Bosch D9412GV4 User manual

en Installation and System Reference Guide
Control Panels
D9412GV4/D7412GV4 v2.03

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | Certifications and Approvals
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 2
Certifications and Approvals
The D9412GV4/D7412GV4 v2.03 Literature Pack
includes an Approved Applications chapter in this guide.
Refer to this chapter for additional guidelines on
installing the control panels in Underwriters
Laboratories Inc. (UL) and fire-specific applications.
Listings and Approvals
UL
The D9412GV4 and D7412GV4 are listed as UL 864
Commercial Fire control panels. The D9412GV4 and
D7412GV4 are also UL Listed for Central Station,
Local, Auxiliary, Proprietary, and Household Fire Alarm,
and Central Station, Local, Police Station Connect,
Holdup, Household Burglar Alarm and Encrypted line
Security when communicating via a network.
cUL
The D9412GV4 and D7412GV4 are cUL listed for Local
Burglar Alarms, Signal Receiving Centre and Premise
Alarm, Residential Fire, Household Burglar, Propriety
Burglar, and Digital Apparatus.
Department of Defense (DOD)
The D9412GV4/D7412GV4 was granted approval for
Department of Defense (DoD) installations in Sensitive
Compartmented Information Facilities (SCIF).
Federal Communications Commission
(FCC) Rules
Part 15
This equipment was tested and found to comply with
the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy; and if not installed and used
according to the instructions, can cause harmful
interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the
user is required to correct the interference at his or
her own expense.
Part 68
This equipment complies with Part 68 of FCC rules. A
label contains, among other information, the FCC
registration number and ringer equivalence number
(REN). If requested, this information must be provided
to the telephone company.
The D9412GV4 and D7412GV4 Control Panels are
registered for connection to the public telephone
network using an RJ38X or RJ31X jack.
The REN is used to determine the number of devices
that can be connected to the telephone line. Excessive
RENs on the telephone line may result in the devices
not ringing in response to an incoming call. In most,
but not all areas, the sum of the RENs should not
exceed five. To be certain of the number of devices
that may be connected to the line, as determined by
the RENs, contact the telephone company to
determine the maximum REN for the calling area.
If you experience trouble with the control panel, please
contact Bosch Security Systems Customer Service for
repair and warranty information. If the trouble is
causing harm to the telephone network, the telephone
company might request that the equipment be
removed from the network until the problem is
resolved. User repairs must not be made, and doing so
will void the user’s warranty.
If the D9412GV4 or D7412GV4 Control Panels causes
harm to the telephone network, the telephone
company attempts to notify you in advance. If advance
notice is not practical, the telephone company notifies
you as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company might make changes in its
facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this
happens, the telephone company provides advance
notice in order for the necessary modifications to be
made, resulting in uninterrupted service.
This equipment cannot be used on public coin service
provided by the telephone company. Connection to
Party Line service is subject to state tariffs. (Contact
your state public utilities commission for information.)
FCC Registration Number: US:ESVOT00BD9412GV3
Service Center in USA:
Bosch ST Service Center
8601 East Cornhusker Hwy
Dock B
Lincoln, NE 68507 - 9702 USA
Ringer Equivalence: 0.0B

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | Contents
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 3
Contents
Federal Communications Commission (FCC)
Rules ........................................................ 2
1.0 Introduction............................................. 7
1.1 About documentation .............................. 7
2.0 Lightning Strikes....................................10
2.1 Effects....................................................10
2.2 Precautions during Installation.............. 10
3.0 Overview................................................ 11
3.1 Configuration and Parts.........................11
3.1.1 Parts List ...............................................12
3.1.2 Parts Available by Separate Order......... 12
3.2 Accessories............................................13
3.3 Features in the GV4 Series Control Panels
............................................................... 16
3.3.1 SDI Interconnect Wiring ........................16
3.3.2 Tip and Ring Posts.................................16
3.3.3 Telephone Line Sniff.............................. 16
3.3.4 Points .................................................... 16
3.3.5 Areas and Accounts ...............................16
3.3.6 Digital Communicator............................17
3.3.7 Keypads ................................................. 17
3.3.8 Keyswitch .............................................. 18
3.3.9 Access Control.......................................18
3.3.10 Event Memory........................................18
3.3.11 Event Log............................................... 18
3.3.12 Ground Fault Detection ......................... 18
3.3.13 Ground Fault Detection Added Feature 19
3.3.14 Conettix Functions ................................ 19
3.3.15 Programming .........................................19
3.3.16 Dual Authentication ...............................19
3.3.17 Other Features ......................................19
4.0 Installation............................................. 20
4.1 Installation Preparation ......................... 20
4.2 Enclosure Options .................................20
4.3 Mounting Enclosure............................... 20
4.4 Installing the Control Panel ................... 21
4.5 Connecting Earth Ground...................... 21
4.5.1 Terminal 10............................................ 21
4.5.2 Ground Fault Detect Enable .................. 21
4.5.3 Enabling Ground Fault Detection .......... 21
4.5.4 Ground Fault Specifications ..................21
4.5.5 Locking the Reset Pin............................ 22
4.6 Completing the Installation ................... 22
4.6.1 Charging the Battery..............................22
4.6.2 Installing and Wiring Detection Devices 23
4.6.3 Installing Modules and Outputs ............ 23
4.6.4 Connecting the On-board Points and
Keypads ................................................. 23
4.6.5 Powering Up .......................................... 23
4.7 Updating Control Panel Firmware ......... 23
4.8 Programming the Control Panel ............ 23
4.9 Installing the Point Chart Label............. 23
4.10 Testing the System................................ 23
4.11 Service Walk Test .................................. 24
5.0 Power Supply ........................................ 28
5.1 Primary Power Terminals 1 and 2 ......... 28
5.1.1 Primary (AC) Power Circuit................... 28
5.1.2 Installing the Transformer ..................... 28
5.2 Secondary Power Terminals.................. 28
5.2.1 Secondary (DC) Power.......................... 28
5.2.2 Installing the Battery ............................. 29
5.2.3 Replacing the Battery ............................ 30
5.2.4 Battery Supervision ............................... 31
5.2.5 Battery Charging Circuit Float Charge .. 31
5.2.6 Battery Discharge and Recharge Schedule
.............................................................. 32
6.0 Power Outputs ...................................... 34
6.1 Circuit Protection .................................. 34
6.2 Total Available Power ............................ 34
6.3 Continuous Power Outputs................... 34
6.4 Programmable Power Outputs.............. 35
6.4.1 Programming ......................................... 35
6.4.2 Terminals 6 and 7.................................. 35
6.4.3 Fire System Power Formula .................. 35
6.4.4 Terminal 8.............................................. 35
7.0 Telephone Connections......................... 37
7.1 Registration ........................................... 37
7.2 Notification............................................ 37
7.3 Location................................................. 37
7.4 Telephone Cord Connection ................. 37
7.5 Phone LED (Red)................................... 38
7.6 Operation Monitor LED (Green)............ 38
7.7 Dialing Format ....................................... 38
7.8 Telephone Line Monitor ........................ 38
7.9 Called Party Disconnect ........................ 39
7.10 Communication Failure ......................... 39
7.11 D928 Dual Phone Line Switcher............ 39
7.11.1 Description............................................ 39
7.11.2 Operation .............................................. 39
7.11.3 Installing the D928 ................................ 41
7.11.4 D928 Status LEDs ................................. 41
8.0 On-Board Points .................................... 42

