Body Craft MA906 User manual

Jones Freedom Strength Training System
OWNERS MANUAL
MA906 Recreation Supply Inc.
Model No. P.O. BOX 181
BODYCRAFT is a division of Recreation Supply Sunbury, OH 43074

1
25
25
34
34
34 37
37 34
30
15
31
25
34
34
37
37
34
30
25
34
1
2
8
8
9L
9R
2
3
5
6
16
11
20
16
20
21
19
12
13
13
36
31
33
17
36
33
14
15
15
14
18
24
37
37
34
34
37
34
34
37
33
29
24
23
33
33
36
33
33
18 29
33
28 36
36
33
11
20
16
19
20
21
16
6
7
7
4
23
34
23
33
32
24
33
33
36
34
34
23
32
26
26
12
23
36
33
24 33
25
25
34
25
34
14
15
14
31
29
33
36
29
28
31
31
34
22
27
35
27
35
10
10
33
33 22
22
22
33
33
34
33
36
33
31
31
36
OVERVIEW
2

1
2
3
4
5
6
7
8
9L
9R
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
2
2
1
1
1
2
2
2
1
1
2
2
2
2
4
4
4
2
2
2
4
2
4
8
2
8
8
2
2
10
2
10
2
26
32
2
14
16
BASE FRAME
BASE FRAME CONNECTOR
LOGO PANEL
OLYMPIC BAR
TOP FRAME
UPRIGHT FRAME
VERTICAL GUIDE ROD
(preassembled on Uprights)
HORIZONTAL GUIDE ROD
(pre-assembled in Base Frame)
LEFT BASE BEARING HOUSING
(pre-assembled in Base Frame)
RIGHT BASE BEARING HOUSING
(pre-assembled in Base Frame)
TRIM
VERTICAL BEARING HOUSING
(preassembled on Uprights)
SAFETY SPOTTER
(preassembled on Uprights)
HOOK PLATE
(preassembled with Safety Spotter)
30mm BEARING
(preassembled in Base Frame)
RUBBER STOPPER
(preassembled in Base Frame)
25mm BEARING
(preassembled in Olympic Bar)
2" SQ. PLUG
POP PIN
SPRING
RETAINING RING
(pre-assembled in Bar)
1" ID BIG WASHER
(preassembled on Uprights)
1/2" X 3-1/8" HEX BOLT
1/2" X 3" HEX BOLT
1/2" X 2-1/2" HEX BOLT
3/8" X 4" HEX BOLT
3/8" X 1-1/4" HEX BOLT
5/16" X 1/2" INNER HEX SCREW
M8 X 16L COUNTER ALLEN BOLT
M8 X 19L ALLEN BOLT
5/16" X 5/8" SET SCREW
5/16" X 1/4" SET SCREW
1/2" LARGER WASHER
1/2" SMALL WASHER
3/8" WASHER
5/16" WASHER
1/2" NYLON NUT
3/8" NYLON NUT
PARTS LIST
NO. DESCRIPTION QTY.
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
3
1
2
6 7 8
9L 9R 11 12 13 14
15 16 17 18
22 27
32 36
3733
34
35
28
29
23
24
25 30
26 31
19 20 21
3
4
5
10

STEP 1 Base Frame Assembly
IMPORTANT:
˙ To ease the assembly process, DO NOT tighten bolts until instructed.
˙ Please assemble on a flat level floor.
˙ Assembly requires three people during installation of the TOP FRAME.
1. Attach BASE FRAME CONNECTORS (2) to the two BASE FRAMES (1), using
eight 3/8" X 4" HEX BOLTS (25), sixteen 3/8" WASHERS (34), and eight 3/8"
NYLON NUTS (37).
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
ENSURE BASE
FRAMES ARE
PARALLEL AND
TIGHTEN ALL BOLTS.
25
34
34
37
37
34
34
25
25
34
34
34
34
37
37
1
34
25
34
1
2
2
4

STEP 2 Upright Frame Assembly
5
1. Attach the VERTICAL GUIDE ROD (7) to the BASE FRAME
(1). Attach UPRIGHT FRAME (6) to the LEFT BASE
BEARING HOUSING (11) using three 1/2" X 2-1/2" HEX
BOLTS (24), five 1/2" WASHERS (33) and two 1/2" NYLON
NUT (36).
2. Repeat above step for right side.
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
24
24
24
6
17
17
7
7
6
24
33
9L
33
33
33 36
36
31
33
36
36
33
31
9R

STEP 3 Safety Spotter Assembly
6
1. Attach the VERTICAL BEARING HOUSING (11), 1" ID BIG
WASHER (21), SPRING (19), and SAFETY SPOTTER (12)
to the VERTICAL GUIDE ROD (7).
2. Repeat above step for right side.
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
11
21
19
12
7
6
7
6
11
9L
21
9L
9R
19
12
9R
7
6
6
7

STEP 4 Top Frame Assembly
7
1. Attach TOP FRAME (5) to the UPRIGHT
(6) using two 1/2" X 3" HEX BOLTS
(23), four 1/2" LARGER WASHERS
(32), and two 1/2" NYLON NUTS (36).
2. Attach LOGO PANEL (3)
to the UPRIGHT (6) using
four 1/2" X 3-1/8" HEX
BOLT (22), eight 1/2"
SMALL WASHERS (33),
four 1/2" NYLON NUTS
(36), two 5/16" X 1/2"
INNER HEX SCREWS
(27), and two 5/16"
WASHERS (35).
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
This step requires three people!
22
27
27
22
33
33
3
35
31
33
33
36
23
32 36
36
33
5
7
6
7
6
36 31
32 23
33
35
33
33

1. Attch OLMPIC BAR (4) to the VERTICAL BEARING HOUSING
(11) using eight 3/8" X 1-1/4" HEX BOLTS (26), sixteen 3/8"
WASHERS (34), and four 3/8" NYLON NUTS (37).
8
STEP 5 Olympic Bar Assembly
26
26
26
34
34
34
34
37 37
11
26
34
34
4
34
37
37
11
34
4
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)