BOMBAY 4100184 User manual

4100184
Statesmen’s Terrarium
Page 1 of 4 R1-11-25-03
Parts and Hardware List
A. Cage Assembly 1 pc
B. Legs 4 pcs
C. Brass Mantle 1 pc
D. Top Frame 1 pc
E. Glass Holder 1 pc
F. Glass Panels 4 pcs
G. Metal Tray 1 pc
H. Brass Handles 4 pcs
I. Allen Head Bolts 8 pcs
J. Lock Washers 8 pcs
K. Flat Washers 8 pcs
L. Phillips Head Screws 4 pcs
M. Phillips Head Screwdriver 1 pc
N. Allen Head Wrench 1 pc
∗Please make sure that you have all the parts and hardware indicated above before you begin assembly of this item.
∗Use the hardware illustrations to determine correct piece and size.
∗This item should be assembled on a soft surface to prevent scratching the finish during assembly.
∗ This item may require periodic tightening.
Hardware Illustrations
I. Allen Head Bolt J. Lock Washer
K. Flat Washer L. Phillips Head Screw

4100184
Statesmen’s Terrarium
Page 2 of 4 R1-11-25-03
Attach Legs
Parts required
A. Cage Assembly 1 pc J. Lock Washers 8 pcs
B. Legs 4 pcs K. Flat Washers 8 pcs
I. Allen Head Bolts 8 pcs N. Allen Head Wrench 1 pc
1. Attach Legs (B) Put the Cage Assembly (A) upside down on a soft surface. Align the pre-threaded holes in the Legs
(B) with the pre-drilled holes in the corner blocks of Cage Assembly (A). Secure with Allen Head Bolts (I), Lock
Washers (J) and Flat Washers (K) using Allen Head Wrench (N). See Illustration #1
Illustration #1

4100184
Statesmen’s Terrarium
Page 3 of 4 R1-11-25-03
Attach Metal Tray & Glass Panels
Parts required
A. Cage Assembly 1 pc F. Glass Panels 4 pcs
E. Glass Holder 1 pc G. Metal Tray 1 pc
2. Attach Metal Tray (G) Put the Cage Assembly (A) upright. Put the Metal Tray (G) into the Cage Assembly (A).
See Illustration #2
3. Attach Glass Panels (F) Put the Glass Panels (F) into the pre-drilled groove inside Cage Assembly (A). See
Illustration #2
Illustration #2

4100184
Statesmen’s Terrarium
Page 4 of 4 R1-11-25-03
Attach Top Frame, Brass Mantle & Glass Holder
Parts required
C. Brass Mantle 1 pc H. Brass Handles 4 pcs
D. Top Frame 1 pc L. Phillips Head Screws 4 pcs
E. Glass Holder 1 pc M. Phillips Head Screwdriver 1 pc
4. Attach Glass Holder (E) Align the pre-drilled holes in the Glass Holder (E) with pre-drilled holes in the
Cage Assembly (A). Be sure that the edges of Glass Panels (F) align with the pre-drilled groove of Glass
Holder (E). Secure with Phillips Head Screws (L) using Phillips Head Screwdriver (M). See Illustration #3.
5. Attach Top Frame (D)Align the pre-drilled holes in the Top Frame (D) with the pre-threaded holes in the Glass
Holder (E). Secure with Brass Handles (H) turning in a clockwise direction. See Illustration #3.
6. Put the Brass Mantle (C) on the glass of Top Frame (D) carefully. See Illustration #3.
Illustration #3