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | Contents
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 4
8.1 Terminals 11 to 22 Description ............. 42
8.2 Point Sensor Loops ............................... 42
8.3 Point Parameters ...................................42
8.4 Point Response Time............................. 43
8.5 Wiring Information for Installations Using
the Rothenbuhler 5110/4001-42 High
Security Bell ..........................................43
9.0 Off-Board Points.................................... 46
9.1 Zonex Buses ..........................................46
9.1.1 POPIT Modules ......................................46
9.1.2 POPEX Modules..................................... 46
9.1.3 Missing Conditions ................................ 46
9.1.4 Control Panel Responses to Missing Point
Conditions .............................................46
9.2 D8125 and D9127 POPIT Modules ........46
9.3 Installing the D8125 POPEX Module ..... 48
9.3.1 Mounting................................................48
9.3.2 Wiring the D8125 to the Control Panel .48
9.3.3 Wiring POPITs to the Data Expansion
Loop ......................................................49
9.3.4 Wiring Data Expansion Loops to POPEX
Modules .................................................49
9.3.5 POPIT Sensor Loops.............................. 50
9.3.6 POPIT Module Point Assignments ......... 50
9.3.7 Program Record Sheet ..........................50
9.3.8 POPIT Labels ......................................... 50
9.4 D8128D OctoPOPIT Module ..................51
9.4.1 Description ............................................51
9.4.2 Listings .................................................. 51
9.4.3 Installation.............................................52
9.4.4 Setting the OctoPOPIT Switches...........52
9.4.5 Mounting OctoPOPITs ........................... 53
9.4.6 Wiring OctoPOPITs ................................ 53
9.4.7 OctoPOPIT Sensor Loops......................57
9.5 Testing Off-Board Points .......................58
9.6 SDI2 Octo-input Point Modules............. 58
9.7 Extra Point Events .................................58
10.0 Off-Board Outputs ..................................... 60
10.1 D8129 OctoRelay................................... 60
10.1.1 Configuring the D8129 OctoRelay ......... 62
10.1.2 Relay Outputs ........................................62
10.1.3 Installation............................................. 62
10.1.4 Wiring Connections ............................... 62
10.2 D811 Arm Status Relay Module ............. 63
10.2.1 Relay Output.......................................... 63
10.2.2 Installation............................................. 63
10.2.3 Wiring Connections ............................... 63
10.3 SDI2 Octo-output Relay Modules .......... 63
11.0 Arming Devices.......................................... 65
11.1 Description............................................ 65
11.2 SDI/SDI2 Bus Terminals 29 to 36.......... 65
11.2.1 Shortcuts and Custom Functions.......... 65
11.2.2 Assigning an Address for the Keypad .... 66
11.2.3 Installation............................................. 66
11.3 D279A Independent Zone Control......... 67
11.4 Keyswitch .............................................. 68
11.4.1 Description............................................ 68
11.4.2 Programming ......................................... 68
11.4.3 Installation............................................. 68
11.4.4 Operation .............................................. 68
12.0 SDI Devices ............................................... 69
12.1 Description............................................ 69
12.2 Installation............................................. 69
12.2.1 Open Wire Trouble on SDI .................... 69
12.3 D9210C Access Control Interface Module
.............................................................. 69
12.3.1 Access ................................................... 69
12.3.2 Switch Settings ..................................... 69
12.4 SDI Addresses 88 and 92 ...................... 70
12.4.1 Local RPS Programming........................ 70
12.5 SDI Network Interface Modules ............ 70
12.5.1 Address Settings ................................... 71
12.5.2 Supervision............................................ 71
13.0 SDI2 Devices ............................................. 72
13.1 Description............................................ 72
13.2 Installation............................................. 72
13.2.1 Open Wire Trouble on SDI2 .................. 72
13.3 B208 Octo-input Module ....................... 72
13.3.1 Address Settings ................................... 72
13.3.2 Supervision............................................ 73
13.4 B308 Octo-output Module..................... 73
13.4.1 Address Settings ................................... 73
13.4.2 Supervision
............................................ 74
13.5 B450 Plug-in Communicator Interface .. 74
13.5.1 Address Settings ................................... 74
control panel uses the address for
communications. ................................... 74
13.6 B426 Ethernet Communication Module 75
13.6.1 Address and Emulation Settings ........... 75
13.6.2 Supervision............................................ 75
13.6.3 Local RPS Programming........................ 76
13.6.4 Ethernet Communications Module Faults
.............................................................. 76
13.7 B420 Ethernet Communication Module 76

