Wine racks America Solid Diamond Cube User manual

Solid Diamond Cube
Assembly GUIDE
Cordless Drill Finish Nailer
Hammer Nail Setter
Rubber Mallet
Wood Glue
*Please verify that you have the correct number of parts before proceeding.
Depending on the model you purchased, your bundle should contain the following:
Package Contents tools for assembly
Page 1
or visit
wineracksamerica.com
Questions?
888.373.6057
Required
Suggested
Screwdriver
Side Panel
Top Panel
Bottom Panel
WOOD SCREWS FINISH NAILS
Trim Piece
Long Middle
Short Middle
34 7/8"
34 7/8"
TOP PANEL (x1)
47 1/4"
47 1/4"
LONG MIDDLE (x2)
BOTTOM PANEL (x1)
33 7/8"
33 7/8"
TRIM PIECE (x1)
34 7/8"
SIDE PANEL (x2)
35 5/16"
SMALL MIDDLE (x4)
23 5/8"
SHIM (x1)
10"
WOOD PUTTY
SCAN FOR
ASSEMBLY VIDEO

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Solid Diamond Cube
Page 2
1. Find an open, flat area in which to work. Carefully remove all components from the box and remove banding or
protective wrapping. Check the parts list to verify package contents.
1
ATTACH SIDES
TO BOTTOM
2. Using the provided wood screws, attach the bottom panel into the grooves of the two side panels. (figure 1)
3. Attach the top panel to the side panel pieces using the wood srews provided. Make sure to keep the side panels
and top panel held tightly together when securing.
It may be easier to stand the rack upright when securing the top frame piece. (figure 2)
2
SECURE TOP
TO FRAME
BOTTOM
OF RACK

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Solid Diamond Cube
Page 3
4. Now that the frame of the rack is assembled, insert the first long middle into the frame of the rack with the
notches facing upward. (figure 3)
5.
Insert the second long middle into the frame. The long middle pieces will join at the middle notch and slide down
into place. (figure 4)
BOTTOM
OF RACK
BOTTOM
OF RACK
NOTCHES
TIP: DO NOT FORCE! Carefully work the shelves into the frame by hand until they settle flush with the sides.
If necessary, use a rubber mallet to lightly tap the shelf pieces into place.
3
INSERT FIRST
LONG MIDDLE
4
INSERT SECOND
LONG MIDDLE
BOTTOM
OF RACK
BOTTOM
OF RACK
6. Insert the first two small middle pieces into the frame. The notches on the small middle pieces will interlock
with the notches on the long middle piece and slide down into place. (figure 5)
Flip rack over and repeat step 6 for the final two small middle pieces. (figure 6)
5
INSERT FIRST
SMALL MIDDLE
6
INSERT SECOND
SMALL MIDDLE

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Solid Diamond Cube
Page 4
BOTTOM
OF RACK
7. At this point, there is no specific front of the rack. Choose the side of the rack that you would like to be the front
and secure the bottom trim piece. The bottom trim piece should be flush with the bottom of the rack. (figure 7)
We recommend that you use a finish nailer to drive a nail through the trim piece into each side frame piece.
If you do not have a finish nailer, drive one of the provided finish nails into each side frame piece using a hammer
until it is flush with the surface trim piece. Use wood glue for added support.
Fill the nail holes using the wood putty provided. Push a small amount of putty into each hole and wipe excess putty
off the surface using a damp cloth.
7
ATTACH BOTTOM
TRIM PIECE
9. If you purchased a solid top, secure it by placing a small amount of wood glue on the top of the box frame. Clamp
the top to the frame using standard wood clamps until fully dry. (figure 9)
8. To prevent the bottom of the rack from bowing under the weight of your bottles, slide the bottom frame shim
under the back of the rack. (figure 8)
FRONT
OF RACK
8
INSERT SHIM
PIECE
9
AT TA C H
BUTCHER BLOCK
360 North 700 West Suite F • North Salt Lake, UT 84054
(toll free) 888-373-6057
(fax) 801-936-0534
Once again, thank you for your business. Remember, customer
service is available to answer any questions Monday-Friday
7:00 am - 5:00 pm MST. Please feel free to contact us for any
wine storage needs.
We would love to see your wine racks in use! Please feel free to
send any photos of your rack to [email protected]
WINERACKSAMERICA.COM