Beckhoff CP29 0000 Series User manual

Installation and Operating instructions for
CP29xx-0000
Multi-touch Control Panel with DVI/ USB Extended interface
CP29xx-0010
Multi-touch Control Panel with CP-Link 4 interface
Version: 2.1
Date: 2021-02-05

Table of contents
CP29xx 1
Table of contents
1Foreword 3
1.1 Notes on the Documentation 3
1.1.1 Liability Conditions 3
1.1.2 Trademarks 3
1.1.3 Patent Pending 3
1.1.4 Copyright 3
1.1.5 State at Delivery 3
1.1.6 Delivery conditions 3
1.2 Description of safety symbols 4
1.3 Basic safety measures 5
1.4 Operator’s obligation to exercise diligence 6
1.4.1 National regulations 6
1.4.2 Procedure in the event of a fault 6
1.4.3 Operator requirements 6
2Product Description 7
2.1 Product overview 7
2.2 Appropriate Use 9
2.3 Access to the connectors 9
2.4 Interfaces CP29xx-0000 11
2.4.1DVI-E Input (Digital Visual Interface-Extended) (X106) 11
2.4.2 USB-Extended Input (X 105) 11
2.4.3 USB in (X 104) 12
2.4.4 USB out (X 102, X 103) 12
2.4.5 Ground connection 12
2.4.6 Power Supply (X101) 12
2.5 Interfaces CP29xx-0010 13
2.5.1 CP-Link 4 Architecture Description 13
2.5.2 Interfaces 15
2.5.3 USB out (X 102, X 103) 15
2.5.4 CP-Link 4 Input (X104) 15
2.5.5 Power Supply (X101) 16
2.5.6 Ground connection 16
2.6 Connection Kits/ Connection Cables/Accessories 17
2.6.1 Connection Kits DVI-E/ USB-E connection for CP29xx-0000, optional 17
2.6.2 Accessories for CP29xx-0010, optional 17
2.6.3 Connecting cables for CP29xx-0010, optional 18
3Installation 19

Table of contents
2CP29xx
3.1 Transport and Unpacking 19
3.1.1 Transport 19
3.1.2 Unpacking 19
4Mounting 20
4.1 Installation in the control cabinet 20
4.1.1 Preparation of the control cabinet 20
4.1.2 Installation in a control cabinet wall 20
4.1.3 Earthing measures 20
4.1.4 Mounting of the Control Panel 21
4.1.5 Fitting the power supply cable 22
4.2 Connecting the Control Panel 23
4.2.1 Connecting cables 23
4.2.2 Protective Earthing 23
5Operating Instructions 24
5.1 Switching the Control Panel on and off 24
5.1.1 Switching on 24
5.1.2 Shutting down and switching off 24
5.2 Operation 24
5.3 Servicing and maintenance 25
5.3.1 Cleaning 25
5.3.2 Maintenance 25
5.4 Emergency procedures 25
5.5 Shutting down 25
5.5.1 Disposal 25
6Troubleshooting 26
7Assembly dimensions 27
8Technical Data 28
9Appendix 29
9.1 Beckhoff Support and Service 29
9.1.1 Beckhoff branches and partner companies 29
9.1.2 Beckhoff company headquarters 29
9.2 Approvals for USA and Canada 30
9.3 FCC Approvals for the United States of America 30
9.4 FCC Approval for Canada 30

Foreword
CP29xx 3
1 Foreword
1.1 Notes on the Documentation
This description is only intended for the use of trained specialists in control and automation engineering
who are familiar with the applicable national standards. It is essential that the following notes and
explanations are followed when installing and commissioning these components.
The responsible staff must ensure that the application or use of the products described satisfy all the
requirements for safety, including all the relevant laws, regulations, guidelines and standards.
1.1.1 Liability Conditions
The documentation has been prepared with care. The products described are, however, constantly under
development. For that reason the documentation is not in every case checked for consistency with
performance data, standards or other characteristics. In the event that it contains technical or editorial
errors, we retain the right to make alterations at any time and without warning. No claims for the
modification of products that have already been supplied may be made on the basis of the data, diagrams
and descriptions in this documentation.
All pictures shown in the documentation are exemplary. Illustrated configurations can differ from standard.
1.1.2 Trademarks
Beckhoff®, TwinCAT®, EtherCAT®, EtherCAT P®, Safety over EtherCAT®, TwinSAFE®, XFC®and XTS®
are registered trademarks of and licensed by Beckhoff Automation GmbH.
Other designations used in this publication may be trademarks whose use by third parties for their own
purposes could violate the rights of the owners.
1.1.3 Patent Pending
The EtherCAT Technology is covered, including but not limited to the following patent applications and
patents: EP1590927, EP1789857, DE102004044764, DE102007017835 with corresponding applications
or registrations in various other countries.
The TwinCAT Technology is covered, including but not limited to the following patent applications and
patents: EP0851348, US6167425 with corresponding applications or registrations in various other
countries.
1.1.4 Copyright
©Beckhoff Automation GmbH & Co. KG.
The reproduction, distribution and utilization of this document as well as the communication of its contents
to others without express authorization are prohibited. Offenders will be held liable for the payment of
damages. All rights reserved in the event of the grant of a patent, utility model or design.
1.1.5 State at Delivery
All the components are supplied in particular hardware and software configurations appropriate for the
application. Modifications to hardware or software configurations other than those described in the
documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.
1.1.6 Delivery conditions
In addition, the general delivery conditions of the company Beckhoff Automation GmbH & Co. KG apply.

