BDI CORRIDOR 8179-WL User manual

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today, and you will be entered to win free a BINK
table from BDI: www.bdiusa.com/register
Placement and Maintenance
Corridor®Media furniture is designed for indoor use on level floors.
Clean glass with glass cleaner, and steel parts and wood veneer with
a moist cloth.
Your Corridor®Media furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
Do not use power tools for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing
hardware pieces, please contact BDI Customer Service at
[email protected]. For all other concerns, please
contact your BDI retailer.
For your convenience, wheel assembly is pre-installed. Wheels can
be removed if desired.
bdiusa.com
customerservic[email protected]om
Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Corridor & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2016, BDI
Made in China. 06.10.2019, V11
CORRIDOR®8179
MEDIA CONSOLE
B1 Hex Wrench x 1
A Phillips Screwdriver x 1
C Cabinet x 1
D 1/4-20 x 10 mm
Machine Screw x 16
H M4 x 35 mm
Machine Screw x 8
I Door Pull x 4
K Glass Top x 1
Reinstall Leveler to Metal Leg E.
E
B2 Hex Wrench x 1
G 1/420 x 60 mm
Machine Screw x 6
E Metal Leg x 2
F Metal Rail x 2
Removal of wheels (optional):
Detach Wheel Assembly from
Metal Leg E by removing the
Leveler and Screw.
EJ Rubber Bumper x 8
N Back Panel x 2
L Adjustable Shelf x 2
M Adjustable Shelf x 1

bdiusa.com
customerservic[email protected]om
CORRIDOR 8179
MEDIA CONSOLE
2
Step 2 - Build Base Assembly
Slide Metal Leg E into Metal Rail F and attach by using Hex Wrench B1 and 8Screws D. NOTE: You
MUST align arrows on Metal Rails F with arrows on Metal Legs E for proper orientation.
Step 3 - Carefully lay Cabinet C on its back. Using Hex Wrench B1, attach the base assembly to the bottom
of the Cabinet C with Screw D and Screw G. *Note: Each of the metal legs has levelers that can be adjusted
using the Hex Wrench B2.
D x 8
G x 6
D D
DD
E E
F
F
Æ Æ
Æ Æ
D x 8

bdiusa.com
customerservic[email protected]om
CORRIDOR 8179
MEDIA CONSOLE
3
Step 4 - Position the cabinet upright and install Door Pulls I using Screw H and Screwdriver A. Adhere
Rubber Bumper J at least one (1) inch from edges of the cabinet as shown below.
Step 5 - Place Glass Top K on top of Cabinet C. Position glass flush with cabinet front doors.
H
J
JI
J
J
J
J
J
J
H
K

bdiusa.com
customerservic[email protected]om
CORRIDOR 8179
MEDIA CONSOLE
4
Step 7 - Adjustable Shelves
The shelf pins located inside all three cabinet spaces may be repositioned using Screwdriver A, allowing you to
raise or lower each Adjustable Shelf L and Adjustable Shelf M to the desired level.
Step 6 - Install both Back Panels N to the backside of the cabinet by inserting top edge in upper channel then
tipping bottom edge forward and into lower channel.
NOTE: Velcro straps are included for your convenience to facilitate wire management.
2
1
LM

bdiusa.com
customerservic[email protected]om
CORRIDOR 8179
MEDIA CONSOLE
5
Fine tuning your new BDI Corridor Home Theater Furniture
These steps are to be followed after you have unpacked and completed the simple assembly instructions for
your Corridor AV cabinet. Due to jostling in freight or perhaps an uneven floor, the doors on your Corridor cabinet
may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware
that depending on your situation, patience and a bit of trial and error are required. The high-quality European
hinge hardware is infinitely adjustable, but changing one element can cause the need for further adjustments.
Through a little adjustment, you can modify the orientation of the cabinet doors to make sure that they are sitting
perfectly on your Corridor unit.
STEP 1 - Level your Corridor unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg using Hex
Wrench (B2). If your floor is uneven, you may extend one or more levelers to attain a level, stable cabinet
placement. Turning the leveler clockwise will extend the leveler; turning it counter-clockwise will retract it.
CORRECT! Door is
sitting squarely and evenly
spaced on tops and sides.
INCORRECT! Door is
out of alignment with
the rest of the unit.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame.
If the cabinet’s doors appear out of alignment, this condition can be corrected with minor adjustment to the
European hinges on each door.
Because these hinges are infinitely adjustable, adjusting one
hinge element can sometimes cause the need for adjustments
to other elements. But with a few adjustments, you can modify
the orientation of the cabinet doors to make sure that they hang
perfectly within your cabinet.
Use the Phillips Screwdriver (A) supplied to adjust Corridor's
door hinges:
•By adjusting Screw 1, the door will move LEFT or RIGHT
within the frame. Make minor adjustments at both top and
bottom hinges for best results.
•By adjusting Screw 2 the entire door will move IN or OUT,
opening or closing the gap between the door frame and
cabinet. (This screw rarely needs adjustment.)
21
1
2