Beckhoff Cp2912 User manual

Installation and Operating instructions for

CP29xx

Multi-touch built-in Control Panel with

DVI/ USB Extended interface

Version: 1.4

Date: 2013-12-19

Table of contents

1Foreword 3

1.1 Notes on the Documentation 3

1.1.1 Liability Conditions 3

1.1.2 Trademarks 3

1.1.3 Patent Pending 3

1.1.4 Copyright 3

1.1.5 State at Delivery 3

1.1.6 Delivery conditions 3

1.2 Description of safety symbols 4

1.3 Basic safety measures 5

1.4 Operator’s obligation to exercise diligence 6

1.4.1 National regulations 6

1.4.2 Procedure in the event of a fault 6

1.4.3 Operator requirements 6

2Product Description 7

2.1 Product overview 7

2.2 Appropriate Use 8

2.3 Access to the connectors 8

2.4 Interfaces 9

2.4.1 DVI-E Input (Digital Visual Interface-Extended) (X106) 9

2.4.2 USB-Extended Input (X 105) 10

2.4.3 USB in (X 104) 10

2.4.4 USB out (X 102, X 103) 10

2.4.5 Ground connection 10

2.4.6 Power Supply (X101) 10

2.5 Connection Kits/ Connection Cables 11

2.5.1 Connection Kits for DVI-E/ USB-E connection, optional 11

3Installation 12

3.1 Transport and Unpacking 12

3.1.1 Transport 12

3.1.2 Unpacking 12

4Mounting 13

4.1 Installation in the control cabinet 13

4.1.1 Preparation of the control cabinet 13

4.1.2 Installation in a control cabinet wall 13

4.1.3 Earthing measures 13

CP29xx 1

Table of contents

4.1.4 Mounting of the Control Panel 14

4.1.5 Fitting the power supply cable 15

4.2 Connecting the Control Panel 16

4.2.1 Connecting cables 16

4.2.2 Protective Earthing 16

5Operating Instructions 17

5.1 Switching the Control Panel on and off 17

5.1.1 Switching on 17

5.1.2 Shutting down and switching off 17

5.2 Operation 17

5.2.1 Setting the transmission rate 17

5.3 Servicing and maintenance 18

5.3.1 Cleaning 18

5.3.2 Maintenance 18

5.4 Emergency procedures 18

5.5 Shutting down 18

5.5.1 Disposal 18

6Troubleshooting 19

7Assembly dimensions 20

8Technical Data 29

9Appendix 30

9.1 Beckhoff Support and Service 30

9.1.1 Beckhoff branches and partner companies 30

9.1.2 Beckhoff company headquarters 30

9.2 Approvals for USA and Canada 31

9.3 FCC Approvals for the United States of America 31

9.4 FCC Approval for Canada 31

2CP29xx

Foreword

1 Foreword

1.1 Notes on the Documentation

This description is only intended for the use of trained specialists in control and automation engineering

who are familiar with the applicable national standards. It is essential that the following notes and

explanations are followed when installing and commissioning these components.

The responsible staff must ensure that the application or use of the products described satisfy all the

requirements for safety, including all the relevant laws, regulations, guidelines and standards.

1.1.1 Liability Conditions

The documentation has been prepared with care. The products described are, however, constantly under

development. For that reason the documentation is not in every case checked for consistency with

performance data, standards or other characteristics. In the event that it contains technical or editorial

errors, we retain the right to make alterations at any time and without warning. No claims for the

modification of products that have already been supplied may be made on the basis of the data, diagrams

and descriptions in this documentation.

1.1.2 Trademarks

Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®and XFC®are registered

trademarks of and licensed by Beckhoff Automation GmbH.

Other designations used in this publication may be trademarks whose use by third parties for their own

purposes could violate the rights of the owners.

1.1.3 Patent Pending

The EtherCAT Technology is covered, including but not limited to the following patent applications and

patents: EP1590927, EP1789857, DE102004044764, DE102007017835 with corresponding applications

or registrations in various other countries.

The TwinCAT Technology is covered, including but not limited to the following patent applications and

patents: EP0851348, US6167425 with corresponding applications or registrations in various other

countries.

1.1.4 Copyright

©Beckhoff Automation GmbH.

The reproduction, distribution and utilization of this document as well as the communication of its contents

to others without express authorization are prohibited. Offenders will be held liable for the payment of

1.1.5 State at Delivery

All the components are supplied in particular hardware and software configurations appropriate for the

application. Modifications to hardware or software configurations other than those described in the

documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH.

