Birlea MERLIN HIGH SLEEPER User manual

Page 1 of 25
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR
MERLIN HIGH SLEEPER FRAME.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HEALTH & SAFETY:
DO NOT jump on this bed frame.
DO NOT use this bed frame if any parts are missing, damage or worn.
DO NOT use this bed frame unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
This bed is tested to European safety standard BS EN 747-1 & 2:2012+4I:2015
WARNING: If this bed is placed on a non-carpeted floor you must place some protection under all legs to stop
the bed frame from moving. If this is not adhered to there is no guarantee if the bed frame collapses.
WARNING: High beds are not suitable for use by children under 6 years of age due to risk of injury from falls.
WARNING: Please note the area underneath the bed is to used for storage purpose only
WARNING: High beds present a serious risk of injury from strangulation if used incorrectly. Never attach or
hang anything on any part of the frame that is not designed to be used with the bed, for example, but not
limited to ropes, strings, cords, hooks, belts, and bags.
WARNING: Do not use the high bed if any structural part is missing or broken.
WARNING: Children can become trapped between the bed and adjoining structures including walls, roof
pitches, ceilings and other pieces of furniture. To avoid risk of serious injury, the distance between the top
safety barrier and any adjoining structure shall not exceed 75mm or shall be more than 230mm.
CARE & MAINTENANCE:
Assemble in the room of use.
Assemble on a soft, clean surface.
Please check regularly that all assembly fastening are properly tightened.
DO NOT push the bed frame as this will damage the legs.
Always lift the bed with two people to reposition.
Use a soft, dry cloth to clean - do not use any detergents or chemicals.
Avoid contact with water and direct sunlight. Do not place bed near heat sources, window to keep the
humidity low and prevent mould in and around the bed
INFORMATION
- Maximum thickness of mattress 15cm. Please refer to making headboard.
- Recommend size of mattress L192cm x W92cm x H15cm
- When you are ready to start, make sure that you have the right tools, plenty of space on a clean, dry area
for assembly.
- Check the pack and make sure you have all the part listed.
- Ensure that this product is fully assembly and secured as illustrated before use.
ASSEMBLY INSTRUCTIONS
MERLIN HIGH SLEEPER

Page 2 of 25
1
2
3
4
5
6
7
8
9
10
11
11
11
12 x 3
13 x 3
14
15
16
17
18 19
20
21
22
23
24
25
26
28 27
29
30
31
32
33

PARTS LIST HARDWARE LIST: Carton 2 of 3
Part Description Qty
Part Description Qty
3Back Side Panel 1
ACAM NUT 15mm 4
BCAM BOLT 4
C WOOD DOWEL M8 x 30mm 47
DJCBC SCREW M6 x 50mm 10
EM6 STEEL NUT 10
FM6 x 40mm UNITAR SCREW 60
G CSK SCREW M4 x 38mm 4
HCSK SCREW M4 x 25mm 2
ICSK SCREW M4 x 16mm 30
JCSK SCREW M4 x 12mm 16
KPVC FEET NAIL 14
L NAIL 8
MMETAL SHELF SUPPORT 4
Page 3 of 25
Carton 1 of 4:
4 Back Base Panel 1
5 Front Base Panel 1
8 Base Bottom Support Panel 1
Part Description Qty
1Left Side Panel 1
Carton 2 of 4:
1
131 Table Back Panel
132 Cabinet Back Panel
2Right Side Panel
** You will need a screwdriver and a small mallet
( NOT provided)
** WARNING: THE USE OF
POWER TOOLS TO ASSEMBLE
THIS PRODUCT WILL
INVALIDATE ANY CLAIM AND
MAY DAMAGE THIS PRODUCT
MAKING IT UNSAFE.
NVK-43 ALUMINIUM BRACKET 2
O OVAL PIPE 573mm 1
PDOOR STOPPER 2
Q MDF SUPPORT 4
RMETAL L-BRACKET 3
SHINGES 78"3
TMETAL RUNNER TRUCK 14" 1set
UMETAL RUNNER 14" 1set
V ALLEN KEY 1
W STICKER 17
XHOLE CAP 35mm 1
Part Description Qty
6Left Front Side Panel
Carton 3 of 4:
7Right Front Side Panel
9 Left Panel 1
10 Right Panel 1
11 Ladder Back Panel 3
12 Ladder Bottom Support Panel 3
13 Ladder Step Panel 3
14 Cabinet Bottom Panel 1
15 Cabinet Plinth Panel (Front) 1
16 Cabinet Back Support Panel 1
17 Support Panel 1
21 Table Left Panel 1
Hardware List
22 Bottom Support Panel 1
23 Table Bottom Panel 1
24 Movable Panel
25 Table Plinth Panel 1
26 Drawer Front Panel 1
27 Drawer Back Panel 1
28 Drawer Left Panel 1
29 Drawer Right Panel 1
130 Drawer Bottom Panel
Part Description Qty
1
Carton 4 of 4:
1
119 Table Top
1
20 Table Back Panel
118 Door
1
33 Cabinet Plinth Panel (Back) 1

