Belden Hirschmann RS20 Series User manual

Installation RS20/22/30/32/40
Release 04 02/2015
Technical Support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Rail Switch
RS20/RS22/RS30/RS32/RS40 Family
RS30-0802...
RS30
RM
+24V(P1) 0V 0V
FAULT
+24V(P2)
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
3
5
7
9
4
6
8
10
V.24
USB
P
Stand by
FAULT
RM
ON
LS
2
DA
LS
1
DA
RS30-1602...
RS20
+24V(P1) 0V 0V
FAULT
+24V(P2)
4
6
8
5
7
9
LS DA
2
LS DA
1
LS DA
3
RS30
+24V(P1) 0V 0V
FAULT
+24V(P2)
5
7
9
11
6
8
10
12
13
15
17
14
16
18
LS DA
1
LS DA
2
LS DA
3
LS DA
4
RS20
LS DA
RM
+24V(P1) 0V 0V
FAULT
+24V(P2)
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
3
5
7
9
11
13
15
17
2
LS DA
1
4
6
8
10
12
14
16
18
19
21
23
20
22
24
V.24
USB
P
Stand by
FAULT
RM
ON
RS20
LS DA
RM
+24V(P1) 0V 0V
FAULT
+24V(P2)
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
2
LS DA
1
3
5
7
4
6
8
V.24
USB
P
Stand by
FAULT
RM
ON
RS20
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
LS
1
DA
LS
2
DA
LS
3
DA
LS
4
DA
RS20-0800...RS20-2400... RS20-0400...
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
RS20-0900...
RS40
+24V(P1) 0V 0V
FAULT
+24V(P2)
1
3
5
7
2
4
6
8
1
2
3
4
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
9
RS40-0009... RS32-0802... RPS90/48V HV
RPS90/48V HV
U: 110 / 230 VAC
U: 60 / 250 VDC
-/N
+/L
0V
+48V / 1,9A
48-54V
P
RS32
1
GB
2
GB
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
LS DA
LS DA
3
5
7
9
4
6
8
10
+24V(P1) 0V 0V
FAULT
+24V(P2)
FAULT
+48V(P1) 0V 0V +48V(P2)

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2015 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. The end user license on the provided CD/DVD is effective for devices with
embedded software.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This publication was created by Hirschmann Automation and
Control GmbH to the best of its knowledge. Hirschmann reserves the right to change the content
of this publication at any time without notice. Hirschmann does not give any warranty or
assurance with respect to the correctness or accuracy of the details in this publication.
Hirschmann accepts no liability for damage in any way related to the use of the network
components or their operating system software. In addition, we refer to the conditions of use
specified in the license contract.
You will the latest version of this manual on the internet at Hirschmann product pages
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
RS20/22/30/32/40 039 692-003-04-0215 –15.04.2015

Installation RS20/22/30/32/40
Release 04 02/2015 3
Content
Safety Information 5
About this manual 16
Key 16
1 Description 17
1.1 Description of the device variants 18
1.1.1 Combination options of the device variants
RS20/RS30/RS22/RS32 19
1.1.2 Combination options for the RS40 device variants 22
1.1.3 Number of ports and media for RS20-... 24
1.1.4 Number of ports and media for RS30-... 27
1.1.5 Number of ports and media for RS40-... 30
1.2 Device variants with PoE (optional) 31
1.2.1 Number of ports and media for devices with PoE 31
1.2.2 PoE power units 33
1.3 Ethernet ports 33
1.3.1 10/100/1000 Mbit/s twisted pair port 33
1.3.2 10/100 Mbit/s twisted pair port 34
1.3.3 10/100 Mbit/s twisted-pair connection PoE
(RS22-.../RS32-...) 34
1.3.4 1000-Mbit/s F/O port 35
1.3.5 100 Mbit/s F/O port 36
1.3.6 Gigabit combo port 36
1.4 Display elements 37
1.5 Management interfaces 38
1.5.1 USB interface 38
1.5.2 V.24 interface (external management) 39
2 Installation 40
2.1 Checking the package contents 40
2.2 Installing and grounding the device 40
2.2.1 Snapping a unit onto the DIN rail 41
2.2.2 DIN rail mounting on ships (RS30-0802...) 42
2.2.3 Mounting on a vertical flat surface 43
2.2.4 Grounding 43
2.3 Installing an SFP transceiver (optional) 44
2.4 Adjust DIP switch settings 44