1.1.6 Delivery conditions

In addition, the general delivery conditions of the company Beckhoff Automation GmbH apply.

CP29xx 3

Foreword

1.2 Description of safety symbols

The following safety symbols are used in this operating manual. They are intended to alert the reader to

the associated safety instructions.

Acute risk of injury!

DANGER

If you do not adhere the safety advise adjoining this symbol, there is immediate

danger to life and health of individuals!

Risk of injury!

WARNING

If you do not adhere the safety advise adjoining this symbol, there is danger to life and

health of individuals!

Hazard to individuals!

CAUTION

If you do not adhere the safety advise adjoining this symbol, there is obvious hazard to

individuals!

Hazard to devices and environment

Attention

If you do not adhere the notice adjoining this symbol, there is obvious hazard to

materials and environment.

Note or pointer

Note

This symbol indicates information that contributes to better understanding.

4CP29xx

Foreword

1.3 Basic safety measures

Before the Industrial PC is switched off, software that is running must be properly closed.

Otherwise it is possible that data on the storage medium is lost. Please read the section Switching the

Control Panel on and off.

Switch off all parts of the equipment, then uncouple the Control Panel

Warning

Before opening the housing, and whenever the Control Panel is not being used for

control purposes (such as during functional checks after a repair), all parts of the

equipment must first be switched off, after which the Control Panel is to be

disconnected from the equipment.

Disconnect the device by unplugging the connectors on the rear side of the Control Panel.

Items of equipment that have been switched off must be secured against being switched on again.

Do not exchange any parts when under power

Warning

When components are being fitted or removed, the supply voltage must be switched

off.

Fitting work on the Control Panel can result in damage:

• if metal objects such as screws or tools fall onto operating circuit boards

• if connecting cables internal to the Panel PC are removed or inserted during

operation.

CP29xx 5

Foreword

1.4 Operator’s obligation to exercise diligence

The operator must ensure that

• the product is only used as intended (see chapter Product Description)

• the product is in a sound condition and in working order during operation

• the product is operated, maintained and repaired only by suitably qualified and authorized

personnel

• the personnel is instructed regularly about relevant occupational safety and environmental

protection aspects, and is familiar with the operating manual and in particular the safety notes

contained herein

• the operation manual is in good condition and complete, and always available for reference at the

location of the product.

Do not open the housing of the Control Panel!

Note

For technical support contact Beckhoff Service.

1.4.1 National regulations

Depending on the type of machine and plant in which the Control Panel is used, national regulations

governing the controllers of such machines will apply, and must be observed by the operator. These

regulations cover, amongst other things, the intervals between inspections of the controller. The operator

must initiate such inspections in good time.

1.4.2 Procedure in the event of a fault

In the event of faults at the Control Panel, the list in the section Troubleshooting can be used to determine

the measures to be taken.

1.4.3 Operator requirements

Anyone who uses the Control Panel must have read these operating instructions and must be familiar

with all the functions of the software installed on the Industrial PC to which he has access.

6CP29xx

Product Description

2 Product Description

2.1 Product overview

Front view of CP29xx

The new Beckhoff panel generation with industry-standard multi-touch display offers a feature-laden

solution for any application. The wide selection of models offers different display sizes and formats as

well as custom designs. Even for single-touch users, this new panel generation offers an excellent price-

to-performance ratio and represents an economical alternative to other systems.

The multi-touch built-in Control Panel offer the following benefits:

• display sizes from 7-inch to 24-inch (16:9, 5:4, 4:3), landscape and portrait orientation

• multi-touch (PCT): e.g. for 5-finger or 2-hand touch operation

• high touch-point density for safe operation

• aluminium housing with glass front, front side IP65, rear side IP20

• integrated DVI/USB extension technology:

– DVI-E and USB-E 2.0 enable remote panel operation at a distance of up to 50 m from the PC

– USB-E 2.0 transmits USB 2.0 with 480 Mbit/s

– DVI-E input is compatible to the standard DVI output of a PC

• USB 3.0 input for the direct connection to a standard USB output of a PC with distances of up to

3 m

• 2-port USB 3.0 socket inside the Control Panel backplane, for USB-E 2.0 limited to USB 2.0

• optional electromechanical push-button extension.

CP29xx 7

Product Description

2.2 Appropriate Use

The multi-touch built-in Control Panel CP29xx is designed for industrial application in machine and plant

engineering. A multi-touch display is accommodated in a stainless steel housing. The Control Panel is

installed in the front of control cabinets.