Foreword
4CP29xx
1.2 Description of safety symbols
The following safety symbols are used in this operating manual. They are intended to alert the reader to
the associated safety instructions.
DANGER
Acute risk of injury!
If you do not adhere the safety advise adjoining this symbol, there is immediate
danger to life and health of individuals!
WARNING
Risk of injury!
If you do not adhere the safety advise adjoining this symbol, there is danger to life and
health of individuals!
CAUTION
Hazard to individuals!
If you do not adhere the safety advise adjoining this symbol, there is obvious hazard to
individuals!
Attention
Hazard to devices and environment
If you do not adhere the notice adjoining this symbol, there is obvious hazard to
materials and environment.
Note
Note or pointer
This symbol indicates information that contributes to better understanding.

Foreword
CP29xx 5
1.3 Basic safety measures
Before the Industrial PC is switched off, software that is running must be properly closed.
Otherwise it is possible that data on the storage medium is lost. Please read the section Switching the
Control Panel on and off.
Warning
Switch off all parts of the equipment, then uncouple the Control Panel
Before opening the housing, and whenever the Control Panel is not being used for
control purposes (such as during functional checks after a repair), all parts of the
equipment must first be switched off, after which the Control Panel is to be
disconnected from the equipment.
Disconnect the device by unplugging the connectors on the rear side of the Control Panel.
Items of equipment that have been switched off must be secured against being switched on again.
Warning
Do not exchange any parts when under power
When components are being fitted or removed, the supply voltage must be switched
off.
Fitting work on the Control Panel can result in damage:
•if metal objects such as screws or tools fall onto operating circuit boards
•if connecting cables internal to the Panel PC are removed or inserted during
operation.

Foreword
6CP29xx
1.4 Operator’s obligation to exercise diligence
The operator must ensure that
•the product is only used as intended (see chapter Product Description)
•the product is in a sound condition and in working order during operation
•the product is operated, maintained and repaired only by suitably qualified and authorized
personnel
•the personnel is instructed regularly about relevant occupational safety and environmental
protection aspects, and is familiar with the operating manual and in particular the safety notes
contained herein
•the operation manual is in good condition and complete, and always available for reference at the
location of the product.
Note
Do not open the housing of the Control Panel!
For technical support contact Beckhoff Service.
1.4.1 National regulations
Depending on the type of machine and plant in which the Control Panel is used, national regulations
governing the controllers of such machines will apply, and must be observed by the operator. These
regulations cover, amongst other things, the intervals between inspections of the controller. The operator
must initiate such inspections in good time.
1.4.2 Procedure in the event of a fault
In the event of faults at the Control Panel, the list in the section Troubleshooting can be used to determine
the measures to be taken.
1.4.3 Operator requirements
Anyone who uses the Control Panel must have read these operating instructions and must be familiar
with all the functions of the software installed on the Industrial PC to which he has access.

Product Description
CP29xx 7
2 Product Description
2.1 Product overview
Front view of CP29xx
The new Beckhoff panel generation with industry-standard multi-touch display offers a feature-laden
solution for any application. The wide selection of models offers different display sizes and formats as
well as custom designs. Even for single-touch users, this new panel generation offers an excellent price-
to-performance ratio and represents an economical alternative to other systems.
The multi-touch built-in Control Panel offer the following benefits:
•display sizes from 7-inch to 24-inch (16:9, 5:4, 4:3), landscape and portrait orientation
•multi-touch (PCT): e.g. for 5-finger or 2-hand touch operation
•high touch-point density for safe operation
•aluminium housing with glass front, front side IP65, rear side IP20, the housing surface is
electrically insulating
•CP29xx-0000 with integrated DVI/USB extension technology:
–DVI-E and USB-E 2.0 enable remote panel operation at a distance of up to 50 m from the PC
–USB-E 2.0 transmits USB 2.0 with 480 Mbit/s
–DVI-E input is compatible to the standard DVI output of a PC
•CP29xx-0010 with CP-Link 4 technology:
–enables remote panel operation at a distance of up to 100 m from the PC via a CAT.6A cable
–integrated or separate 24 V DC power supply
–CP-Link 4 transmits USB 2.0 with 100 MBit/s
•2-port USB socket inside the Control Panel backplane
•optional electromechanical push-button extension.