4Installation RS20/22/30/32/40
Release 04 02/2015
2.5 Wiring the terminal blocks 45
2.5.1 RS20/RS30/RS40 supply voltage and Signal contact 45
2.5.2 RS22/RS32: Supply voltage and signal contact 46
2.6 Mounting a terminal block 50
2.7 Connecting the ferrite 50
2.8 Operating the device 50
2.9 Connecting data cables 51
2.10 Insert data in label area 51
3 Making basic settings 52
4 Monitoring the ambient air temperature 53
5 Maintenance and service 54
6Disassembly 55
6.1 Removing the device 55
6.2 Removing an SFP transceiver (optional) 56
7 Technical Data 57
A Further support 71

Installation RS20/22/30/32/40
Release 04 02/2015 5
Safety Information
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Intended usage
Use the device only for the application cases described in the Hirschmann
product information, including this manual.
Operate the device only according to the technical specifications.
See “Technical Data” on page 57.
Installation site requirements
Install the device in a fire enclosure according to EN 60950-1.
If installed in a living area or office environment, the device must be
operated only in switch cabinets with fire protection characteristics
according to EN 60950-1.
Only when using the PoE power supply unit RPS90/48V HV:
Install the device at ambient temperatures greater than 113 °F (45 °C)
in “restricted access locations” based on EN 60950-1 exclusively.
Install this device only in a switch cabinet or in a restricted access
location, to which maintenance staff have exclusive access.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation RS20/22/30/32/40
Release 04 02/2015
Device casing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
See “General technical data” on page 57.
Install the device in the vertical position.
At ambient temperatures > 60 °C:
The surfaces of the device casing may become hot. Avoid touching the
device while it is operating.
Qualification requirements for personnel
Allow qualified personnel exclusively to perform any work on the
device.
Qualified personnel are characterized by the following points:
The qualified personnel has received an appropriate training. Proper
training as well as a practical knowledge and experience constitute the
qualification. This qualification is the requirement to connect, to ground
and to label power circuits, devices, and systems in accordance with
current safety engineering standards.
The qualified personnel are aware of the hazards associated with their
tasks.
The qualified personnel know proper measures against such hazards
to minimize the risk for themselves and others.
The qualified personnel participate in regular training.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Grounding
The housing is grounded via the separate ground screw on the bottom left
of the front panel.
Use a wire diameter of at least 1.0 mm² for the ground conductor.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
Shielding ground
The overall shield of a connected shielded twisted pair cable is connected
to the ground connector on the front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.

Installation RS20/22/30/32/40
Release 04 02/2015 7
Supply voltage
The supply voltage is electrically isolated from the housing.
The devices are designed for operation with safety extra-low voltage.
Connect only safety extra-low voltage circuits with voltage restrictions
in line with IEC/EN 60950-1 to the supply voltage connections and
signal contacts.
Connect only a supply voltage that corresponds to the type plate of
your device.
Observe the maximum values for contact load of the signal contact.
Applies to North America:
The device must only be connected to a Class 2 supply voltage that
meets the requirements of the National Electrical Code, Table 11(b). If
the voltage is being supplied redundantly (two different voltage
sources), the combined supply voltages must fulfill the requirements of
the National Electrical Code, Table 11(b).
Applies to North America: For use with Class 2 circuits only.
Use only copper wire (Cu) 60/75 °C or 75 °C.
Applies to North America:
For modules certified for hazardous locations: make sure that
peripheral devices are suitable for the application environment. The
wiring for the voltage supply and for the inputs and outputs (I/O) must
adhere to the wiring regulations for Class I, Division 2 [article 501(b) of
the National Electrical Code (USA), NFPA 70] and to the applicable
statutory regulations.
Start connecting the electrical wires only if all the above safety
requirements are fulfilled.
Enable the supply voltage for the device only when the following
requirements are fulfilled:
the housing is closed
the terminal blocks are wired correctly
the terminal blocks for the power supply are connected
Internal fuses are triggered only in the case of a detected error in the
device. In case of damage or malfunction of the device, turn off the
supply voltage and return the device to the plant for inspection.

8Installation RS20/22/30/32/40
Release 04 02/2015
Supply voltage for PoE power supply units (optional)
Connect the protective conductor with the ground screw before you set
up the other connections. When removing the cables, remove the
protective conductor last.
Make sure that the cross-section of the protective conductor cable is
the same size as or bigger than the cross-section of the voltage supply
cables.
Only use connection cables that are permitted for the specified
temperature range.
Connect only a supply voltage that corresponds to the type plate of
your device.
PoE power supply unit RPS90/48V LV:18 V DC to 60 V DC
PoE power supply unit RPS90/48V HV:48 V DC to 320 V DC or 90
V AC to 265 V AC
Install a suitable input fuse in the following cases:
The neutral conductor or the negative terminal of the supply voltage
is ungrounded.
For the supply voltage, you provide a DC voltage greater than
125 V DC.
See “General technical data” on page 57.
With AC power supply, use a cable cross-section of at least 0.75 mm²
(for North America AWG 18) for the current conductor at the voltage
input.
With DC power supply, use a cable cross-section of at least 1.0 mm²
(for North America AWG 16) for the current conductor at the voltage
input.

