Balluff BNI IOL-709-000-K006 User manual

BNI IOL-709-000-K006
BNI IOL-710-000-K006
IO-Link Sensor-Hub analog
User’s Guide

www.balluff.com
1
Content
1Notes to the user 2
1.1 About this guide 2
1.2 Structure of the guide 2
1.3 Typographical conventions 2
Enumerations 2
Actions 2
Syntax 2
Cross-references 2
1.4 Symbols 2
1.5 Abbreviations 2
2Safety 3
2.1 Intended use 3
2.2 Installation and startup 3
2.3 General safety instructions 3
Hazardous voltage 3
3Getting Started 4
3.1 Connection overview 4
3.2 Mechanical connection 5
3.3 Electrical connection 5
3.4 Function ground 5
3.5 IO-Link connection 5
3.6 Digital Sensors 6
3.7 Analogue Sensors 6
4IO-Link Interface 7
4.1 IO-Link Data 7
4.2 Process data inputs 7
4.3 Process data outputs 8
4.4 Parameter data/ On-request data 8
Identification data 8
Inversion 9
Switch point enable 9
Switch point 9
4.5 Errors 10
4.6 Events 10
5Technical Data 11
5.1 Dimensions 11
5.2 Mechanical data 11
5.3 Electrical data 11
5.4 Operating conditions 11
5.5 Function indicators 12
Module LEDs 12
Digital Input LEDs 12
Analogue Input LEDs 12
6Appendix 13
6.1 Type designation code 13
6.2 Order information 13

IO-Link Sensor-Hub
BNI IOL-709-… / BNI IOL-710-…
www.balluff.com
2
1Notes to the user
1.1 About this guide
This guide describes the Balluff IO-Link sensor collector module, also called the Sensor
Hub.
Connection to the host interface master is made through the IO-Link protocol.
Functionally this compact, cost-effective module is comparable with a passive splitter box: It
takes digital and analogue sensor signals and passes them over the IO-Link interface.
1.2 Structure of the
guide
The Guide is organized so that the sections build on one another.
Section 2 : Basic safety information.
Section 3 : The main steps for installing the device.
Section 4: IO-Link, parameter and process data for the device.
Section 5: Technical data for the device..
1.3 Typographical
conventions
The following typographical conventions are used in this Guide.
Enumerations
Enumerations are shown in list form with bullet points.
•Entry 1,
•Entry 2.
Actions
Action instructions are indicated by a preceding triangle. The result of an action is indicated
by an arrow.
Action instruction 1.
Action result.
Action instruction 2.
Syntax
Numbers:
Decimal numbers are shown without additional indicators (e.g. 123),
Hexadecimal numbers are shown with the additional indicator hex (e.g. 00hex).
Cross-references
Cross-references indicate where additional information on the topic can be found (see
Section 5 -"Technical Data“).
1.4 Symbols
Note!
This symbol indicates a security notice which most be observed.
Note tip
This symbol indicates general notes.
1.5 Abbreviations
BCD
BNI
CV
DPP
I-Port
EMC
FE
IOL
LSB
MSB
SP
SPDU
VV
Binary coded switch
Balluff Network Interface
Current Version: BNI IOL 709…
Direct Parameter Page
Digital input port
Electromagnetic Compatibility
Function ground
IO-Link
Least Significant Bit
Most Significant Bit
Switch Point
Service Protocol Data Unit
Voltage version: BNI IOL 710…

www.balluff.com
3
2Safety
2.1 Intended use
The BNI IOL-… is a decentralized sensor input module which is connected to a host IO-Link
master over an IO-Link interface.
2.2 Installation and
startup
Note
Installation and startup are to be performed only by trained specialists. Qualified
personnel are persons who are familiar with the installation and operation of the
product, and who fulfills the qualifications required for this activity. Any damage
resulting from unauthorized manipulation or improper use voids the
manufacturer's guarantee and warranty. The Operator is responsible for
ensuring that applicable of safety and accident prevention regulations are
complied with.
2.3 General safety
instructions
Commissioning and inspection
The operating company shall be responsible for observance of locally applicable safety
instructions.
Before commissioning, carefully read the operating manual.
The system must not be used in applications in which the safety of persons is dependent on
the function of the device.
Authorized Personnel
Installation and commissioning may only be performed by trained specialist personnel.
Intended use
Warranty and liability claims against the manufacturer are rendered void by:
Unauthorized tampering
Improper use
Use, installation or handling contrary to the instructions provided in this operating
manual
Obligations of the Operating Company
The device is a piece of equipment from EMC Class A. Such equipment may generate RF
noise. The operator must take appropriate precautionary measures. The device may only be
used with an approved power supply. Only approved cables may be used.
Malfunctions
In the event of defects and device malfunctions that cannot be rectified, the device must be
taken out of operation and protected against unauthorized use.
Hazardous
voltage
Note
Disconnect all power before servicing equipment.
Note
In the interest of product improvement, the Balluff GmbH reserves the right to
change the specifications of the product and the contents of this manual at any
time without notice.