Product Description
8CP29xx

Product Description
CP29xx 9
2.2 Appropriate Use
The multi-touch built-in Control Panel CP29xx is designed for industrial application in machine and plant
engineering. A multi-touch display is accommodated in a stainless steel housing. The Control Panel is
installed in the front of control cabinets.
The DVI/USB extension technology integrated in the CP29xx-0000 Control Panel enables remote Panel
operation at a distance of up to 50 m from the PC via a standard cable.
The CP-Link 4 connection technology integrated in the CP29xx-0010 Control Panel enables remote panel
operation at a distance of up to 100 m from the PC via a CAT.6Acable with integrated or separate
24 V DC power supply depending on the transmitter module.
Danger
Risk of explosion!
The Control Panel must not be used where there is a risk of explosion.
2.3 Access to the connectors
The connectors of the Control Panel are located at the rear side of the housing.
Connection block CP29xx-0000
For the pin assignment see chapter Interfaces CP29xx-0000.

Product Description
10 CP29xx
Connection block CP29xx-0010
For the pin assignment see chapter Interfaces CP29xx-0010.

Product Description
CP29xx 11
2.4 Interfaces CP29xx-0000
2.4.1 DVI-E Input (Digital Visual Interface-Extended) (X106)
X106
DVI-D 3 X 8-pole digital PCB installation (MOLEX 74320-9000 / 74320-9004)
The DVI-E connection (X 106) is used for transferring the video signal from the Industrial PC to the
Control Panel.
The graphics signal is transferred directly via a DVI cable over a distance of 50 m max. Such a cable
length leads to strong distortion of the graphics signal on arrival at the Control Panel. The CP29xx Control
Panel features a signal processor that restores the DVI signal. The PC requires a conventional DVI
output.
Pin
Signal
Pin
Signal
1
Rx2-
13
Rx3+
2
Rx2-
14
+ 5V DVI
3
GND
15
GND
4
Rx4-
16
HPD
5
Rx4+
17
Rx0-
6
DDC CLK
18
Rx0+
7
DDC DAT
19
GND
8
AV SYNC
20
Rx5-
9
Rx1-
21
Rx5+
10
Rx1+
22
GND
11
GND
23
RxC+
12
Rx3-
24
RxC-
2.4.2 USB-Extended Input (X 105)
X105
Connection via standard-RJ45-cabel, not crossed
The Control Panel is connected with the CU8801 USB to USB extended converter box via the USB-
Extended input (X 105).
In order to realize a distance of 50 m without hubs, with USB extended the USB signal is converted so
that it can be transferred via 50 m CAT5 cables commonly used for Ethernet wiring. In the Control Panel
the signal is converted back to USB.
X106
DVI-E Input
X105
USB-E
Input
X101
Power
Ground
X104
USB in
X102,
X103
USB out

Product Description
12 CP29xx
2.4.3 USB in (X 104)
X104
USB type B, PCB installation (FCI 61729-0010B USB Receptacle B-Type)
The Control Panel is connected with the Industrial PC via the USB port (X 104, connector type B).
USB3.0 standard is supported.
Pin
Signal
Pin
Signal
1
5V
3
D+
2
D-
4
GND
2.4.4 USB out (X 102, X 103)
X102, X103
USB Type-A twin circuit board mounting (FCI 72309-0030B USB Double Receptacle A-Type)
The two USB interfaces (X102, X103,connector type A) are used for connecting peripheral devices with
USB connection. USB3.0 standard is supported in a distance of up to 3 m from the PC, from a distance of
3 m up to 50 m or if using USB-Extended, USB2.0 standard is supported.
Pin
Signal
Pin
Signal
1
5V
3
D+
2
D-
4
GND
2.4.5 Ground connection
The Control Panel is grounded via the screw connection (Ground).
Note
Malfunction possible with missing ground connection
A proper ground connection of the device is absolutely necessary for the correct
function of the touchscreen.
2.4.6 Power Supply (X101)
X101
Socket 5-pol RM3.50 Sw Screw Clamp BL3.5/180F (WEIDMÜLLER 1615810000)
The power supply for the Control Panel is established via the socket (X101). The power supply connector
is included in delivery.
Pin
Signal
Pin
Signal
1
NC
4
GND
Power Supply
2
NC
5
+ 24 VDC
3