1
1
K
A2
B2
C40
2
H
Page 4 of 25
2
8
11 x 2
11
14
15
16
28
29
26
13 x 3
12 x 3
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
A
A
B
B
17
I
I
HH
Q
Q
Q
Q
K
K
K
K
K
K
J
T
T
N
2
I
3
J
7
K
N1
Q 4
T1
Insert hardware part A & part B using a screwdriver (not provided). Insert hardware part C
using a small mallet (not provided). Insert hardware part K using a small mallet (not
provided). Attach hardware part T with screw J using screwdriver (not provided). Insert
hardware Q using a small mallet (not provided). Attach hardware N with screw I using
screwdriver (not provided). Attach support panel (17) to left side panel (1) using hardware
(H).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
33
C
C
C
C
K

2A2
B2
C7
Page 5 of 25
18
10
9
19
21
25
22
A
A
B
B
K
K
K
K
KK
K
J
T
T
K
C
C
C
C
I
S
I
S
S
S
N
P
P
I
I
I
I
C
10
I
3
J
7
K
2
P
1
N
3
S
1
T
C
C
Insert hardware part A & part B using a screwdriver (not provided). Insert
hardware part C using a small mallet (not provided). Insert hardware part K
using a small mallet (not provided). Attach hardware N with screw I using screwdriver (not
provided). Attach hardware door stopper P by screw I by using screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.

3
4F6
Page 6 of 25
F
F
10
22
21
F2
F
F
F
F
F
F
10
21
13 12
13
12
12
13
Attach the right panel (10) and table left panel (21) to the bottom support panel (22) with
screw (F) by using allen key (V) and tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V
Attach the ladder bottom support panel (12) and ladder step panel (13) to the right panel
(10) with screw (F) by using allen key (V) and tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V

5
6
Page 7 of 25
11
11
11
with PVC Nail
F
F
F
F
F
F
9
F6
Attach the ladder back panel (11) to right panel.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V
Attach the left panel (9) to the ladder back panel (11) with screw (F) by using allen key (V)
and tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.

7
8
F1
F2
Page 8 of 25
F
15
33
16
9
22
21
F
F
14
Attach cabinet back support panel (16) to left panel (9) with screw (F) by using allen key (V)
and tighten clockwise. Attach cabinet plinth panel (15) and (33) to left panel (9).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V
Attach cabinet bottom panel (14) to left panel (9) with screw (F) by using allen key (V) and
tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V

9
10 F2
Page 9 of 25
F
F
F
1
14
F
F
21
23
25
F3Attach left side panel (1) to bottom panel (14) and back support panel (16) with screw (F) by
using allen key (V) and tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V
Attach table bottom panel (23) to table left panel (21) with screw (F) by using allen key (V)
and tighten clockwise. Attach table plinth panel (25) to table left panel (21).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V

11
12 F4
Page 10 of 25
19
21
23
Lock
B
A
B
Unlock
F
F
F
F
19
20
31
Fix the table top (19) to the table left panel (21) by using a screwdriver (not providedDO NOT
use any power tools as this may damage the frame and will invalidate any claim.
V
Attach table back panel (20) to table left panel (21) with screw (F) by using allen key (V) and
tighten clockwise. Insert table back panel (31) as shown.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.

13
14
F3
Page 11 of 25
F
F
F
19
20
D
8
1
E
E1
D1
Fix table back panel (20) to table top panel (19) with screw (F) by using allen key (V) and
tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V
V
Attach back bottom panel (8) to left side panel (1) with screw (D) & hardware (E) by using
allen key (V) and tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.

15 D1
Page 12 of 25
D
F
F
F
F
F
F
E
E1
F6
2
820
19
Attach right side panel (2) with screw (D) & screw (F) by using allen key (V) and tighten
clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V

16 J4
Page 13 of 25
L9
J
J
J
J
L
L
L
L
L
L
L
L
32
L
Attach cabinet back panel (32) with screw (J) using a screwdriver (not provided) and nail (L)
by using small mallet (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.

17
Page 14 of 25
F
F
F
F
F4
4
V
Fix back base panel (4) with screw (F) by using allen key (V) and tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Page 15 of 25
D
E
D
E
E
E
D
D
3
F
F
F
18 D4
E4
F3
Fix back side panel (3) with screw (D) & hardware (E) by using allen key (V) and tighten
clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V

Page 16 of 25
19 F12
F
F
F
F
F
F
F
F
F
FF
F
4
5
Attach front base panel (5) with screw (F) by using allen key (V) and tighten clockwise.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
V

Page 17 of 25
20 D4
6
E
D
E
D
D
E
D
E
R
I
I
R
R
R
E4
I12
R3
Attach left and right front side panels (6) & (7) with screw (D) and hardware (E) by using
allen key (V) and tighten clockwise.
Fix hardware (R) with screw (I) by using screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
7
V

Page 18 of 25
O
M
MM
M
21
M4
O1
F
F
F
F
F
F
F6
V
Fix left and right front side panels (6) & (7) with screw (F) by using allen key (V) and tighten
clockwise.
Insert hanger pipe (O) and hardware (M) as shown.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
6
7

Page 19 of 25
18
6
I
22
I
I
I
24
Door Door Door
Front to Front Adjustment Lateral Adjustment Vertical Adjustment
Fix door panel (18) to left side panel (1) with hinges (S) and screw (I) using a screwdriver
(not provided).
Insert movable panel (24) as shown.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.