Berlin Gardens PGST2400 Firmware update

Assembly Directions for
Gliding Settee Table
Hardware Package
4 2½"Screws
82"Screws
12345
Use to measure bolts
Tools Needed:
Screw Gun w/ Square Drive Bit
Poly Models #OGST2400 & PGST2400
Proper Care of your Fine Piece of
Wooden Lawn Furniture: is lawn
furniture is constructed with premium
quality treated southern yellow pine.
is wood was dried after treatment
and milled. You do not have to wait
for any curing process. Even though
this wood is first quality and much
care has been given to make sure the
craftsmanship is also first quality, it still
needs a sealer to protect it from the
elements to avoid excessive checking
or warping. e manufacturer
recommends you see the store where
you bought this furniture for the
proper sealer.
Proper Care for Poly Lawn
Furniture: Any mild, non-abrasive
household cleaner is safe to use for
cleaning your fine piece of poly lawn
furniture.
First, fasten wedge to bottom of 2"x6"
with 2½"screws. Ensure that the side
of wedge and the end of 2"x6"are flush.
2½"screws
en, mark location of Quick Attach
bracket with template provided. Fasten
with 2"screws.
2"Screws
#PGST2400
HARDWARE PACKAGE
4 2½" Screws
8 2" Screws
PACKAGE CONTENTS
1Settee Table
2 Quick Attach Brackets
1 Hardware Package
TOOLS NEEDED:
Screw Gun with
Square Drive Bit
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
Assembly Directions for
Gliding Settee Table
Assembly Directions for
Gliding Settee Table
Hardware Package
4 2½"Screws
82"Screws
12345
Use to measure bolts
Tools Needed:
Screw Gun w/ Square Drive Bit
Poly Models #OGST2400 & PGST2400
Proper Care of your Fine Piece of
Wooden Lawn Furniture: is lawn
furniture is constructed with premium
quality treated southern yellow pine.
is wood was dried after treatment
and milled. You do not have to wait
for any curing process. Even though
this wood is first quality and much
care has been given to make sure the
craftsmanship is also first quality, it still
needs a sealer to protect it from the
elements to avoid excessive checking
or warping. e manufacturer
recommends you see the store where
you bought this furniture for the
proper sealer.
Proper Care for Poly Lawn
Furniture: Any mild, non-abrasive
household cleaner is safe to use for
cleaning your fine piece of poly lawn
furniture.
First, fasten wedge to bottom of 2"x6"
with 2½"screws. Ensure that the side
of wedge and the end of 2"x6"are flush.
2½"screws
en, mark location of Quick Attach
bracket with template provided. Fasten
with 2"screws.
2"Screws
bracket
2x6
Top Board
w/cupholder
w/umbrellahole
Top Support
Slat
2x10
Wedge

Top Part of Bracket
Match With Hole In Glider Base
Front of base
Quick
Attach
Bracket
Here
Template To Make Quick Attach Bracket On Glider Base
<
Keep
Bottom
Of Bracket
Aligned With
This Line
V
l

#PCTG2400, #PZTG2400
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
Single Comfo-Back Glider
Assembly Directions for
Single Gliders
PACKAGE CONTENTS
2Bases
1Back
1Seat
1 Hardware Package
2 Arms with Legs
2 Cross Supports
4Stops
1 Glider Bracket Package
TOOLS NEEDED:
Hammer
⁄" Wrench
½" Wrench
Allen Wrench (Included)
HARDWARE PACKAGE
8 • ¼” x 2” Allen Head Bolts
2 • ¼” x 4½” Allen Head Bolts
2 • ¼” x 3½” Allen Head Bolts
6 • ¼” x 3” Allen Head Bolts
8 • 5/16” x 2 1/2” Allen Head Bolts
8 • 5/16” Lock Nuts
8 • 5/16” Flange Nuts
18 • 1/4” Flange Nuts
4 • 5/16” Acorn Nuts
4 • Aluminum Spacers
4 • Glider Brackets
1 • Allen Wrench
Single Cozi-Back Glider
Back Slat
Seat Slat
Leg Brace
Seat
Support
Base Assembly
Leg
Right Arm
Le Arm

STEP #1 - Fasten the Arm and Leg Assembly to the
Seat and Back using 3- ¼" Allen Head
Bolts. Using a hammer, firmly tap the Bolts
until they are flush with the poly surface.
Securely tighten using 3- ¼" Flange Nuts.
¼" x 3½" Allen Head Bolt
¼" x 3" Allen Head Bolt
¼" x 4½" Allen Head Bolt
STEP #2 - Turn the chair on the other side and repeat
Step #1.
STEP #3 - Using 4- ⁄" x 2½" Allen Head Bolts, place
them into the pre-drilled holes and tighten
using 4- ⁄" Flange Nuts. (Ensure the
Bolts are pointing inwards.)
¼" x 3½" Allen Head Bolt
¼" x 4½" Allen Head Bolt
¼" x 3" Allen Head Bolt
5/16" x 2½" Allen Head Bolts

STEP #1 - Fasten the two Cross Supports to the Base
using 8- ¼" x 2" Allen Head Bolts and 8-
¼" Flange Nuts.
STEP #3 - Locate the predrilled holes located on
outside edge of glider base and install glide
assembly (see next step).
STEP #2 - Attach the four Glider Stops to the Base
using 4- ¼" x 3" Allen Head Bolts and
4- ¼" Flange Nuts. Insert the Allen Head
Bolts into the Poly Glider stops and place
into pre-drilled holes on base. Firmly
fasten with the a ¼" ange nut.
¼" x 2" Allen Head Bolts
¼" x 3" Allen Head Bolts
Front of Base
Back of Base

Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
First slide the Glider Bracket onto the ⁄”x2-½” Allen
Head Bolt, secondly slide the round ⁄” Aluminum
spacer onto the Allen Head Bolt, positioning the alu-
minum spacer beside the glider bracket . Once this
sequence is complete place the bolt into the pre-drilled
holes on swivel glider base.
Firmly tighten the Allen Head Bolt with the ⁄” lock
nut and place the ⁄” cap nut at the end of bolt se-
quence.
Repeat this step for the remaining glider brackets.
⁄X2-½” Allen Head Bolt
Glider Bracket
⁄” Aluminum Spacer
⁄” Lock Nut
⁄”Acorn Nut
First slide the Glider Base underneath
the Glider Chair, ensuring the correct
end of the base is pointed forward (see
photo). en li the Glider Brackets
onto the ⁄" x 2½"Allen Head Bolts
previously installed onto the Glider
Legs. Secondly Using 4- ⁄" Lock Nuts,
secure Glider Bracket onto the
Bolt securing the bracket next the ange
nut (leg side) and lock nut (outside).
Repeat this step on the remaing glider
brackets.
⁄X2-½” Allen Head Bolt
⁄” Flange Nut Nut
Glider Bracket
⁄” Lock Nut
Back of Base Front of Base