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | Contents
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 5
13.7.1 Address and Emulation Settings............76
13.7.2 Supervision............................................ 76
13.7.2 Local RPS Programming ........................ 77
13.7.3 Ethernet Communications Module Faults
............................................................... 77
13.8 B520 Auxiliary Power Supply Module....77
13.8.1 Address Settings ................................... 77
13.8.2 Supervision............................................ 78
13.8.3 Auxiliary Power Supply Faults ............... 78
13.9 B810 wireless receiver .......................... 78
13.9.1 Supervision............................................ 78
13.9.2 Wireless Receiver Faults........................78
13.9.3 Wireless Repeater Faults........................ 78
13.10 B820 SDI2 Inovonics Interface Module . 79
13.10.1
Supervision…..…………………………………79
13.10.2 Wireless Receiver Faults....................... 79
13.10.3 Wireless Repeater Faults.....................79
13.11 B915 Basic Keypad ................................ 79
13.12 B920 Two-line Alphanumeric Keypad .... 79
13.13 B921C Two-line Capacitive Keypad with
Inputs.....................................................79
13.14 B930 ATM Style Alphanumeric Keypad..80
13.15 B942/B942W Touch Screen Keypad......80
14.0 Accessory Connector.................................81
15.0 Faceplates ................................................. 82
15.1 D9412GV4/D7412GV4 v2.00 (and higher)
Faceplate ...............................................82
16.0 Specifications ............................................83
16.1 Control Panel Power Supply.................. 83
16.2 B520 Power Supply ...............................85
16.3 Control panel Terminal Wiring............... 86
17.0 Approved Applications...............................88
17.1 Optional Compatible Equipment ........... 88
17.2 Burglary Applications............................. 88
17.3 Bank Safe and Vault Applications..........88
17.3.1 Control Panel Enclosure Requirements. 88
17.3.2 Battery Connections..............................88
17.3.3 Bell Requirements ................................. 88
17.3.4 System Configuration Requirements.....89
17.3.5 Exit Delay............................................... 89
17.3.6 Equipment Requirements ...................... 89
17.4 Fire Applications.................................... 89
17.4.1 Four-Wire Smoke Detectors .................. 90
17.4.2 Two-Wire Smoke Detectors................... 91
17.4.3 Two-Wire Smoke Detector Specifications
............................................................... 91
17.4.4 NFPA Style A (Class “B”) Circuit ........... 91
17.4.5 Other Devices........................................ 92
17.4.6 UL Listed Two-Wire Smoke Detectors
Compatible with the D125B.................. 93
17.4.7 UL Listed Synchronization (Sync)
Modules and Strobes Compatible with the
D9412GV4/D7412GV4........................... 94
17.5 Enclosures............................................. 99
17.5.1 D8103 Enclosure ................................... 99
17.5.2 D8108A Enclosure ................................. 99
17.5.3 D8109 Red Fire Enclosure..................... 99
18.0 Installer Menu.......................................... 104
Characters....................................................... 107
B91x/B92x....................................................... 107
(*, C [3-sec pause], D [Dial Tone Detect])...... 107
choose the character shown. .......................... 107
Network address characters ........................... 107
Use the [0] key to enter a period or dash. ...... 107
18.1 [1] Program Menu ............................... 108
18.1.1 [1] Reporting > [1] Phone Menu
Parameters .......................................... 108
18.1.2 [1] Reporting > [2] Network Menu
Parameters .......................................... 109
18.1.3 [1] Reporting > [3] Routing Menu
Parameters .......................................... 112
18.1.4 [2] Network > [1] Bus Module (1) or [2]
Bus Module (2) Module Parameters.... 114
18.1.5 [2] Network > [1] Bus Module (1) or [2]
Bus Module (2) > [2] Address Parameters
............................................................ 116
18.1.6 [2] Network > [1] Bus Module (1) or [2]
Bus Module (2) > [3] DNS Parameters 117
18.1.7 [2] Network > [3] Cellular (common)
Menu Parameters ................................ 119
18.1.8 [3] RPS > [1] RPS Passcode Menu
Parameters .......................................... 120
18.1.9 [3] RPS > [2] RPS Phone Number Menu
Parameters .......................................... 121
18.1.10 [3] RPS > [3] RPS IP
Address Menu Parameters .................. 122
18.1.11 [3] RPS > [4] RPS Port Number Menu
Parameters .......................................... 122
18.1.12 [4] Area Options Menu Parameters ... 123
18.1.13 [5] Keypad > [1] Scope Menu Parameters
............................................................ 125
18.1.14 [6] Users Menu Parameters ............... 126
18.1.15 [7] Points Menu Parameters .............. 128

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | Contents
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 6
18.1.16 [8] Disable Programming Menu
Parameters ..........................................135
18.2 [2] Wireless Menu ............................... 136
18.2.1 [1] Points > [1] Enroll Point RFID Menu
Parameters ..........................................136
18.2.2 [1] Points > [2] Replace Point RFID Menu
Parameters ..........................................137
18.2.3 [1] Points > [3] Remove Point RFID Menu
Parameters ..........................................137
18.2.4 [2] Repeaters > [1] Add Repeater Menu
Parameters ..........................................138
18.2.5 [2] Repeaters > [2] Replace Repeater
Menu Parameters ................................138
18.2.6 [2] Repeaters > [2] Remove Repeater
Menu Parameters ................................139
18.2.7 [3] Diagnostics > [1] RF Points ............ 139
18.2.8 [3] Diagnostics > [2] RF Repeaters ...... 141
18.3 [3] Diags Menu .................................... 142
18.3.1 [1] Wireless ..........................................142
18.3.2 [2] Network Menu ................................ 142
18.3.3 [3] Cellular Menu.................................. 144
18.4 [4] Srvc Byp Menu............................... 145
18.5 [5] Versions Menu ............................... 146
19.0 UL/NFPA Compliant Installations ....... 147
19.1 Required Components.............................147
19.2 Installing Combination Fire and Intrusion
Alarm Systems ..................................... 147
19.2.1 SDI Bus Devices...................................147
19.2.2 Zonex Bus Devices............................... 147
19.2.3 SDI2 Bus Devices ................................ 148
20.0 Compatible UL Listed Components ... 149
21.0 Current Ratings Charts............................ 151
21.1 D8125MUX .............................................. 151
21.2 Standby Battery Calculations.................. 151
22.0 NFPA 72 Fire Alarm Applications............. 155
22.1 Household Burglary and Commercial
Burglary ............................................... 155
22.2 Bank Safe and Vault ............................ 155
22.3 Standby Battery Calculation................ 155
22.4 Central Station or Local Systems........ 156
22.5 Remote Station or Auxiliary Systems .. 156
22.6 Household Fire Warning Equipment.... 157
22.7 UL 609 ................................................. 157
22.8 UL 365 ................................................. 157
22.9 UL 636 ................................................. 158
22.10ULC S304 Requirements ..................... 158
Appendix A: System Wiring Diagrams .......... 159
A.1Power Supply Side System Wiring ...... 159
A.2Input Points and Peripheral Devices
Wiring Diagrams .................................. 161
A.3SDI and Zonex Devices System Wiring 162
A.4SDI2 Bus Wiring Recommendations.... 165
Appendix B: Point Address Charts ............... 167
B.1Zonex 1 Points..................................... 167
B.2SDI2 Points.......................................... 168