IO-Link Sensor-Hub
BNI IOL-709-… / BNI IOL-710-…
www.balluff.com
4
3Getting Started
3.1 Connection
overview
1 Mounting hole
2 IO-Link interface
3 Analogue input-Port 1
4 Status-LED: Analogue port
5 Analogue input port 3
6 Status-LED: digital input Pin 2
7 Digital input port 1
8 Status-LED: Digital port Pin 4
9 Digital input port 3
10 Status LED “Power Supply”
11 Digital input port 2
12 Digital input port 0
13 Analogue input port 2
14 Analogue input port 0
15 Label
16 Status-LED „COM“
17 Function ground connection

www.balluff.com
5
3 Getting Started
3.2 Mechanical
connection
The BNI IOL modules are attached using 3 M4 screws (Item 1, Fig. 3-1/3-2).
3.3 Electrical
connection
The Sensor Hub modules require no separate supply voltage connection.
Power is provided through the IO-Link interface by the host IO-Link Master.
3.4 Function ground
The modules are provided with a ground terminal.
Connect Sensor Hub module to the ground terminal.
Note!
The FE connection from the housing to the machine must be low-impedance
and as short as possible.
3.5 IO-Link
connection
The IO-Link connection is made using an M12 connector (A-coded, male).
IO-Link (M12, A-coded, male)
Pin
Function
1
Supply voltage, +24 V, max. 1.6 A
2
-
3
GND, reference potential
4
C/Q, IO-Link data transmission channel
Connection protection ground to FE terminal, if present.
Connect the incoming IO-Link line to the Sensor Hub.
Note!
A standard sensor cable is used for connecting to the host IO-Link Master.

IO-Link Sensor-Hub
BNI IOL-709-… / BNI IOL-710-…
www.balluff.com
6
3 Getting Started
3.6 Digital Sensors
Digital input port (M12, A-coded, female)
Pin
Function
1
+24 V, 100 mA
2
Standard Input
3
0 V, GND
4
Standard Input
5
-
Note!
For the digital sensor inputs follow the input guideline per EN 61131-2,
Type 2.
3.7 Analogue
Sensors
Analogue input port (M12, A-coded, female)
Pin
Function
1
+24 V, 100 mA
2
BNI IOL-709...: 4 - 20 mA
BNI IOL-710…:n.c.
3
0 V, GND
4
BNI IOL-710...: 0 - 10 V
BNI IOL-709…:n.c
5
FE, function ground
Note!
Unused I/O port sockets must be fitted with cover caps to ensure IP67
protection rating.

www.balluff.com
7
4IO-Link Interface
4.1 IO-Link Data
Baudrate
COM2 (38,4 kBaud)
Frame type
1
Minimum cycle time
3 ms
Process data cycle
30 ms with minimum cycle time
4.2 Process data
inputs
BNI IOL-710-…/BNI IOL-709-…(Sensor-Hub digital/analog)
Process data length 10Byte:
Byte 0
Byte 1
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Input
Port 7 Pin 4
Input
Port 6 Pin 4
Input
Port 5 Pin 4
Input
Port 4 Pin4
Switch Point 1
Port 3
Switch Point 1
Port 2
Switch Point 1
Port 1
Switch Point 1
Port 0
Input
Port 7.Pin 2
Input
Port 6.Pin 2
Input
Port 5.Pin 2
Input
Port 4.Pin 2
Switch Point 2
Port 3
Switch Point 2
Port 2
Switch Point 2
Port 1
Switch Point 2
Port 0
Byte 2
Byte 3
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Error 1
Error 2
Error 3
0
MSB
Analogue value
LSB
Port 0
Byte 4
Byte 5
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Error 1
Error 2
Error 3
0
MSB
Analogue value
LSB
Port 1
Byte 6
Byte 7
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Error 1
Error 2
Error 3
0
MSB
Analogue value
LSB
Port 2
Byte 8
Byte 9
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Error 1
Error 2
Error 3
0
MSB
Analogue value
LSB
Port 3

