Beninca DA.2XS433 User manual

L8542340
Rev. 03/03/00
DA.2XS433
DA.2XSE433
DA.2XS306
CENTRALINA A MICROPROCESSORE
CONTROL UNIT WITH MICROCONTROLLER
MIKROCONTROLLER-STEUERUNG
CENTRALE A MICROCONTRÔLEUR
CENTRALITA A MICROPROCESADOR
Libro istruzioni
Operating instructions
Betriebsanleitung
Livret d’instructions
Libro de instrucciones
UNIONE NAZIONALE COSTRUTTORI
AUTOMATISMI PER CANCELLI, PORTE,
SERRANDE ED AFFINI
A
Z
I
E
N
D
A
C
E
R
T
I
F
I
C
A
T
A
UNI
EN ISO
9001
Intelligent Security & Fire Ltd.

2
Dichiarazione CE di conformità Déclaration CE de conformité
EC declaration of confirmity Declaracion CE de conformidad
EG-Konformitatserklarung
Con la presente dichiariamo che il nostro prodotto
We hereby declare that our product
Hiermit erklaren wir, dass unser Produkt
Nous déclarons par la présente que notre produit
Por la presente declaramos que nuestro producto
DA.2XS433 / DA.2XSE433 / DA.2XS306
è conforme alle seguenti disposizioni pertinenti:
complies with the following relevant provisions:
folgenden einschlagigen Bestimmungen entspricht:
correspond aux dispositions pertinentes suivantes:
satisface las disposiciones pertinentes siguientes:
Direttiva sulla compatibilità elettromagnetica (89/336/
CCE, 93/68/CEE)
EMC guidelines (89/336/EEC, 93/68/EEC)
EMV-Richtlinie (89/336/EWG, 93/68/EWG)
Directive EMV (89/336/CCE, 93/68/CEE) (Compatibilité
électromagnétique)
Reglamento de compatibilidad electromagnética (89/336/
MCE, 93/68/MCE)
Norme armonizzate applicate in particolare:
Applied harmonized standards, in particular:
Angewendete harmonisierte Normen, insbesondere:
Normes harmonisée utilisées, notamment:
Normas armonizadas utilzadas particularmente:
EN 55022, EN 61000-3-2, EN 61000-3-3, EN 50082-1
Norme e specifiche tecniche nazionali applicate in
particolare:
Applied national technical standards and specifications, in
particular:
Angewendete nationale Normen und technische
Spezifikationen, insbesondere:
Normes et specifications techniques nationales qui ont été
utilisées, notamment:
Normas y especificaciones técnicas nacionales que se
utilizaron particularmente:
UNI 8612
Data/Firma
Direttiva sulla bassa tensione (73/23/CEE, 93/68/CEE)
Low voltage guidelines (73/23/EEC, 93/68/EEC)
Tiefe Spannung Richtlinie (73/23/EWG, 93/68/EWG)
Directive bas voltage (73/23/CEE, 93/68/CEE)
Reglamento de bajo Voltaje (73/23/MCE, 93/68/MCE)
Norme armonizzate applicate in particolare:
Applied harmonized standards, in particular:
Angewendete harmonisierte Normen, insbesondere:
Normes harmonisée utilisées, notamment:
Normas armonizadas utilzadas particularmente:
EN 60204-1, EN 60335-1
Data/Firma
Automatismi Benincà Srl
Via Capitello, 45
36066 Sandrigo (VI)
ITALIA
Intelligent Security & Fire Ltd.

3
TR1
D1
R1
C17
U2
U1
R37
U3
C2
C1
D13
K4 R33
C3 R31
C15 D2
D3
D4
R32
D5
R30
R34
R23
R9
C10 R10
C9
R11
C8
R12
C7
R13
C6
R14
C5
R15
C4
Z1
R8
Z2
R7
Z3
R6
Z4
R5
Z5
R4
Z6
R3
Z7
R2
D6
R22
D7
R21
D8
R20
D9
R19 D10 R18
D11
R17 D12 R16
R24 R25 R26 R29 R28 R27
SW3 SW4
Q1
R35
D14
R36
C11
C12
C14
SW2
C13
C16
VD3
VD2
VD1
1F
INPUT
230VAC M
N2
COM. APRE
OUT
24VAC
+V
FCC
FCA
FTC
STOP
P.P.
APRE
CHIUDE
ANT.
CHIUDE 8 9 10
19 18
11 12 13 14 16 17
3 5
VD4
K3 K2 K1
F1 6.3A
6.3A
F1
F2
250mA
FUSE
FUSE
PROG
B.E.
V1.1
MENU
PGM
1 Funz. P.P.
2 Ch. Aut.
3 Cond.
4 Prelamp.
TL/
CODE
TCA/
RES
RX
RX1
ELS.
POWER
Intelligent Security & Fire Ltd.

