Berlin Gardens Mathew Sling Dining Arm Chair MHSDAC2236 User manual

Step 1 Step 2
LEG BRACE ASSEMBLY DETAIL
Cordless Drill
#2 Square Drive Bit
(included)
+
A
x6
B
x8
3" Bugle Head Sc ew
2" Pan Deck Sc ew
Ha wa e Included Tools Needed
Assembly Guide
MHSDAC2236
Mayhe Sling Dining Arm Chair
A x 1
A x 1
A x 2
A x 2
A x 2
A x 1
B x 2 B x 2
B x 2
B x 2
B x 2
SEAT ASSEMBLY DETAIL
Fit the mortises & tendons
in the seat and back into
each other and fasten
using the indicated scre s
in pre-drilled holes
ARM ASSEMBLY DETAIL
Place the back against
the arm support in the
notched area and fasten
using indicated scre s
in predrilled holes
Properly position the leg brace assembly
bet een the chair legs by fitting the mortise
and tendon jointery in each corner.
Fasten the leg brace assembly
to each chair legs using the indicated
scre s in the pre-drilled pocket holes

Step 1
Set the Arm and Seat Assembly forward onto the front of the
Arms and set the Back Assembly on top. Be sure to do this
on top of a soft surface to avoid damaging the arms.
Fasten the Back to the Seat using eight - 4" Buglehead Screws.
Keeping the Arms Supports even with the outside edges of the
Back, fasten them using two - 3" Buglehead Screws.
Mayhew Sling
Dining Swivel Rocker
Assembly Guide
Tools Required
Hardware Included
Cordless Drill #2 Square Drive Bit
(Included)
Allen Wrench
(Included)
2 - 3"
Buglehead
Screws
8 - 4"
Buglehead
Screws
Back Assembly
Arm & Seat Assembly
Keep the Arm Support even with the outside edge of the Back.
3" Buglehead Screws 4" Buglehead Screws
Wrench
6 - 5/16" X 1 3/4"
Allen Head Bolts
6 - 5/16"
Flange Nuts
6 - 5/16"
Lock Washers
6 - 5/16"
Square Nuts
3 - Fiberglass Springs
3 - Aluminum Plates
1 - Swivel Mechanism
6 - 5/16" X 1 1/4"
Allen Head Bolts

Step 2
Step 4
Lift the top of the chair and set the swivel stem
into the receiver of the base. Push firmly onto the
chair until it sits securely in the receiver.
Step 2 Detail
Step 3 Detail
Using 6 - 5/16"x 1 1/4"
Allenhead Bolts and
5/16" Flangenuts, fasten the
3-Fiberglass Springs
and 1 - Aluminum
Plate to the seat bracket
The Springs should point
towards the front of the
chair. Only hand tighten
the nuts until all six bolts
are installed, then align the
springs and fully tighten.
5/16" Flange Nuts
5/16" x 1 1/4" Bolts
Aluminum Plate
Fiberglass Springs
Fasten the Swivel Mechanism to
the Figerglass Springs, using
2-Aluminum Plates, 6 - 5/16"x 1 3/4"
Allenhead Bolts, Lock Washers
and Square Nuts. Only hand tighten
the nuts until all six bolts are
installed then fully tighten.
Fiberglass Springs
5/16" x 1 3/4" Bolts
Aluminum Plate
Aluminum Plate
Swivel Mechanism
5/16" Lock Washers
5/16" Square Nuts
Step 3

#GCIT4472D, #GCIT4472C, #GCIT4472B
in Garden Classic Collection
HARDWARE PACKAGE
16 ¼" x 2" Allen Head Bolts
16 ¼" Flange Nuts
2 Umbrella Knobs
44 3" Screws
24 1½" Screws
1Allen Wrench
PACKAGE CONTENTS
1Top
4 Bases
4 Long Cross Supports
2 Short Cross Supports
4 Footrests (Bar and Counter Height)
1 Umbrella Holder
1 Umbrella Plug
8 Braces
1 Hardware Package
TOOLS NEEDED:
Hammer
7/" Wrench
Cordless Drill/Screwdriver
Allen Wrench (Included)
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
Garden Classic Table
NOTE: Bar
and Counter
Height Only
Assembly Directions for
44"x72" Rectangular Table
Be sure to
use 1½"
screws when
fastening
braces.
!
Base
Long Cross Support
Short Cross Support
Upright
Top Boards
Apron
Brace
Umbrella
Holder
Curved End Board
Footrest
Garden Classic
Table

STEP #1 - First assemble both Bases and Long Cross
Supports using 3" Screws.
Please note: ere are two outside Bases and
two center Bases. e two center Bases have
extra mortises for the Umbrella Holder and
Short Cross Supports (see Step #3).
STEP #2 - Attach the rst Base Assembly to the
aluminum frame of the Top using
8- ¼" x 2" Allen Head Bolts.
STEP #3 - Attach the two Short Cross Supports and the
Umbrella Holder to the Base using 3" Screws.
STEP #4 - First attach the second Base Assembly to the
aluminum Frame of the Top using 8- ¼" x 2"
Allen Head Bolts. Second fasten the Base
Assembly to the Short Cross Pieces and
Umbrella Holder using 3" Screws.
STEP #5 - Last, attach the Braces to the Top and the Base
using 1½" Screws.
Caution: Do not overtighten the Screws into
the Top!
Umbrella
Knobs
¼" x 2" Allen Head Bolts
3" Screws
3" Screws
3" Screws
¼" x 2" Allen Head Bolts
Footrest
1½" Screws (circled)
Cross Support