The DVI/USB extension technology integrated in the CP29xx Control Panel enables remote Panel

operation at a distance of up to 50 m from the PC via a standard cable.

Risk of explosion!

Danger

The Control Panel must not be used where there is a risk of explosion.

2.3 Access to the connectors

The connectors of the Control Panel are located at the rear side of the housing.

Picture: Bottom view

8CP29xx

Product Description

2.4 Interfaces

X104

USB in

X102,

X103

USB out

Ground X101

Power

X106

DVI-E Input

X105

USB-E

Input

2.4.1 DVI-E Input (Digital Visual Interface-Extended) (X106)

X106

DVI-D 3 X 8-pole digital PCB installation (MOLEX 74320-9000 / 74320-9004)

The DVI-E connection (X 106) is used for transferring the video signal from the Industrial PC to the

Control Panel.

The graphics signal is transferred directly via a DVI cable over a distance of 50 m max. Such a cable

length leads to strong distortion of the graphics signal on arrival at the Control Panel. The CP29xx Control

Panel features a signal processor that restores the DVI signal. The PC requires a conventional DVI

output.

The transmission rate of the DDC file has to be limited

Note At large distance between PC and Control Panel, the transmission rate of the DDC file

has to be limited.

See also chapter Setting the transmission rate.

Pin Signal Pin Signal

1 Rx2- 13 Rx3+

2 Rx2- 14 + 5V DVI

3 GND 15 GND

4 Rx4- 16 HPD

5 Rx4+ 17 Rx0-

6 DDC CLK 18 Rx0+

7 DDC DAT 19 GND

8 AV SYNC 20 Rx5-

9 Rx1- 21 Rx5+

10 Rx1+ 22 GND

11 GND 23 RxC+

12 Rx3- 24 RxC-

CP29xx 9

Product Description

2.4.2 USB-Extended Input (X 105)

X105

Connection via standard-RJ45-cabel, not crossed

The Control Panel is connected with the CU8801 USB to USB extended converter box via the USB-

Extended input (X 105).

In order to realize a distance of 50 m without hubs, with USB extended the USB signal is converted so

that it can be transferred via 50 m CAT5 cables commonly used for Ethernet wiring. In the Control Panel

the signal is converted back to USB.

2.4.3 USB in (X 104)

X104

USB type B, PCB installation (FCI 61729-0010B USB Receptacle B-Type)

The Control Panel is connected with the Industrial PC via the USB port (X 104, connector type B).

USB3.0 standard is supported.

Pin Signal Pin Signal

1 5V 3 D+

2 D- 4 GND

2.4.4 USB out (X 102, X 103)

X102, X103

USB Type-A twin circuit board mounting (FCI 72309-0030B USB Double Receptacle A-Type)

The two USB interfaces (X102, X103,connector type A) are used for connecting peripheral devices with

USB connection. USB3.0 standard is supported in a distance of up to 5 m from the PC, from a distance of

5 m up to 50 m USB2.0 standard is supported.

Pin Signal Pin Signal

1 5V 3 D+

2 D- 4 GND

2.4.5 Ground connection

The Control Panel is grounded via the screw connection (Ground).

2.4.6 Power Supply (X101)

X101

Socket 5-pol RM3.50 Sw Screw Clamp BL3.5/180F (WEIDMÜLLER 1615810000)

The power supply for the Control Panel is established via the socket (X101). The power supply connector

is included in delivery.

Pin Signal Pin Signal

1 NC 4 GND

2 NC 5 + 24 VDC Power Supply

10 CP29xx

Product Description

2.5 Connection Kits/ Connection Cables

One 5-pole power supply connector is provided with the Control Panel.

Optionally prefabricated connection kits for the DVI-E/ USB-E connection are available.

2.5.1 Connection Kits for DVI-E/ USB-E connection, optional

The following connection kits are available:

Connecting kit DVI-E/ USB-E Connection

C9900-K622 Connecting kit 1 m for CP29xx, containing:

1 m DVI cable, 1 m USB cable

C9900-K623 Connecting kit 3 m for CP29xx, containing:

3 m DVI cable, 3 m USB cable

C9900-K624 Connecting kit 5 m for CP29xx, containing:

5 m DVI cable, 5 m USB cable

C9900-K625 Connecting kit 10 m for CP29xx, containing:

10 m DVI cable, 10 m CAT 5 cable for USB-E-2.0, USB to USB-E-2.0 converter