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 1.0 Introduction
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 7
1.0 Introduction
This manual addresses the operation and installation of the D9412GV4/D7412GV4 v2.03 Control
Panels. Throughout this guide, the words “control panel” refer to all control panels (D9412GV4 and
D7412GV4). Table 2 on page 12 provides an overview of the differences in the control panels.
1.1 About documentation
For firmware v2.03
This document contains instructions for a trained installer to properly install, configure, and operate
this control panel, and all optional peripheral devices. Review this document before beginning the
installation to determine the hardware and wiring requirements for the features used.
Throughout this document, the words “control panel” refer to all control panels covered by this
document (D9412GV4/D7412GV4).
Notifications
This document uses Notices, Cautions, and Warnings to draw your attention to important information.
Notice:These include important notes for successful operation and programming of
equipment, or indicate a risk of damage to the equipment or environment.
Caution: These indicate a hazardous situation which, if not avoided, could result in minor or
moderate injury.
Warning: These indicate a hazardous situation which, if not avoided, could result in death or
moderate injury.
Related documentation
To obtain any of the documents listed in this section, download them from the web. Downlaoding
documentation:
1. Go to the Bosch website (us.boschsecurity.com).
2. In the Search text box on the right side of the page, enter the CTN for the product for which you
wish to download the documentation.
3. Press [ENTER].
4. If you see the desired document in the search results, click the link for the document to open it.
Otherwise, click the desired product’s Product Page button. The product page opens with the Details
tab selected.
5. Click on the Documents tab, and then click the desired language listed to the right of the desired
document.
Call Bosch Security Systems, Inc., Technical Support (1-800-289-0096) if you need additional
assistance.

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 1.0 Introduction
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 8
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All
rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered trademarks and must
be treated accordingly.
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems, Inc. web site at
http://www.boschsecurity.com/datecodes.

Table 1: Related Documentation
Product
Type
Name of Documentation Part Number
Control
Panels
Control Panels (D9412GV4/D7412GV4 v2.03) Release Notes F01U287177
Control Panels (D9412GV4/D7412GV4 v2.03) Installation and System Reference
Guide (this document)
F01U265457
UL Certificated Bank Safe and Vault Applications Technogram 73-07302-000
Control Panels (D9412GV4/D7412GV4 v2.03) Program Entry Guide F01U265459
Control Panels (D9412GV4/D7412GV4 v2.03) UL Installation Guide F01U291483
Control Panels (D9412GV4/D7412GV4 v2.00 and higher) Quick Reference Guide F01U265463
Control Panels (D9412GV4/D7412GV4 v2.00 and higher) SIA Quick Reference Guide F01U265466
Keypads Basic Keypad (B915/B915I) Installation Guide F01U297873
Two-line Alphanumeric Keypad (B920) Installation Guide F01U265450
Two-line Capacitive Keypad with Inputs (B921C) Installation Guide F01U285416
ATM Style Alphanumeric Keypad (B930)Installation Guide F01U265451
Touch Screen Keypad (B942) Installation Guide F01U285416
Control Panels (D9412GV4/D7412GV4 v2.0) Control Panel Owner’s Manual F01U287176
Expansion
Devices
Octo-input Module (B208) Installation and Operation Guide F01U265456
Octo-output Module (B308) Installation and Operation Guide F01U265458
RADION receiver SD (B810) Reference Guide F01U261839
SDI2 Inovonics Interface Module (B820) Installation Guide F01U265460
Conettix Plug-in Communicator Interface (B450) Installation and Operation Guide F01U282875
Conettix Ethernet Communication Module (B420) Installation and Operation Guide F01U215236
Conettix Ethernet Communication Module (B426) Installation and Operation Guide F01U266226
Conettix Plug-in Cellular Communicator (B440) Installation and Operation Guide F01U265455
Conettix Plug-in Cellular Communicator (B441) Installation and Operation Guide F01U282233
Conettix Plug-in Cellular Communicator (B442) Installation and Operation Guide F01U283180
Conettix Plug-in Cellular Communicator (B443) Installation and Operation Guide F01U283181
Auxiliary Power Supply Module (B520) Installation and Operation Guide F01U265445
D8128D Installation Guide F01U070537
D8125MUX Operation and Installation Guide F01U034973
ISW-D8125CW-V2 Installation and Operation Guide F01U161691
D9210C Installation and Operation Guide F01U215232

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 1.0 Introduction
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 9
The following image shows an example of a product label and highlights where to find the manufacturing date
within the serial number.