Product Description
CP29xx 13
2.5 Interfaces CP29xx-0010
2.5.1 CP-Link 4 Architecture Description
2.5.1.1 CP-Link 4 –The Two Cable Display Link
The CP29xx-0010 multi-touch panels can be operated up to 100 m away from the PC. CP-Link 4
transfers DVI and USB together via a CAT.6Acable. The CU8802 CP-Link 4 transmitter box is connected
to the PC via DVI and USB, or else the C9900-E276 PCIe module for CP-Link 4 is installed in the PC.
CP-Link 4 –The Two Cable Display Link via the CU8802 transmitter box
CP-Link 4 –The Two Cable Display Link via the C9900-E276 PCIe module

Product Description
14 CP29xx
2.5.1.2 CP-Link 4 –The One Cable Display Link
The power supply for the Control Panel can also be provided via CP-Link 4. The CU8803 CP-Link 4
transmitter box is used instead of the CU8802 or the PCIe module. The Control Panel remains
unchanged. The CU8803 sender box provides power to the Control Panel via the CAT.6Acable, which
also transfers DVI and USB. The power supply socket of the panel is not used.
Attention
Don’t connect power supply socket if using One Cable technology
If using the CP-Link 4 - One Cable Display Link technology, do not connect anything to
the power supply socket of the Panel.
CP-Link 4 –The One Cable Display Link via the CU8803 transmitter box

Product Description
CP29xx 15
2.5.2 Interfaces
2.5.3 USB out (X 102, X 103)
X102, X103
USB Type-A twin circuit board mounting (FCI 72309-0030B USB Double Receptacle A-Type)
The two USB interfaces (X102, X103,connector type A) are used for connecting peripheral devices with
USB connection. USB2.0 standard is supported.
Pin
Signal
Pin
Signal
1
5V
3
D+
2
D-
4
GND
2.5.4 CP-Link 4 Input (X104)
X104
BA 1x8pole RJ45 Invers shield 2XLWL Lp-mount. Molex Nr: 43860-0016 Modular Jack
The Control Panel is connected with the PCIe module slot of the Industrial PC or the transmitter box
CU8802/ CU8803 via the CP-Link 4 Input (X 104).
Pin
Signal
Pin
Signal
1
CP-Link4_0P
5
CP-Link4_2N
2
CP-Link4_0N
6
CP-Link4_1N
3
CP-Link4_1P
7
CP-Link4_3P
4
CP-Link4_2P
8
CP-Link4_3N
Attention
CU8803-0000 disconnect power supply
If using the CP-Link 4 - One Cable Display Link, the 24 V power supply of the CP-Link 4
transmitter box must be switched off before disconnecting the CP-Link 4 output
connection.
X102,
X103
USB out
X101
Power
Ground
X104
CP-Link 4
Input

Product Description
16 CP29xx
Note
CP-Link 4 cables with above 60 m cable-length with ferrite core
CP-Link 4 cables with above 60 m cable-length are fitted with a ferrite core at one end.
If connecting the cable make sure to plug in the cable as shown in the picture with the
ferrite core Control Panel-sided.
CP-Link 4 cable connection
2.5.5 Power Supply (X101)
X101
Socket 5-pol RM3.50 Sw Screw Clamp BL3.5/180F (WEIDMÜLLER 1615810000)
The optional power supply for the Control Panel is established via the socket (X101), see chapter
CP-Link 4 Architecture Description. The power supply connector is included in delivery.
Pin
Signal
Pin
Signal
1
NC
4
GND
Power Supply
2
NC
5
+ 24 VDC
3
Attention
Don’t connect power supply socket if using One Cable technology
If using the CP-Link 4 - One Cable Display Link technology, do not connect anything to
the power supply socket of the Panel.
2.5.6 Ground connection
The Control Panel is grounded via the screw connection (Ground).
Note
Malfunction possible with missing ground connection
A proper ground connection of the device is absolutely necessary for the correct
function of the touchscreen.
ferrite core

