Body Craft Option User manual

QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or
find missing or damaged parts, we will guarantee your complete satisfaction through our authorized
dealer service centers or our home office customer service department. Please call your local dealer for
assistance or RSI at 800-990-5556 (9:00 AM - 5:00 PM). Our trained techanicians will provide immediate
assistance to you, free of charge.
We stand behind our products. Every piece, every part of this BODYCRAFT strength training system is
guranteed for as long as you own it. We will repair or replace anything that goes wrong.
Bodycraft is a division of Recreation Supply Inc.
P. O. Box 181
Sunbury, OH 43074
INSTRUCTION MANUAL
OPTION OF X PRESS
LEG PRESS (NEW MODEL)

-1-
BEFORE YOU BEGIN
Congratulations and thank you gor selecting the BODYCRAFT LEG PRESS Ⅱ
strength training system. The BODYCRAFT LEG PRESS Ⅱoffers an
impressive array of strength training exercises to develop every major muscle
group of the body. Whether your goal is cardiovascular fitness, a shapely, toned
body or dramatic muscle size and strength, the BODYCRAFT LEG PRESS Ⅱ
will help you achieve the specific results you want.
For your safety and benefit, read this manual and the accompanying literature
before using the BODYCRAFT LEG PRESS Ⅱ. Keep this manual for future �
reference. If you have additional questions, please call your local BODYCRAFT �
dealer or our customer service department at 800-990-5556 Monday through �
Friday, 9 a.m. until 5 p.m. Eastern Time.
IMPORTANT SAFETY NOTES
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with pre-existing health problems. Recreation Supply, Inc. assumes no
responsibility for personal injury or property damage sustained by or
through use of this product.
1. This product must be assembled on a flat, level surface to assure its
proper function.
2. Clean pads and frame on a regular basis. We recommend warm,
soapy water. Do not use harsh or abrasive chemicals.
3. Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4. Keep children away from the BODYCRAFT LEG PRESS Ⅱat all times.
5. Keep your hands away from cables and pulleys during operation.
Keep your hands away from moving parts other than the designated
handles.
6. When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
7. Make certain all cables are seated within the pulleys before every use.
8. Exercise with care to avoid injury.
9. If unsure about the proper use of the BODYCRAFT LEG PRESS Ⅱstrength�
training system call your local BODYCRAFT dealer or our customer
service department at 800-990-5556.

EXPLODED VIEW
236
206
236
237
233
228
228
235
241
241
203
223
222
238
211
217
218
224
225
234
241
202
238
212
212
213
219
219
238
238
234
238
241
238
214
207 238
238
238
238
238
229
205
229
223
204
229
230
238
230
241
241
242
230
238
228
231
237
237
239
241
239
240
233
241
216
219
219
213
213
219
219
210
209
216
216
236
208
236
226
226
221
236
239
236
226
227
227
237
237
201
215
215
240
237
240
221
241
233
232
220 218
221
221
221
-2-

PARTS CHART
NO. DESCRIPTION QTY.
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
1
1
1
1
1
1
1
1
1
1
1
2
3
1
2
3
1
2
6
1
5
1
2
1
1
3
2
4
4
4
1
1
3
4
1
6
14
21
3
8
12
1
1
BASE STABILIZER
LEG PRESS MAIN FRAME
LEFT LEG PRESS HANDLE
RIGHT LEG PRESS HANDLE
LONG LEG PRESS CONNECTOR
FRONT LEG PRESS SUPPORT
WEIGHT BASE CONNECTOR
REAR LEG PRESS SUPPORT
FOOT PLATE CONNECTOR
FOOT PLATE
BACK PAD ADJUSTER
BEARING HOUSING(all pre-assembled)
LEG PRESS AXLE
45mm X 75mm RECT. CAP
50mm SQ. CAP
45mm X 75mm RECT. PLUG
45mm SQ. PLUG
SPACER
25.4mm STEEL BUSHING(all pre-assembled)
LOCKING SPRING KNOB
PULLEY
LEG PRESS STOPPER
1" X 200mm HAND GRIP(all pre-assembled)
BACK PAD FOR LEG PRESS
SEAT PAD FOR LEG PRESS
5/8" X 6-1/2" HEX BOLT
1/2" X 3-1/4" HEX BOLT
1/2" X 1-3/4" HEX BOLT
3/8" X 4" HEX BOLT
3/8" X 3-1/8" HEX BOLT
3/8" X 2-3/4" HEX THREADED BOLT
3/8" X 2-3/4" HEX BOLT
3/8" X 1-3/4" HEX BOLT
3/8" X 1" HEX THREADED BOLT
3/8" X 5/8" SET SCREW(all pre-assembled)
5/8" WASHER
1/2" WASHER
3/8" WASHER
5/8" NYLON NUT
1/2" NYLON NUT
3/8" NYLON NUT
50 SQ. END PLUG
LEG PRESS CABLE
201
205
202
204
207
206
203
211 212 213
208 209
210
217215 216214 218 220219
223222221
225
224
226
227
228
229
230
231
232
233
234
239
240
241
242
236
237
238
235
243
0
(inch) 1" 2" 3"1/21/4 3/4 1/2 1/2 4" 5" 6"1/2 1/2 1/2
-3-