D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 2.0 Lightning Strikes
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 10
2.0 Lightning Strikes
The control panels are designed to significantly
reduce electromagnetic interference and
malfunction generally caused by lightning.
2.1 Effects
Any electronic system can be struck directly by
lightning or be adversely affected by a lightning
strike near the system. When lightning strikes,
several things happen:
An electromagnetic wave spreads from
the point of the strike inducing high
voltages in nearby conductors.
The voltage changes substantially on
electrical grounds near the lightning
strike.
High voltages are induced in anything
directly struck by lightning.
The effects of a lightning strike can include
Missing Trouble, Missing Alarm, or Point Bus
Trouble events. Occasionally, Reboot and
Watchdog events might be sent because the
control panel tried to reset itself.
Electronic systems, including control panels,
cannot be completely immune to direct or
indirect lightning strikes; however, some proven
installation practices might greatly reduce the
risk of undesirable affects.
2.2 Precautions during Installation
To minimize the risk of undesirable effects from
lightning strikes on high risk installations that use
a point-bus technology:
Do not run wiring outside the building.
If you must install the unit in a metal
building, keep the wiring at least 0.61 m
(2 ft) away from external metal surfaces.
Earth ground the unit correctly. Do not
use an electrical ground or telephone
ground.
Avoid running wires near telephone, data,
or power lines inside a building. Historical
evidence shows that locating control
panel wiring at least 0.61 m (2 ft) away
from telephone, data, or power lines is
successful at minimizing lightning
damage. When your data lines must cross
the path of AC or other wiring, cross the
lines perpendicularly.

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 11
3.0 Overview
3.1 Configuration and Parts
Figure 1: System Configuration

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 12
Table 2: Control Panel Comparisons
Features D9412GV4 D7412GV4
Access Control Yes - 8 doors Yes - 2 doors
Number of Arm/Disarm Users 999 399
Number of Cards/Tokens 999 399
Number of Passcode-Protected Custom Functions 16 4
Number of Points 246 75
Number of Off-board Relays 128 64
Number of Areas 32 8
Number of SDI2 Keypads 16 16
Number of SDI Keypads116 16
Number of Phone Lines Supported22 2
Number of B208 Octo-input Modules 24 73
Number of B308 Octo-output Modules 12 64
Number of B420 Ethernet Communication Module 252
5
Number of B426 Ethernet Communication Module 252
5
Number of B450 Plug-in Communicator Interface6252
5
Number of B520 Auxiliary Power Supply Module 8 8
Number of RADION receiver SD (B810)71 1
Number of B820 SDI2 Inovonics Interface Modules 1 1
1 The maximum number of D1260 keypads on the SDI bus is eight.
2On a two phone line system, a D928 Dual Phone Line Switcher is required in order to transmit over a second phone line.
3 For the D7412GV4, only 5 inputs are available on the Octo-input at address 7.
4For the D7412GV4, only 4 outputs are available on the Octo-output at address 6.
5The maximum number of communication devices to be used on the control panel is two on the SDI bus, and two on the SDI2 bus. If
automation is enabled on the SDI bus, an additional module can be added. Of the two devices that can be used on the SDI2 bus both can be
used for reporting / RPS communications or one can be used for reporting / RPS communications and the other can be used for automation.
6Must have a B44x Plug-in Cellular Communicator inserted into the B450 in order for the B450 to be operational.
7Refer to the device-specific installation instructions for each RADION wireless device.
3.1.1 Parts List
The control panels are shipped assembled
from the factory with the following parts:
Literature Pack
7000/9000 Series Point Chart Label
(P/N: 79-06660-000)
Assembly
PC board
Faceplate shield
Mounting skirt
One #6 x 3/4-in screw
3.1.2 Products Available by Separate Order
Order the following products separately to
complete a basic eight-point installation.
B450 Plug-in Communicator Interface
B440 Conettix Plug-in Cellular
Communicator (using 3G)
B441 Conettix Plug-in Cellular
Communicator (using CDMA)
B442 Conettix Plug-in Cellular
Communicator (using GPRS)
The D1260 and D1260B Keypads must
have firmware version 1.04 or higher
for use with the D9412GV4/D7412GV4
Control Panels.

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 13
B443 Conettix Plug-in Cellular
Communicator (using HSPA+)
B520 Auxiliary Power Supply Module
B420, B426 Ethernet Communication
Modules
B915/B915I, B920, B921C, B930, B942,
B942W Keypad
D1255B, D1255, D1260, or D1260B
Keypad
D1255RB Fire Keypad, D1256RB Fire
Keypad, or D1257RB Fire Alarm
Annunciator
D1640 Transformer
D1640-CA Transformer (for Canada)
D1640-SA Transformer (for Saudi
Arabia)
D126 or D1218 Battery
D162 Phone Cord (order two cords if
using the D928 Dual Phone Switcher)
D8103, D8108A, or D8109 Enclosure
Configured packages are also available. Please
consult the Bosch Security Systems, Inc.
Product Catalog.
3.2 Accessories
Refer to the Bosch Security Systems, Inc. product catalog for additional information.
The compatible accessories listed in the table below are specific to the D9412GV4/D7412GV4 with
firmware v2.00 or greater.
Table 3: Compatible Accessories1
Model Title UL
864
UL
985
Intrusion cUL
Intrusion
B208 Octo-input Module X X X X
B308 Octo-output Module X X X X
B420 Ethernet Communication Module X X X X
B426 Ethernet Communication Module X X X X
B440 Plug-in Cellular Communicator7X X X
B441 Plug-in CDMA Cellular Communicator7X X X
B442 Plug-in GPRS Cellular Communicator7, 9 X X X X
B443 Plug-in HSPA+ Cellular Communicator7, 9 X X X X
B450 Plug-in Cellular Communicator X X X X
B520 Auxiliary Power Supply Module X X X X
B810 RADION receiver SD2, 3 X X
B820 SDI2 Inovonics Interface Module4X X
B915/B915I Basic Keypad
XXX
B920 Two-line Alphanumeric Keypad X X X
B921C Two-line Capacitive Keypad with Inputs8X X X
B930 ATM Style Alphanumeric Keypad X X X
B942/B942W Touch Screen Keypad XXX
D113 Battery Lead Supervision Module X X X X
D122/D122L Dual Battery Harness X X X
D125B Powered Loop Interface Module X X X X
D126 Standby Battery (12V, 7Ah)
D129 Dual Class A Initiation Circuit Module X X X
D130 Relay Module X X X
D132A Smoke Detector Reversing Relay Module5X X X
D185 Reverse Polarity Module X X X
D161 Phone Cord