IO-Link Sensor-Hub
BNI IOL-709-… / BNI IOL-710-…
www.balluff.com
8
4 IO-Link Interface
Input:
Input-Signal at Port and Pin
Switch Point:
The switch point bits show a switch point
overrun. The switch point can be configured
by parameter ( see 0.0 - “Switch point
enable” and 0.0 - “Switch point”)
Analogue value:
VV: actual voltage value between
0 and 1056 (1Bit = 0.01V)
CV: actual current value between
0 and 2150 (1Bit = 0.01mA)
Error:
•Error 1
•Error 2
•Error 3
Overcurrent/short circuit on sensor supply
Measurement range overflow
Measurement range undercut (only CV)
4.3 Process data
outputs
There are no outputs at BNI IOL-710-... and BNI IOL-709-... modules.
4.4 Parameter data/
On-request data
DPP
SPDU
Parameter
Data
width
Access
Index
Index
Sub-
index
Identification Data
07hex
Vendor ID
2 Byte
Read only
08hex
09hex
Device ID
3 Byte
0Ahex
0Bhex
10hex
0
Vendor Name
8 Byte
11hex
0
Vendor text
16 Byte
12hex
0
Product Name
34 Byte
13hex
0
Product ID
21 Byte
14hex
0
Product text
34 Byte
16hex
Hardware Revision
3 Byte
17hex
0
Firmware Revision
3 Byte
Identification data
Type
Device ID
Version
BNI IOL-710-000-K006
050201hex
Voltage version
BNI IOL-709-000-K006
050202hex
Current version

www.balluff.com
9
4 IO-Link Interface
DPP
SPDU
Parameter
Data width
Value range
Default-
value
Index
Index
Sub-
index
Parameter Data
10hex
40hex
64
0
1-16
Inversion
2 Byte
0000hex…FFFFhex
0000hex
11hex
12hex
41hex
65
0
1-8
Switch point enable
1 Byte
00hex…FFhex
00hex
42hex
66
0
Switch point 1 Port 0
2 Byte
0000hex … 03E8hex
0000hex
43hex
67
0
Switch point 1 Port 1
2 Byte
0000hex … 03E8hex
0000hex
44hex
68
0
Switch point 1 Port 2
2 Byte
0000hex … 03E8hex
0000hex
45hex
69
0
Switch point 1 Port 3
2 Byte
0000hex … 03E8hex
0000hex
46hex
70
0
Switch point 2 Port 0
2 Byte
0000hex … 03E8hex
0000hex
47hex
71
0
Switch point 2 Port 1
2 Byte
0000hex … 03E8hex
0000hex
48hex
72
0
Switch point 2 Port 2
2 Byte
0000hex … 03E8hex
0000hex
49hex
73
0
Switch point 2 Port 3
2 Byte
0000hex … 03E8hex
0000hex
Inversion
Inversion of the input signals:
Byte 0
Byte 1
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Inversion
Port 7 Pin 4
Inversion
Port 6 Pin 4
Inversion
Port 5 Pin 4
Inversion
Port 4 Pin 4
Inversion
SP1 Port 3
Inversion
SP1 Port 2
Inversion
SP1 Port 1
Inversion
SP1 Port 0
Inversion
Port 7 Pin 2
Inversion
Port 6 Pin 2
Inversion
Port 5 Pin 2
Inversion
Port 4 Pin 2
Inversion
SP2 Port 3
Inversion
SP2 Port 2
Inversion
SP2 Port 1
Inversion
SP2 Port 0
Switch point
enable
Enable the switch points by setting the enable bits
Byte 0
7
6
5
4
3
2
1
0
Enable switch point 2
Port 3
Enable switch point 2
Port 2
Enable switch point 2
Port 1
Enable switch point 2
Port 0
Enable switch point 1
Port 3
Enable switch point 1
Port 2
Enable switch point 1
Port 1
Enable switch point 1
Port 0
Switch point
Byte 0
Byte 1
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
0
0
0
0
Switch point
Value range (dec)
CV= 400…2000
VV= 0…1000

