Beninca DA.SO4 User manual

DA.SO4
®
CENTRALINA A MICROPROCESSORE
CONTROL UNIT WITH MICROCONTROLLER
MIKROCONTROLLER-STEUERUNG
CENTRALE A MICROCONTRÔLEUR
CENTRALITA A MICROPROCESADOR
AUTOMATISMI PER CANCELLI
®
L8542621
Rev. 02/00/01
Libro istruzioni
Operating instructions
Betriebsanleitung
Livret d’instructions
Libro de instrucciones
UNIONE NAZIONALE COSTRUTTORI
AUTOMATISMI PER CANCELLI, PORTE,
SERRANDE ED AFFINI
A
Z
I
E
N
D
A
C
E
R
T
I
F
I
C
A
T
A
UNI
EN ISO
9001

2
Dichiarazione CE di conformità Déclaration CE de conformité
EC declaration of confirmity Declaracion CE de conformidad
EG-Konformitatserklarung
Con la presente dichiariamo che il nostro prodotto
We hereby declare that our product
Hiermit erklaren wir, dass unser Produkt
Nous déclarons par la présente que notre produit
Por la presente declaramos que nuestro producto
DA.SO4
è conforme alle seguenti disposizioni pertinenti:
complies with the following relevant provisions:
folgenden einschlagigen Bestimmungen entspricht:
correspond aux dispositions pertinentes suivantes:
satisface las disposiciones pertinentes siguientes:
Direttiva sulla compatibilità elettromagnetica (89/336/
CCE, 93/68/CEE)
EMC guidelines (89/336/EEC, 93/68/EEC)
EMV-Richtlinie (89/336/EWG, 93/68/EWG)
Directive EMV (89/336/CCE, 93/68/CEE) (Compatibilité
électromagnétique)
Reglamento de compatibilidad electromagnética (89/336/
MCE, 93/68/MCE)
Norme armonizzate applicate in particolare:
Applied harmonized standards, in particular:
Angewendete harmonisierte Normen, insbesondere:
Normes harmonisée utilisées, notamment:
Normas armonizadas utilzadas particularmente:
EN 55022, EN 61000-3-2, EN 61000-3-3, EN 50082-1
Norme e specifiche tecniche nazionali applicate in
particolare:
Applied national technical standards and specifications, in
particular:
Angewendete nationale Normen und technische
Spezifikationen, insbesondere:
Normes et specifications techniques nationales qui ont été
utilisées, notamment:
Normas y especificaciones técnicas nacionales que se
utilizaron particularmente:
UNI 8612
Data/Firma
Direttiva sulla bassa tensione (73/23/CEE, 93/68/CEE)
Low voltage guidelines (73/23/EEC, 93/68/EEC)
Tiefe Spannung Richtlinie (73/23/EWG, 93/68/EWG)
Directive bas voltage (73/23/CEE, 93/68/CEE)
Reglamento de bajo Voltaje (73/23/MCE, 93/68/MCE)
Norme armonizzate applicate in particolare:
Applied harmonized standards, in particular:
Angewendete harmonisierte Normen, insbesondere:
Normes harmonisée utilisées, notamment:
Normas armonizadas utilzadas particularmente:
EN 60204-1, EN 60335-1
Data/Firma
AUTOMATISMI PER CANCELLI
®
Automatismi Benincà Srl
Via Capitello, 45
36066 SANDRIGO (VI)
ITALIA

3
J6
slot. 1 2 3 4
J7 J8 1
st
ch.
2
st
ch.
12V 12V
DA.RB
FUSE
3.15A
1 2 3 4+ -P.M.
PWR
P.P.
M
FUSE
500mA
2
J1
J5
Battery
charger
+ - +
+24V +12V 0V
-
J2 J3 J4
230V
AC
1
FN
24V
DC
3 4 5 6
+ -
ANT.
®
Divisione Elettronica
DA.SO4
®
Div. Elettr.
DA.E

5
DA.SO4 Control unit with microcontroller
The cabinet ”DA.SO4” can be used to control power motors not greater than 20W.
Extension module DA.E
(1,2) Motor = Output, 24VDC motor
(3,4) P.P. = Input, control push button
Operating mode “open – close”
Trimmer P.M. = Adjustment of current limiter activation threshold
Important: Before inserting or replacing the cards “DA.E”, cut-off power supply to the basic board.
Check that the connectors are correctly aligned before powering the circuit.
Mother board
(1,2) 230VAC = Input, power supply 230VAC - 50/60Hz
(3,4) 24VDC = Output, auxiliary 24VDC – Max consumption 1A (”3” negative, ”4” positive)
(5,6) Antenna = Input, antenna for radio receiver.
J1,J2,J3,J4 = Connectors for control cards DA.E.
The cards are inserted at random.
Cut-off power supply to the mother board before inserting or removing the various cards.
J5 = Connector for battery charging card DA.RB.
Connect the negative pole of the battery to terminal “0V” and the positive to terminal ”+24V”;
it is not necessary to connect the intermediate terminal ”+12V”.
J6,J7,J8 = Channel selection of the radio receiver towards the connectors J1, J2, J3, J4.
Example: To connect the 1st channel of the receiver to the connector J3, short circuit J7-J8
in correspondence with column No. 3.
Four-channel radio receiver: in a four-channel receiver, each channel must be connected directly to
inputs “P.P.” of the modules DA.E to be controlled. Selections J6, J7, J8 are valid only if a receiver
connected to connector JRX is used.