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 14
Model Title UL
864
UL
985
Intrusion cUL
Intrusion
D162 Phone Cord
D192G Bell Circuit Supervision Module X X X
D928 Dual Phone Line Switcher X X X X
D1255RB Fire Keypad X X X X
D1256RB Fire Keypad X X X
D1257RB Fire Alarm Annunciator X X X X
D1218 12 V, 17.2 Ah Rechargeable Battery
D1255/D1255B Keypads (General Purpose) X X X
D1255W Text Keypad (white) X X X
D1260/D1260B Keypads6X X X
D1640 16.5 VAC 40 VA Transformer (120 VAC, 60 Hz) X X X
D1640-CA 16.5 VAC 40 VA Transformer for Canada (120 VAC, 60 Hz) X
D1640-SA 16.5 VAC 40 VA Transformer for Saudi Arabia (220 VAC,
50/60 Hz)
X
D8004 Transformer Enclosure X X X
D8125 POPEX Module X X X X
D8125MUX Multiplex Bus Interface X X X
D8128D OctoPOPIT Module X X X X
D8129 OctoRelay Module X X X X
D8130 Release Module X X X
D8132 Battery Charger Module X X X
D9127U/T POPIT Module X X X X
D9210C Access Control Interface Module X X X X
DX4010V2 USB/Serial Interface Module
DX4020 Network Interface Module X X X X
ITS-DX4020-G GPRS/GSM Communicator X X X
ICP-SDI-9114 SDI Splitter X X X
ITS-EZTS Tamper Switch X X X
ZX776Z PIR Motion Sensor with POPIT X
ZX794Z PIR Motion Sensor with POPIT X
ZX865 PIR/Microwave Motion Sensor with POPIT X
ZX938Z PIR Motion Sensor with POPIT X
ZX970 PIR/Microwave Motion Sensor with POPIT X
RFBT-A RADION specialty3X
RFDL-11-A RADION TriTech3X
RFDW-SM-A RADION contact SM3X
RFDW-RM-A RADION contact RM3
X
RFSM-A RADION smoke3X
X
RFRP-A RADION repeater3X
X
RFPR-12-A RADION PIR3
X
RFPR-C12-A RADION PIR C3
X
RFUN-A RADION universal transmitter3
X
RFPB-TB-A RADION panic3
X
RFPB-SB-A RADION panic3
X
RFKF-TB-A RADION keyfob3
X
RFKF-FB-A RADION keyfob3
X

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 15
Table 4: (B810) RADION receiver SD Compatible Accessories
Model Title
RFBT-A RADION specialty (bill trap)
RFDL-11-A RADION TriTech (motion detector)
RFDW-SM-A RADION contact SM (door/window contact)
RFPR-12-A RADION PIR (motion detector)
RFPR-C12-A RADION PIR C (motion detector – curtain)
RFUN-A RADION universal transmitter (universal contact)
RFGB-A RADION glassbreak (detector)
RFDW-RM-A RADION contact RM (door/window contact)
RFSM-A RADION smoke (detector - UL 985 only)
RFPB-SB-A RADION panic (single button)
RFPB-TB-A RADION panic (two-button)
RFKF-TB-A RADION keyfob (two-button)
RFKF-FB-A RADION keyfob (four-button)
Table 5: (B820) SDI2 Inovonics Interface Module Compatible Accessories
Model Title
EN1210 Universal Transmitter (Single-input)
EN1210EOL Universal Transmitter with EOL Resistor
EN1210W Door-Window Transmitter with Reed Switch
EN1215EOL Universal Transmitter with Wall Tamper and EOL Resistor
EN1215WEOL Door-Window Transmitter with Wall Tamper, Reed Switch, and EOL Resistor
EN1223D Water-Ver)
EN1223S Water-resistant Pendant Transmitter (Single-button)
EN1224-ON Multiple-Condition Pendant Transmitter
EN1233D Necklace Pendant Transmitter (Double-button)
EN1233S Necklace Pendant Transmitter (Single-button)
EN1235D Beltclip Pendant Transmitter (Double-button)
EN1235DF Fixed-location Transmitter (Double-button)
EN1235S Beltclip Pendant Transmitter (Single-button)
EN1235SF Fixed-location Transmitter (Single-button)
EN1242 Smoke Detector Transmitter
EN1247 Glass-break Detector Transmitter
EN1249 Bill Trap Transmitter
EN1260 Wall Mount Motion Detector
EN1261HT High Traffic Motion Detector
EN1262 Motion Detector With Pet Immunity
EN1265 360° Ceiling Mount Motion Detector
EN4200 Serial Receiver
1Where the fire alarm transmitter is sharing on premise communications equipment, the shared equipment must be UL Listed (ITE or fire protective signaling).
2Refer to Table 4: (B810) RADION receiver SD Compatible Accessories for compatible RADION devices.
3Refer to the device-specific installation instructions for each RADION wireless device.
4Refer to Table 5: (B820) SDI2 Inovonics Interface Module Compatible Accessories for compatible Inovonics devices.
5Refer to Table 34: Two-wire smoke detector compatibility table for more information (Household Fire Alarm applications only).
6Version 1.04 or above.
7A B450 plug-in communicator interface module is required in order to use the B44x cellular communicator.
8Only listed for cUL Propriety Berg and Residential Fire.
9Check for availability in your region.

