty
You must retain the original receipt to obtain warranty service.
What is covered?
Frame: Frame is warranted against rusting for 1-year
Finish: Frame is warranted against peeling, cracking or blistering for 1-year if the product has not been
scratched or abraded.
Fabric: Cushions are covered by a 1-year warranty against manufacturing defects.
Glass: Tempered glass tabletops are not covered against breakage.
What is not covered?
EXCLUSIONS: Furniture used for commercial, contract, or other non-residential purposes, or items
damaged due to acts of nature, vandalism, misuse, or improper assembly are not covered. Discoloration or
fading of the finish or fabrics as a result of chemicals or spills, pool water chemicals or salt water is not covered.
Mildew of fabric is not covered. Glass breakage is not covered. Corrosion and rusting of frames resulting from
scratches are not covered. If within the stated warranty period this product is found to be defective in material
or workmanship, the purchaser must contact the manufacturer’s customer service department. The
manufacturer, at its option, will repair or replace the defective parts. Proof of purchase (dated register receipt)
is required for warranty claims. It remains the customer’s responsibility to pay for freight and packing charges
to and from the service center. Warranty is to the original purchaser and is non-transferable. Any replacement
of warranted items will be in the original style and color, or similar style and color if the original is unavailable
or has been discontinued.
Questions, problems, missing or damaged part? Before returning to the store call or email our Customer
Service.
Customer Service Contact Information:
Hours: Monday - Friday 8:00 a.m. - 5:00 p.m. Central Time (CT)
Phone: [phone]
Email: servic[email protected]