88
101 241
230
230
238
1
238
205
238
207
1. Attach the Weight Base Connector (207) to the Base Frame (1) using two 3/8" X 3-
1/8" Hex Bolts (230), four 3/8" Washers (238) and two 3/8" Nylon Nuts (241). Look
for the sticker on the Weight Base Connector (207) to determine the correct
orientation.
2. Attach the Long Leg Press Connector (205) to the Base Frame (1) using the
existing two 3/8" X 3-1/8" Hex Head Bolts (88) and two 3/8" Washers (101) used to
assemble the Cable Arm Assembly to the Xpress Base Frame. Remove the Nylon
Nuts and discard. Thread the bolts into the threaded holes in the Long Leg Press
Connector (205).
STEP 1
-4-
242

1. Attach the Leg Press Main Frame (202) to the Weight Base Connector (207) and
the Long Leg Press Connector (205) using four 3/8" X 4" Hex Bolts (229), eight
3/8" Washers (238) and four 3/8" Nylon Nuts (241).
2. Attach the Base Stabilizer (201) to the Leg Press Main Frame (202) using two
1/2" X 3-1/4" Hex Bolts (227), four 1/2" Washers (237) and two 1/2" Nylon Nuts
(240). Attach a 45mm X 75mm Rect. Cap (214) to the bottom rear of the Leg
Press Main Frame (202). Attach a 50 mm Sq. Caps (215) to each end of the
Base Stabilizer (201).
3. Slide a Bearing Housing (212) onto each end of the welded axle on the Rear Leg
Press Support (208) and then bolt the Bearing Housings (212) to the Leg Press
Main Frame (202) using four 1/2¨ X 1-3/4¨ Hex Bolts (228), eight 1/2¨ Washers
(237) and two 1/2¨ Nuts (240).
4. Attach the Front Leg Press Support (206) to the Leg Press Main Frame (202)
using one 5/8" X 6-1/2" Hex Bolt (226), two 5/8" Washers (236) and one 5/8"
Nylon Nut (239).
5. Attach the Foot Plate Connector (209) to the Rear Leg Press Support (208) and
the Front Leg Press Support (206) using one 5/8" X 6-1/2" Hex Bolt (226), two
5/8" Washers (236) and one 5/8" Nylon Nut in each Leg Press Support.
6. Attach the Foot Plate (210) to the Foot Plate Connector (209) using two 1/2"
Washers (237) and two 1/2" Nylon Nuts (240). Attach two 45mm X 75mm Rect.
Plugs (216) to the Foot Plate (210).
7. Attach the Right and Left Leg Press Handles (203 & 204) to the Leg Press Main
Frame (202), angle facing up, using two 3/8" X 3-1/8" Hex Bolts (230), four 3/8"
Washers (238) and two 3/8" Nylon Nuts (241).
8. Attach the Seat Pad for Leg Press (225) to the Leg Press Main Frame (202) using
two 3/8" X 1" Hex Bolts (234), one 3/8" X 2-3/4" Hex Bolt (231) and three 3/8"
Washers (238). Attach the Back Pad for Leg Press (224) to the Back Pad
Adjuster (211) using two 3/8" Washers (238) and two 3/8" X 1" Hex Bolts (234).
Screw the Locking Spring Knob (220) into the Leg Press Main Frame (202) and
the slide the Back Pad Adjuster (211) into the Main Frame. Adjust to the desired
position by pulling the Locking Spring Knob (220).
Tighten all bolts gradually, from ground - up.
STEP 2
-5-