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 16
Model Title
EN4204R Four Zone Add-on Receiver With Relay Outputs
EN5040-T High Power Repeater With Transformer
EN7016 Wireless Survey Kit
ENKIT-01 ISW-D8125CW-V2 and EN4200 Kit
Wireless Detectors are not approved
for use with alarm verification points.
For specific installation and operation
instructions, please refer to
manufacturers’ manuals.
3.3 Features in the GV4 Series
Control Panels
3.3.1 SDI Interconnect Wiring
Use interconnect wiring to easily connect an
SDI bus device to the SDI bus or an SDI2
device to the SDI2 bus without needing to
disconnect wires connected to the bus
terminals. Possible applications include:
Connecting a DX4010v2 to program the
control panel with Remote
Programming Software (RPS) at the
premises.
Connecting a keypad to test the control
panel.
3.3.2 Tip and Ring Posts
The tip and ring posts allow connecting a
phone or buttset for the purpose of
troubleshooting communications between the
control panel and the central station. This
connection allows monitoring of the dial tone,
handshaking tones from the receiver, and
communications signals.
3.3.3 Telephone Line Sniff
The control panels monitor the phone line for
the programmed supervision interval before
indicating phone line trouble.
3.3.4 Points
The Bosch Security Systems, Inc. D9412GV4
Control Panel provides up to 246 points of
protection. The D7412GV4 Control Panel
provides up to 75 points of protection. Point
programming parameters determine the
control panel’s response to open and shorted
conditions on the sensor loop for the point.
Several options allow individual point
programming to custom-fit the protection to
the installation.
Points 1 to 8 are located on the circuit board
(on-board points). They are standard sensor
loops. The remaining off-board points can be
located on point expansion modules on a
ZONEX bus, an SDI bus, and/or an SDI2 bus.
The ZONEX bus supports any combination of
POPIT points using D8128D OctoPOPITs,
D8125 POPEX Modules and D9127 POPITs, a
ISW-D8125CW-V2 Zonex Inovonics Interface
Module, or D8125MUX Modules. The SDI2 bus
supports any combination of B208 Octo-input
modules, B810 wireless receiver, or a B820
Inovonics Interface Module.
Any points programmed as fire
supervisory points are latching.
3.3.5 Areas and Accounts
The D9412GV4 supports up to 32 areas. The
D7412GV4 supports up to 8 areas. You can
assign all points to a single area or distribute
them over all supported areas.
UL requires that the DX4010v2
be used as a temporary
programming interface only.

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 17
The control panel is armed and disarmed by
area, and several areas can be armed and
disarmed with one menu function. A passcode
can also be assigned an authority level that
allows a user to arm an area from a remote
keypad in another area. Assigning each area its
own account number creates up to 32 separate
accounts in the D9412GV4 and up to 8
separate accounts in the D7412GV4. Assigning
the same account number to different areas,
groups them together in a single account.
Area options include exit tone and delay,
separate fire and burglary outputs, and
multiple opening and closing windows. Area
type can be used to create area
interdependencies for arming purposes.
3.3.6 Digital Communicator
The control panel uses a built-in digital
communicator to send reports to the receiver.
The control panel sends reports in either the
Modem4 or ANSI-SIA Contact ID format.
The control panel connects to an RJ31X or
RJ38X jack for telephone line seizure.
Connecting to the RJ31X complies with FCC
regulations for using the public telephone
network. The control panel can be
programmed to direct reports to four separate
telephone numbers. Adding the D928 Dual
Phone Line Switcher Module to the D9412GV4
or the D7412GV4 allows connection and
supervision of a second telephone line.
The system can route groups of Event Reports
to four different destinations through the
phone or over a network. Each report group
can be programmed to send reports to one or
more destinations. Primary and backup
reporting paths can be programmed for each
destination and each report group. A custom
option allows specification of individual Event
Reports to be sent.
3.3.7 Keypads
The control panel supports up to 32 keypads;
16 SDI2 keypads in any combination.
These include; B915, B920, B921C,
B930, and B942/B942W keypads on
the SDI2 bus. For example, you could
have eight B942 keypads, three B915
keypads, two B930 keypads, two
B921C keypads, and one B920 all
connected onto the same system).
16 SDI keypads in any combination.
These include; D1255, D1255RB,
D1256RB, D1257RB, D1260 (limited to
8), and D1265 keypads all connected
to a single SDI bus. If the control panel
loses communication with the keypad,
it sends SDI FAILURE in the Modem4
format or Expansion Module Failure
(333) in Contact ID format.
The control panel supervises all keypads on
the SDI2 bus. Any failure to receive an
expected response from an SDI2 keypad
results in a system fault display on all keypads
and an SDI Fault event is sent to the central
station if programmed to do so.
Table 6 on page 18 shows the keypads that are
compatible with D9412GV4/D7412GV4 v2.03
Control Panels. Refer to 18.0 Installer Menu for
complete details on programming keypad
options.

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 18
Table 6: Compatible Keypads
*This chart does not imply UL listings
Model Display Application
B915 2-line LCD
display
Burglary
B920 2-line LCD
display
Burglary/Access
B921C 2-line LCD
display
Burglary/Access
B930 5-line LCD
display
Burglary/Access
B942/B942W Touch screen
display
Burglary/Access
D1255RB* 16-character
alphanumeric
Burglary/Fire
D1256RB* 16-character
alphanumeric
Fire
D1257RB* 16-character
alphanumeric
Fire
D1255/
D1255B/
16-character
alphanumeric
Burglary
D1260/
D1260B
4-line by 20-
character
Burglary
D1265** LCD Touch
screen
Burglary
*UL requires all Fire System keypads to be
supervised.
**D1265 keypad has not been investigated by UL.
3.3.8 Keyswitch
Maintained or momentary closure devices such
as keyswitches allow any of the available areas
to be armed or disarmed. Point programming
determines the loop response and which area
a keyswitch controls.
3.3.9 Access Control
The D9412GV4 can control eight access doors
(each requiring the optional D9210C Access
Control Interface Module) with up to 999
uniquely identified cards or tokens. The
D7412GV4 can control two access doors with
up to 399 uniquely identified cards or tokens.
Any of the following can grant access:
Wiegand-style access control device
(card reader) connected to the D9210C
Access Control Interface Module
Request to enter (RTE) or request to
exit (REX) input
Unlock command on a
B915/B920/B921C/B930
The access control features of the D9412GV4
and D7412GV4 can deny access during armed
periods. The control panel can also grant
access only to certain authorized users
depending on whether the area is all on, part
on, or off. Programming for automatic
disarming when designated authorized users
are granted access is also possible.
The Dual Authentication feature can optionally
require passcode entry with presentation of
door credentials before access authorization is
granted.
3.3.10 Event Memory
The control panel retains point alarm and
trouble events in memory for each area. Event
memory can be viewed from keypads. The
control panel clears the previous events for an
area from the event memory when the area is
turned off.
3.3.11 Event Log
The system stores 1023 events from all areas
in its event log. For example, the system adds
at least two items to the log each time an area
is turned on (arm) or off (disarm), the open (or
close) event also contains the previous arming
state.
All events can be stored even if the control
panel does not send a report for them. The log
can be viewed at a keypad, or uploaded using
Remote Programming Software (RPS).
3.3.12 Ground Fault Detection
The Earth Ground Terminal on the control
panels is electrically isolated from all other
terminals to allow the control panels to detect
ground fault conditions. A Ground Fault Detect
Enable switch (S4) is located just under
Terminal 10, Earth Ground, on the control
panel. Refer to Section 4.5.2 Ground Fault
Detect Enable on page 21 for information on
operating this function.