IO-Link Sensor-Hub
BNI IOL-709-… / BNI IOL-710-…
www.balluff.com
10
4 IO-Link Interface
4.5 Errors
Byte 0
Byte 1
Device application error: 80hex
11hex Index not available
12hex Subindex not available
30hex Value out of range
4.6 Events
Class/Qualifier
Code (high + low)
Mode
Type
Instance
Parameter Data
appears
Error
AL
Device
Hardware
supply
Supply low
voltage
U2 = supply + 24V
C0hex
30hex
03hex
5000hex
0100hex
0010hex
0002hex
F3hex
5112hex
disappears
Error
AL
Device
Hardware
supply
Supply low
voltage
U2 = supply + 24V
80hex
30hex
03hex
5000hex
0100hex
0010hex
0002hex
B3hex
5112hex
appears
Error
AL
Device
Hardware
supply
supply periphery
C0hex
30hex
03hex
5000hex
0100hex
0060hex
F3hex
5160hex
disappears
Error
AL
Device
Hardware
supply
supply periphery
80hex
30hex
03hex
5000hex
0100hex
0060hex
B3hex
5160hex

www.balluff.com
11
5Technical Data
5.1 Dimensions
5.2 Mechanical data
Housing Material
Plastic, transparent
IO-Link-Port
M12, A-coded, male
Input-Ports
8x M12, A-coded, female
Enclosure rating
IP67 (only when plugged-in and threaded-in)
Weight
90 g
Dimensions
(L × W × H, excluding connector)
115 × 50 × 30,8 mm
5.3 Electrical data
Operating voltage
18 ... 30,2 V DC, per EN 61131-2
Ripple
< 1 %
Current draw without load
≤ 40 mA
5.4 Operating
conditions
Operating temperature
-5 °C … +55 °C
Storage temperature
-25 °C … +70 °C
EMC
–EN 61000-4-2/3/4/5/6
Severity level 4A/3A/4B/2A/3A
Vibration/shock
EN 60068 part 2-6/27

IO-Link Sensor-Hub
BNI IOL-709-… / BNI IOL-710-…
www.balluff.com
12
5 Technical Data
5.5 Function
indicators
Module LEDs
LED 5, IO-Link Communication
Status
Function
Green
No Communication
Green negative pulsed
Communication OK
Red
Communication line overload
Off
Module unpowered
LED 4, Power supply status
Status
Function
Green
Module power is OK
Green slowly flashing
Short circuit
Green rapidly flashing
Module power supply < 18 V
Off
Module unpowered
Digital Input LEDs
LED 3, Input Pin 4 and LED 2, Input Pin 2
Status
Function
Yellow
Input signal = 1
Off
Input signal = 0
Analogue Input
LEDs
LED 1, Analogue input port
Status
Signal 709 (4-20 mA)
Signal 710 (0-10 V)
Green
≥ 4 mA - ≤ 20 mA
> 0,05 V
Red
< 4 mA - > 20 mA
> 10,05 V

www.balluff.com
13
6Appendix
6.1 Type designation
code
6.2 Order information
Type
Order Code
BNI IOL-709-000-K006
BNI0007
BNI IOL-710-000-K006
BNI0008
BNI IOL-7xx-000-K006
Balluff Network Interface
IO-Link interface
Functions
710 = 8 digital inputs 0,15 A + 4 analog inputs 0 - 10 V
709 = 8 digital inputs 0,15 A + 4 analog inputs 4 - 20 mA
Variant
000 = Standardvariante
Mechanical configuration
K006 =Plastic housing,
Connectors:
- BUS and Power supply: 1x M12x1, external thread
- Input ports: 8x M12x1, internal thread

IO-Link Sensor-Hub
BNI IOL-709-… / BNI IOL-710-…
www.balluff.com
14
Notes

www.balluff.com
www.balluff.com
Balluff GmbH
Schurwaldstrasse 9
73765 Neuhausen a.d.F.
Germany
Tel. [phone]
Fax [phone]
[email protected]
Nr. 910442 E Edition 1311 Subject to modification