Product Description
CP29xx 17
2.6 Connection Kits/ Connection Cables/Accessories
One 5-pole power supply connector is provided with the Control Panel.
Optionally prefabricated connection kits for the DVI-E/ USB-E connection are available.
2.6.1 Connection Kits DVI-E/ USB-E connection for CP29xx-0000, optional
The following connection kits are available:
Connecting kit
DVI-E/ USB-E Connection
C9900-K622
Connecting kit 1 m for CP29xx, containing:
1 m DVI cable, 1 m USB cable
C9900-K623
Connecting kit 3 m for CP29xx, containing:
3 m DVI cable, 3 m USB cable
C9900-K624
Connecting kit 5 m for CP29xx, containing:
5 m DVI cable, 5 m USB cable
C9900-K625
Connecting kit 10 m for CP29xx, containing:
10 m DVI cable, 10 m CAT 5 cable for USB-E-2.0, USB to USB-E-2.0 converter
CU8801 for mounting rail installation close to the PC and 1 m USB cable to connect
the USB to USB-E-2.0 converter to the PC
C9900-K626
Connecting kit 20 m for CP29xx, containing:
20 m DVI cable, 20 m CAT 5 cable for USB-E-2.0, USB to USB-E-2.0 converter
CU8801 for mounting rail installation close to the PC and 1 m USB cable to connect
the USB to USB-E-2.0 converter to the PC
C9900-K627
Connecting kit 30 m for CP29xx, containing:
30 m DVI cable, 30 m CAT 5 cable for USB-E-2.0, USB to USB-E-2.0 converter
CU8801 for mounting rail installation close to the PC and 1 m USB cable to connect
the USB to USB-E-2.0 converter to the PC
C9900-K628
Connecting kit 40 m for CP29xx, containing:
40 m DVI cable, 40 m CAT 5 cable for USB-E-2.0, USB to USB-E-2.0 converter
CU8801 for mounting rail installation close to the PC and 1 m USB cable to connect
the USB to USB-E-2.0 converter to the PC
C9900-K629
Connecting kit 50 m for CP29xx, containing:
50 m DVI cable, 50 m CAT 5 cable for USB-E-2.0, USB to USB-E-2.0 converter
CU8801 for mounting rail installation close to the PC and 1 m USB cable to connect
the USB to USB-E-2.0 converter to the PC
2.6.2 Accessories for CP29xx-0010, optional
The following accessories are available:
Accessories
for CP-Link 4
CU8802-0000
Transmitter box for CP-Link 4 –The Two Cable Display Link
CP-Link 4 Extender Tx for connecting a Control Panel with CP-Link 4 interface CP29xx-0010 or
CP39xx-0010
CU8803-0000
Transmitter box for CP-Link 4 –The One Cable Display Link
CP-Link 4 Extender Tx for connecting a Control Panel with CP-Link 4 interface CP29xx-0010 or
CP39xx-0010
C9900-E276
PCIe module for CP-Link 4 –The Two Cable Display Link
CP-Link 4 Extender Tx PCIe module

Product Description
18 CP29xx
2.6.3 Connecting cables for CP29xx-0010, optional
The following connection cables are available:
Accessories
Cable for CU880x
C9900-K671
Connecting cable RJ45 CAT.6A, 3 m
C9900-K672
Connecting cable RJ45 CAT.6A, 5 m
C9900-K673
Connecting cable RJ45 CAT.6A, 10 m
C9900-K674
Connecting cable RJ45 CAT.6A, 20 m
C9900-K675
Connecting cable RJ45 CAT.6A, 30 m
C9900-K676
Connecting cable RJ45 CAT.6A, 40 m
C9900-K677
Connecting cable RJ45 CAT.6A, 50 m
C9900-K678
Connecting cable RJ45 CAT.6A, 60 m
C9900-K679
Connecting cable RJ45 CAT.6A, 70 m
C9900-K680
Connecting cable RJ45 CAT.6A, 80 m
C9900-K681
Connecting cable RJ45 CAT.6A, 90 m
C9900-K682
Connecting cable RJ45 CAT.6A, 100 m
C9900-K725
Connecting cable RJ45 CAT.6A, 3 m, suitable as trailing cable
C9900-K713
Connecting cable RJ45 CAT.6A, 5 m, suitable as trailing cable
C9900-K714
Connecting cable RJ45 CAT.6A, 10 m, suitable as trailing cable
C9900-K715
Connecting cable RJ45 CAT.6A, 20 m, suitable as trailing cable
C9900-K716
Connecting cable RJ45 CAT.6A, 30 m, suitable as trailing cable
C9900-K717
Connecting cable RJ45 CAT.6A, 40 m, suitable as trailing cable
C9900-K718
Connecting cable RJ45 CAT.6A, 50 m, suitable as trailing cable
C9900-K719
Connecting cable RJ45 CAT.6A, 60 m, suitable as trailing cable
C9900-K720
Connecting cable RJ45 CAT.6A, 70 m, suitable as trailing cable
C9900-K721
Connecting cable RJ45 CAT.6A, 80 m, suitable as trailing cable