6
DA.2XS433/DA.2XSE433/DA.2XS306 control unit with microcontroller
The control unit with microprocessor DA.2XS433/DA.2XSE433/DA.2XS306 can be used with motors having a
power not exceeding 750W.
Installation instructions.
a) The electrical installation and functioning logic must comply with current standards.
b) Keep the power cables (for the motor and power supply) away from the control cables (buttons, photo-
cells, radio). To avoid interference use two separate sheaths (see EN 60204-1 15.1.3).
c) Check all the connections again before supplying voltage.
d) Check that the Dip-Switch settings are as required.
e) The normally closed contacts which are not in use should be short-circuited.
f) If the direction of the motor rotation is not correct, invert the ”OPEN” - ”CLOSE” wires of the motor and
the limit switches wires “FCA” - “FCC”.
Input/Output functions
(1,2) INPUT230VAC= Control unit power supply, 230Vac, 50Hz (keep to phase/neutral).
(3,4,5) COM/APRE/CHIUDE= To relevant terminals of motor, at 230Vac, 50Hz.
It is mandatory to connect the Ground wire (yellow/green) onto the motor frame.
(6,7) OUT24VAC= Output, 24Vac auxiliary power supply (100mA max.).
(8) COM= Common to all control inputs.
(9) FCC= Input, closing limit switch (N.C. contact).
(10) FCA= Input, opening limit switch (N.C. contact).
(11) FTC= Input, photocell receiver (N.C. contact).
(12) Stop= Input, Stop push-button (N.C. contact).
(13) P.P.= Input, Step-by-Step push-button (N.O. contact).
(14) Apre= Input, Open push-button (N.O. contact).
(15) Chiude= Input, Close push-button (N.O. contact).
(16,17) ANT.= Input, antenna
In the version DA2XSE only
(18,19) ELS.= Free contact for connection to electric lock.
The power supply of ELS should be provided separately.
If a Flashing light is to be mounted, it should be connected between terminal 1 (input, phase) and terminal 3
(connection to motor common).
The control unit is equipped with a built-in radio module for the reception of both fixed code and variable
code remote controls.
To use a remote control its data should be stored in the unit memory. This procedure is shown hereunder.
The unit is able to memorize up to 14 different codes.
Dip-switch functions
DSW1= Operating mode for “P.P.” (Step-by-Step) button and remote control.
Off= Operation: “APRE” - “STOP” - “CHIUDE” (OPEN - STOP - CLOSE)
On= Operation: “APRE” - “CHIUDE” - “APRE” (OPEN - CLOSE - OPEN)
DSW2= It enables or disables the automatic closure.
Off= Automatic closure disabled
On= Automatic closure enabled
DSW3= It enables or disables the “multi-flat” function.
Off= Multi-flat function disabled
On= Multi-flat function enabled
DSW4= It enables or disables the forewarning flashing light.
Off= Forewarning light disabled
On= Forewarning light enabled
Intelligent Security & Fire Ltd.

7
Programming the control unit
Gain access to the programming mode of the control unit by pressing the MENU push-button.
After the first pressure of the button the PGM LED, which is usually flashing, will feature a fixed light to
indicate that the programming mode has been entered.
Presetting the operating time (TL)
When the PGM and the TL LED’s (first and second from top) are switched on simultaneously, the control unit
is ready to store the operating time in memory. When this time has elapsed, the motor stops even if the limit
switches have not been reached.
The following presetting (Automatic closure) is entered by pressing the MENU button.
When the PROG button is pressed, the motor starts in the opening phase. The motor carries on the opening
movement for as long as the button is kept pressed. When the button is released, the motor stops and the
operating time is memorized. The control unit then exits the programming mode. The time in seconds can be
calculated with the flashing of the TL LED, which performs a flashing each second.
The maximum value of TL is 255 s (4 min and 15 s). Once the maximum value is reached, the control system
stores the value in memory even though the button is not released.
Presetting the automatic closure time (TCA)
The automatic closure time can be preset by pressing the Menu push button twice.
When the PGM and the TCA LED’s (first and third from top) are switched on simultaneously, the control unit
is ready to store the automatic closure in memory.
When the PROG button is pressed, the TCA LED starts flashing and continues flashing for as long as the
button is kept pressed. When the button is released, the LED stops flashing the TCA is memorized. The
control unit then exits the programming mode.
The time in seconds can be calculated with the flashing of the TCA LED, which performs a flashing each
second. The maximum value of TCA is 255 s (4 min and 15 s). Once the maximum value is reached, the
control system stores the value in memory even though the button is not released.
Erasing the remote control codes from memory
The remote control codes can be erased from memory by pressing the Menu push button 3 times.
When the PGM, RX and TCA/RES LED’s (first, third and fourth from top) are switched on simultaneously, the
control unit is ready to erase the codes from memory.
When the PROG button is pressed, the TCA/RES LED switches off and erasing of memory starts; when the
LED starts flashing the operation is ended. If the button is still pressed, the control unit will wait to restart
operation, otherwise it will start immediately.
Storing a new code in memory
A new remote control code can be stored in memory by pressing the Menu push button 4 times.
When the PGM, RX and TL/CODE LED’s (first, second and fourth from top) are switched on simultaneously,
the control unit is ready to store a new code in memory. If RX and TL/CODE LED’s are flashing alternatively,
this means that memory is full and no more new codes can be stored.
By pressing the MENU button it is possible to exit the programming mode.
If memory is not full, the control unit waits for the typing in of the new remote control code. The TL/CODE
LED indicates that programming has been successfully carried out with 5 flashes. The control unit exits the
programming mode automatically.
Intelligent Security & Fire Ltd.

AUTOMATISMI BENINCÀ Srl - Via Capitello, 45 - 36066 Sandrigo (VI) - Tel. [phone] r.a. - Fax [phone]
Intelligent Security & Fire Ltd.