Installation RS20/22/30/32/40
Release 04 02/2015 9
ATEX directive 94/9/EC – specific regulations for safe
operation
Relevant for RS20/22/30/32/40 devices when operating in explosive gas
atmospheres according to ATEX Directive 94/9 EC, the following applies:
List of standards:
EN 60079-0:2009
EN 60079-15:2010
Certificate No.: DEKRA 11ATEX0139 X or KEMA 09ATEX0067 X.
Make sure that the device has the following label:
II 3G Ex nA IIC T4 Gc DEKRA 11ATEX0139 X
for RS20/22/30/32 types.
II 3G Ex nA IIC T3 ... T4 Gc KEMA 09ATEX0067 X
for RS40 types.
Environmental class and temperature code for types RS20 and RS30:
T4: 0 °C ≤Ta ≤+60 °C for "S" types
(Item 14 in the schematic legend) or
T4: −40 °C ≤Ta ≤+70 °C for "T" or "E" types
(Item 14 in the schematic legend).
Environmental class and temperature code for types RS22 and RS32:
T4: −40 °C ≤Ta ≤+70 °C for "T" or "E" types
(Item 14 in the schematic legend) or
T4: 0 °C ≤Ta ≤+50 °C for "S" types
(Item 14 in the schematic legend) or
Environmental class and temperature code for RS40 types:
T3: −40 °C ≤Ta ≤+70 °C for "T" or "E" types
(Item 14 in the schematic legend) or.
T4: −40 °C ≤Ta ≤+60 °C for “T” or “E” types
(item 14 of nomenclature breakdown).
T4: 0 °C ≤Ta ≤+60 °C for “S” types
(item 14 of nomenclature breakdown).
The modules shall be installed in a suitable enclosure in accordance
with EN 60079-15 providing a degree of protection of at least IP54
according to EN 60529, taking into account the environmental
conditions under which the equipment will be used.
When the temperature under rated conditions exceeds 70 °C at the
cable or conduit entry point, or 80 °C at the branching point of the
conductors, the temperature specification of the selected cable and
cable entries shall be in compliance with the actual measured
temperature values.

10 Installation RS20/22/30/32/40
Release 04 02/2015
Make provisions to prevent the voltage of the rated voltage
connections from exceeding the 119 V threshold due to transient
disturbances.
Connectors shall be connected or disconnected exclusively in dead-
voltage state.
DIP switches shall be switched exclusively in dead-voltage state.
The USB port shall remain disconnected.
Relevant for use in explosion hazard areas (Hazardous
Locations, Class I, Division 2):
Applies to North America for devices certified for hazardous locations:
The grid, input and output wiring (I/O) must comply with the requirements
of wiring procedures Class I, Division 2, [Article 501-4(b) of the National
Electrical Code, NFPA 70], and must comply with legal requirements.
ONLY SUITABLE FOR USE IN HAZARDOUS LOCATIONS OF CLASS
I, DIVISION 2, GROUPS A, B, C, AND D, OR IN NON-HAZARDOUS
LOCATIONS.
CAUTION: RISK OF EXPLOSION - REPLACEMENT OF ANY PART
CAN IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
CAUTION: RISK OF EXPLOSION - ONLY DISCONNECT DEVICES
WHEN THE SYSTEM HAS BEEN DE-ENERGIZED OR IS LOCATED IN
AN AREA WITHOUT FLAMMABLE CONCENTRATIONS.
The USB connector is for temporary connection only. Do not use, connect
or disconnect unless the area is known to be non-hazardous. Connection
or disconnection in an explosive atmosphere could result in an explosion.
Peripheral equipment must be suitable for the location in which it is used.
Use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire only.
Avertissement - Risque d'explosion - Ne pas débrancher tant que le
circuit est sous tension à moins que l'emplacement soit connu pour ne
contenir aucune concentration de gaz inflammable.
Avertissement - Risque d'explosion - La substitution de tout composant
peut rendre ce matériel incompatible pour une utilisation en classe I,
division 2.