Band-it G40269 Giant II User manual

BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
Document # P36187 Rev. G
© Copyright
BAND-IT-IDEX, Inc. 2007
All rights reserved
www.BAND-IT-IDEX.com
Page 1 of 3
G40269 Giant II
Hand Tool
Operating
Instructions
1. Band may be used from bulk roll as this
completely eliminates waste of band. Slide
buckle on band as shown, bringing end of
band around object to be clamped and
again through buckle.
2. Continue band around object once
more and again through buckle.
Double banding develops a great deal
more radial compression than single
banding. Bend end of band under
buckle.
3. Place band in open of tool nose and
gripper block. Move into slot as far as
possible, to avoid buckle sliding into tool
nose. Apply tension by turning handle of
tool.
4. Place finger on BAND-IT Band at buckle
bridge while tensioning with tool handle.
When you feel BAND-IT Band stop moving
through buckle as you are turning handle,
maximum pressure is being exerted by the
BAND-IT Band around object being
clamped. Stop turning handle.
5. Roll tool over buckle, backing off with
tension handle1- 1½ turns throughout entire
rolling operation. Failure to back off tension
with tension handle throughout entire course
of roll-over may result in breaking of band.
There is no loss of tension as band released
is used up in the bend.
6. Pull cutting handle to cut the band.
When applying Giant Band clamps, prior
to cutting off clamp, release band gripper
and push tool nose away from buckle
approx. ¼”.
7. Remove tool,
holding stub of band
down with thumb.
8. Hammer
down buckle
ears to complete
BAND-IT clamp.

BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
Document # P36187 Rev. G
© Copyright
BAND-IT-IDEX, Inc. 2007
All rights reserved
www.BAND-IT-IDEX.com
Page 2 of 3
G40269 Giant II
Hand Tool
Cleaning and
Warranty
Gripper Cleaning Instructions:
1. Remove gripper. Align gripper pin
hole with notch in tool frame. Using a
punch and hammer, punch pin out of
slide block.
2. Using a wire brush, clean all
foreign matter from teeth. 3. Replace pin: Align gripper hole with slide block hole, insert pin in hole and
hammer pin in place.
Refer to website for warranty information: http://www.band-it-idex.com/warranty.html
NOTE: Periodically apply food-grade white lubricant or equivalent to tension screw thread (on
page 3) to prevent excessive wear.
If tool fails to securely grip tail of clamp, follow gripper cleaning instructions above.

BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
Document # P36187 Rev. G
© Copyright
BAND-IT-IDEX, Inc. 2007
All rights reserved
www.BAND-IT-IDEX.com
Page 3 of 3
G40269 Giant II
Hand Tool
Tool Assembly
Parts List
1. To assist in removing threaded parts,
apply heat to soften locking compound.
2. When connecting the tension screw to
the slide block, clean threads (male and
female) of foreign matter, then apply two
drops of high strength locking compound
(Loctite 271 or equiv.) onto male threads
and connect parts together. Apply 3 oz.
of white lubricant or equiv. to tension
screw thread.
3. When connecting the set screw to the
cutter bar, clean threads (male and
female) of foreign matter, then apply one
drop of medium strength locking
compound (Loctite 242 or equiv.) onto
male thread and connect parts together.
REPAIR PARTS LIST FOR G40269
PART # DESCRIPTION
G41387 TOOL FRAME
G40888 THRUST BEARING
G42487 SLIDE BLOCK ASSEMBLY
INCLUDES: SLIDE BLOCK, TENSION SCREW,
ECCENTRIC LEVER, AND LEVER PIVOT PIN
G42087 TENSION HANDLE ASSEMBLY
INCLUDES: TENSION HANDLE, SPIN GRIP AND
EXTERNAL RETAINING RING
G42287 CUTTER BAR ASSEMBLY
INCLUDES: CUTTER BAR HANDLE, CUTTER
BAR, AND SET SCREW (ON FAR SIDE)
TOOL FRAME
ECCENTRIC LEVER
PIN, ECC. LEVER PIVOT
CUTTER BAR
SET SCREW
SLIDE BLOCK
CUTTER BAR HANDLE
TENSION SCREW
THRUST
BEARING
EXTERNAL RETAINING RING SPIN GRIP
TENSION HANDLE