Beok Controls BOT-205 User manual

BOT-205-X Wireless Heating Thermostat User Manual
Programmable Mode Setting
Power on state, long press “ ” enter into first time period (hour setting), press “ ” and “ ” to
adjust value, short press “ ” enter into minute setting, press “ ” and “ ” to adjust value, then short
press “ ” enter into temperature setting, press “ ” and “ ” to adjust value, successively short press
“ ” to set second time period, thirdly time period ......
Wake up
Out door
Back home
Out door
Back home
Sleep
6：00 20℃8：00 15℃11：30 15℃13：30 15℃17：00 20℃22：00 15℃
Product Specifications
☆Power Supply: Receiver:230Vac 50/60HZ
☆Range of temperature display: 0~40°C
Advanced options
Power off state, long press
From A1 to Ao, short press
Transmitter: 2AA* 1.5V alkaline batteries
for 3-5 seconds to access advanced setting.
to choose the option, and adjust data by
☆Display accuracy: 0.5°C
☆Insulating condition: Normal environment
☆Running program: Set per 1 week as a cycle
,
. After finish setting ,remain
☆Probe sensor: NTC(10k)1%
about 5 seconds ,it will save setting and exit advanced setting automatically .
☆Contact capacity: 5A/250V(BW;WW);16A/250V(WE)☆Output: Switch relay
NO
Setting Options
Data Setting Function
Factory Default
Display
☆Working environment temperature: 0~70°C
☆Range of temperature adjustment: 5~35°C
Operation Key
☆Installation: Wall mounted or on battery seat
☆Size(mm)：86*86*27
Measure Temperature
Calibration
-9-+9℃
A1
measuring
temperature
1℃
press
, to adjust.
NO
A
symbols represent
Temperature
control
return 0.5-2.5℃
A2
Turn ON/OFF: Short press to turn on/ turn off
difference setting
A3 Children lock setting
A4 Power off Memory
0:half lock
1:full lock
0
0
B
1 Short press
to switch automatic mode and manual mode
for 3-5 seconds to enter into programmable
2 Turn on thermostat, long press
0: Last State
setting
1: Electricity turn off
3. Turn off thermostat, long press
for 3-5 seconds to enter into advanced setting
2: Electricity turn on
C
1 Confirm key: use it with
key
P1: 5+2
P2: 6+1
P3: 7
P1
2 Only short press it to set time
A5 Weekly programming selection
A6 Setting temperature lowest limit
3 Turn on thermostat, long press it for 3-5seconds to holiday mode setting
1-10℃
5℃
B
1 Decrease key
2 Long press to lock /unlock
1 Increase key :
A7 Setting temperature highest Limit 20-70℃
1: 1-10℃
35℃
D
2 Under auto mode state, press
,
to enter into temporary manual mode
A8 Anti-freezing function
2: more than 10℃,display -- ,then
mean closed this function
1: 5-35℃
5℃
3 Long press to check external sensor temperature(only used for the receiver with
external sensor)
--
Highest temperature protection 2: less than 35℃,display --,then mean
function closed this function
A9
Icon Instruction
Return different temperature of 1-9℃
2
AA
external sensor
Display A o, long press
the whole screen
until show
Ao Restore factory defaults
Power off state, long press
From B1 to B5, short press
for 3-5 seconds to access advanced setting.
to choose the option, and adjust data by
,
. After finish setting ,remain

about 5 seconds ,it will save setting and exit advanced setting automatically .
NO Setting Options Data Setting Function
Wiring Diagram
Factory
Default
00
B1 IP code low setting
B2 IP code high setting
00-FF
01-FF
01
Power on RF Receiver ,continue press
until Display”55” means IP match
successfully.
B3 Write transceiver IP address
B4 Choose “C” or “F” display
00
0: C ( Celsius)
0
1: F (Fahrenheit)
B5 Version No.
10：V1.0
Setting IP code
Cautions on Installation and Use
Turn on the receiver, and keep the transmitter on power off state, long press button
enter into setting interface.
for 3-5 seconds to
1.
To prevent the thermostat display from a high fluctuation, special treatment has been made to the program. Therefore,
it is normal that the thermostat cannot immediately display the sudden change of temperature.
The thermostat installed on 1.5m above the ground.
B1:press or to set any number or letter(if you have more than one transceiver, make sure to set
different number or letter for each transceiver )
2.
3.
For the thermostat installed, please take care not to install it to the wall corner, door / window side or behind the door
or in such unheated area as exterior wall. Avoid hot / cold air duct, radiator, flue or thermal pipe.
If you have any problem for the installed ,please contact our company hysen, we will make a demonstration for you
Only the professional technicians are permitted to open the transmitter and receiver box of the thermostat for
installation. When install the power supply, make sure that the power cable is well insulated.
The thermostat is unrepairable product. The user shall not open the internal circuit board.
Then press
transceiver, make sure to set different number or letter for each transceiver )
Then press to switch to B3 , continuously click until the transmitter display “55”means that
to switch to B2:press or to set any number or letter(if you have more than one
4.
5.
matched successfully
Transceiver tips
Receiver LED display instruction:
Power light (green light):it’s bright when power on
6.
7.
Before installing the thermostat, make sure that the system is disconnected. The maximum voltage of the system shall
meet therequirements specified intheInstruction Manual(Max. AC Voltage: 240V).
Signal light(orange light):it’s bright within 10s after power on (match IP),signal light off when it receive
match, signal light is blinking within 10s after power off.
Load light/fault light (red light):
A、When no fault: light bright when load output, light off when no load output
B、When fault: 1. Light blink 2 times indicate IP is fault
Warranty：
We offer the warranty of 24 months, from the sales day. The products of our company can have lifetime
warranty ,if it is not the quality problems, or beyond the warranty period, we will charge for the after-sale
service.
2. Light blink 3 times indicate it does not receive wireless signal for 1 hour
3. Light blink 4 times indicate built-out sensor is fault(only for receiver with external
sensor )
Sensor fault display: please choose correct working way of built-in and external sensor, if choose
wrongly or sensor fault (breakdown), “E1”or “E2”will be displayed on the screen. Thermostat will stop
heating until the fault is eliminated.