Bosch Doro Secure 680 User manual

Doro Secure 680 - Telecare functions
CRS-DORO-680 | F.01U.282.198 | V1.1 | 2013.07
en User Guide

Doro Secure 680 Introduction | en 3
Bosch Security Systems User Guide F.01U.282.198 | V1.1 | 2013.07
1 Introduction
Scope of the user guide
This user guide only describes the telecare functions of the
Doro Secure 680. The full version of the user manual is available
at the following address: www.doro.co.uk/Support/
NOTICE!
The services described in this user guide are only supporting
functions that might not always be available:
– The GSM network, therefore the voice and GPRS data,
might not always be available.
– Be aware that depending on the circumstances, the GPS
locating can take some time. The inavailability of a GPS
signal might cause the GPS locating to not always work.
– The battery capacity of the Doro Secure 680 is limited.
Make sure that the battery is always charged if assistance
is needed. When using the GPS locating, charge the
battery at least every 2 days.
– The user of the Doro Secure 680 might not be properly
identified, if the SIM card is replaced.
– To avoid unwanted roaming costs please change the
default setup in the Doro Secure 680. Go to Settings -
General - Network setup - Network mode: change to Manual.

4en | Operating the Doro Secure 680 Doro Secure 680
F.01U.282.198 | V1.1 | 2013.07 User Guide Bosch Security Systems
2 Operating the Doro Secure 680
2.1 Telecare functions overview
1. Assistance call
2. End call / Power on-off
3. Call button
4. Amber Alert
5. Position per button
2.2 Make an assistance call
If you require help, press the Assistance call button on the
back of your Doro Secure 680 to initiate an assistance call:
If available, GPS locating and alarm information are sent to the
alarm receiving centre. The call is answered by an operator.
ABC
DEF
ABC
GHI JKL MNO
WXYZTUVPQRS
0
8
456
79
123

Doro Secure 680 Operating the Doro Secure 680 | en 5
Bosch Security Systems User Guide F.01U.282.198 | V1.1 | 2013.07
2.3 Cancel an assistance call
If you have pressed the assistance call button by mistake, you
can cancel the call by pressing the End call button.
2.4 Are you OK?
The Doro Secure 680 has a built-in activity monitor, which
ensures that an assistance call is made automatically if no
answer is given within a preset period of time.
At a preset time of the day (configured by the monitoring
center), the message "Are you OK?" appears on the display of
the Doro Secure 680. The phone vibrates and plays a sound.
1. Press yes, using the left / right selection buttons to
confirm that no help is necessary. The phone returns to
standby.
Press no to confirm that help is needed.
If you have answered no, the Doro Secure 680 displays the
message "Do you need help?" . Depending on the settings,
the phone also vibrates and plays a sound.
2. Press no to confirm that no help is necessary. The phone
returns to standby.
Press yes to confirm that help is necessary.
If you have answered yes, an assistance call to the alarm
receiving center is started.
NOTICE!
If you do not answer all these questions within a preset period
of time, an assistance call to the alarm receiving centre is
automatically started.

6en | Operating the Doro Secure 680 Doro Secure 680
F.01U.282.198 | V1.1 | 2013.07 User Guide Bosch Security Systems
2.5 Position per Button
The last available GPS position can be sent upon request to the
alarm receiving centre.
1. Press button B.
2. The Doro Secure 680 displays the message "Sending
position" and an hour glass is shortly displayed.
3. If the satellite icon is visible on Doro Secure 680 display,
the current GPS location is sent.
2.6 Amber Alert
The Doro Secure 680 has a special function Amber Alert,
designed to monitor dangerous situations. If, within a preset
period of time the Amber Alert is not cancelled, then an
assistance call to the alarm receiving center is automatically
started.
1. Press button Ato activate and start the Amber alert.
A message "Amber Alert activated" is shortly displayed.
2. A preset count-down timer is started. During this time, the
Doro Secure 680 displays the following status symbol:
If the user has not deactivated the Amber Alert by
pressing button Aon the device within a predefined period
of time, the Doro Secure 680 displays the message:
"10 seconds before the alert. Cancel? "
Depending on the settings, the phone also vibrates and
plays a beep sound.
NOTICE!
If you do not cancel the Amber Alert within 10 seconds or do
not answer, an assistance call to the alarm receiving center is
automatically started.

Bosch Security Systems
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Security Systems, 2013