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 19
3.3.13 Ground Fault Detection Added
Feature
When Ground Fault Detect is enabled (S4
closed), Points can be used for non-powered
fire-initiating devices such as heat detectors,
four-wire smoke detectors, and pull stations. A
D125B Powered Loop Interface or a D129 Dual
Class A Interface Module is not required when
connecting the non-powered fire-initiating
devices to Points.
3.3.14 Conettix Functions
The D6600/D6100i/D6100IPV6 Conettix
System supports data network
communications. Conettix allows the
D6600/D6100i/D6100IPV6 Receiver/Gateway
devices to connect to various network
technologies including Ethernet, UDP/IP, and
Ethernet cellular data.
Connecting to a data network is possible using
the COM4 or COM1 connection from the
D6600/D6100i Receiver to the D6680 Network
Adapter. Control panels can send reports
through telephone lines, Ethernet, UDP/IP, or
GPRS networks to the
D6600/D6100i/D6100IPV6 receiver to the
central station. Once events are received, they
can then be issued to automation software or a
network printer through a local area network
(LAN) or wide area network (WAN).
Sending events to the central station over a
LAN or WAN requires a network interface
module (NIM), such as the B420, B426, or
B450.
3.3.15 Programming
Use the RPS, or the Keypad Installer menu, to
program the control panels. Refer to the
Control Panels (D9412GV4/D7412GV4 v2.03)
Program Entry Guide (P/N: F01U265459) for
programming options.
3.3.16 Dual Authentication
The D9412GV4 and D7412GV4 control panels
can be configured to require two forms of
identification before processing certain system
commands. This feature requires a door
controller and a keypad to be installed within
proximity to each other for user convenience.
Dual Authentication requires a
D9210C door controller module or
B942/B942W touch screen keypad
even though the configured operation
may not be access.
A standard system user has authority to use
Dual Authentication if they have a passcode, a
door credential (token or card), and
appropriate command authority permissions
assigned in the door and keypads assigned
area. When enabled at a keypad, only the
following Passcode Functions require access
credentials with passcode entry, Arm / Disarm,
Cycle Door (Grant Access), Cycle Relay, and
Auto Re-arm. Refer to the Control Panels
(D9412GV4/D7412GV4 v2.03) Program Entry
Guide (P/N: F01U265459)and D9210C
Installation and Operation Guide (P/N:
F01U215232) for details on installation,
configuration and operation of this feature.
3.3.17 Other Features
The D9412GV4/D7412GV4 v2.03 Control
Panels have many programmable features.
Some of the features are listed below.
Complete details on all features are in the
Control Panels (D9412GV4/D7412GV4 v2.03)
Program Entry Guide (P/N: F01U265459):
Supervision of AC (primary power),
battery (secondary power), Zonex, SDI
and SDI2 buses, central processing unit
(CPU), and two telephone lines
Automatic System Test Reports
Remote access for programming,
diagnostics, and log uploads using the
remote programming software (RPS)
Fire alarm verification
Programmable alarm outputs
Programmable relay outputs
Opening and closing windows
SKEDs (scheduled events)
Limited local programming

D9412GV4/D7412GV4 v2.03 |Installation and System Reference Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 7/16 | F01U265457-09 20
4.0 Installation
4.1 Installation Preparation
This section contains a general installation
procedure and refers to other sections of the
document for detailed instructions.
Review this document and the Control Panels
(D9412GV4/D7412GV4 v2.03) Program Entry
Guide (P/N: F01U265459) before beginning the
installation to determine the hardware and wiring
requirements for the features used.
Have the following documentation available when
reading through this guide:
Control Panels (D9412GV4/D7412GV4
v2.03) Control Panel Owner’s Manual.
Before installation, become familiar with the
operation of RPS or the local Programmers menu.
4.2 Enclosure Options
Mount the control panel assembly in any of the
Bosch Security Systems, Inc. enclosures listed:
D8103 Universal Enclosure (tan)
D8109 Fire Enclosure (red)
D8108A Attack Resistant Enclosure (tan)
Refer to chapter 17.0 Approved Applications in
this guide to determine if the application requires
a specific enclosure.
4.3 Mounting Enclosure
1. Run the necessary wiring throughout the
premises.
2. Mount the enclosure in the desired location.
Use all five enclosure mounting holes. Refer
to Figure 2.
3. Pull the wires into the enclosure.
Electromagnetic interference (EMI)
can cause problems on long wire runs.
Figure 2: Enclosure Mounting
1 - Point chart label
2 - Mounting skirt hooks (2)
3 - Module mounting holes (12)
4 - Tamper switch mounting holes (5)
5 - Skirt mounting hole (1)
6 - Enclosure mounting holes (5)
7 - Mounting skirt hook holes (2)
8 - Back of D9412GV4/D7412GV4 Control Panel
9 - Lock down tab
8
2
1
324
3
7
5
9
6