218
218
229
205
229
238
238
226
206 208
226
240
237
238
234
211
217
224
236239 238
230
209 210
220
214
203
216
216
204
236
236
216
227
207
240
212
228
237
237
215
215
201
239
238
238
234
202
231
241
238
241
238
241
236
240
STEP 2
-6-
225

STEP 3
LEG PRESS CABLE (243)
bolt end metal ball end
-7-
1. Screw the threaded end (approximately half way) of the Leg Press Cable
(243) into the Single Pulley Block (27) as shown in Fig. 1.
2. Route the cable up and over the right side pulley in the Top Frame (5) as
shown in Fig. 2. Mount the pulley using one 3/8" X 2-3/4" Hex Bolt (89) and
one 3/8" Nylon Nut (107).
3. Continue to route the cable down to the pulley on the Base Frame (1) as
shown in Fig. 3. Mount the pulley using one 3/8" X 1-3/4" Bolt (91) and one
3/8" Nut (107).
4. Then route the cable up to the lower pulley in the Adjustable Pulley Block (25)
as shown in figure 4. Attach the pulley to the second hole from bottom. The
multiple holes are for cable adjustment. When cabling is complete, this pulley
can be moved upward to take up slack, or downward to gain length.
5. Continue to route the cable down to the pulley on the Base Frame (1) just
behind the weight stack, as shown in Fig. 5. Mount the pulley using one 3/8"
X 1-3/4" Bolt (91) and one 3/8" Nut (107).
6. Continue to route the cable underneath the weight stack and around the
horizontally mounted pulley on the Leg Press Main Frame (202). Mount the
pulley using one 3/8" X 1-3/4" Bolt (233) and one 3/8" Nut (241) as shown in
Fig. 6.
7. Continue to route the cable through the slot in Leg Press Main Frame (202),
and under and around (exiting on the top) the lowest pulley on the Rear Leg
Press Support (208) as shown in Fig. 7, Step 1. Mount the pulley using one
3/8" X 1-3/4" Bolt (233) and one 3/8" Nut (241).
8. Then route the cable under and around (exiting on the top) the right side (as if
sitting on seat) pulley mounted in Leg Press Main Frame (202) as shown in
Fig 7. Mount two pulleys here using one 3/8" X 2-3/4" Hex Bolt (232) and one
3/8" Nylon Nuts (241).
9. Route the cable in the same manner under and around the uppermost pulley
mounted on the Rear Leg Press Support (208) as shown in Fig. 7, Step 2.
Mount the pulley using one 3/8" X 1-3/4" Bolt (233) and one 3/8" Nut (241).
10. Route the cable in the same manner under and around the left side (as if
sitting on seat) pulley mounted in Leg Press Main Frame (202) as shown in
Fig 7.
11. Hook the ball end of the cable into the receptor on the Rear Leg Press
Support (208) as shown in Fig. 8.
Hint: When viewed from the side, the Leg Press Cable should be a series
of "loops". There should not be any "X's".

STEP 3
FIG 7
STP 2
FIG 8
243
FIG 2
FIG 1
FIG 4
FIG 3
FIG 5
FIG 6
FIG 7
FIG 8
FIG 4
91
25
61
107
243
FIG 3
91
61
107
243
243
FIG 6
233
221
241 243
202
FIG 7 STP 1
202
208
FIG 7
241
232
221
243
27
61
91
107
FIG 1
61
61
89
107
FIG 2
243
FIG 5
61
91
107
LEG PRESS CABLE (243)
bolt end metal ball end
-8-

1.Make certain all bolts are tightened securely.
2.Make certain all cables are seated into all pulley grooves. A cable
rubbingagainst steel will peel the nylon coating, voiding warranty and
resulting in a need for replacement.
3.Pre-stretch the cables. Pull on the cables with great force, helping remove
any kinks and providing any initial cable stretch.
4.Be aware the cables can loosen and slightly stretch upon initial use.
5.For better performance, apply a household lubricant (such as silicone) to
any adjustable areas.
6.Enjoy many years of a Fit Lifestyle.
Thank you for purchasing the BodyCraft LEG PRESS Ⅱ. If You have
any questions, please call your local BodyCraft dealer or call our
customer service department at 800-990-5556
Assembly is complete! Please take the following steps before using the gym:
-9-