Bosch D9127U User manual

For more information on POPIT installation (including wire type, length, and run) and
programming, refer to the D8125 POPEX Operation and Installation Guide (P/N: 74-04247-000)
and control panel operation, installation, and programming manuals. Install a 33 kΩ end-of-line
resistor at the farthest point on the loop for proper supervision. Replace the POPIT cover
when the wiring is completed.
Callout ― Description
1 ― D8125 POPEX Module
2 ― D9127U/T POPIT Module
3 ― Tab
4 ― DIP Switch
5 ― Reed switch (D9127T only)
6 ― Detector loop
7 ― 33 kΩ EOL resistor
8 ― Terminals (all): 12 AWG solid (maximum); 22 AWG (0.1 mm) stranded (minimum)
9 ― Zone expansion loop to other POPITs
10 ― Supervised
11 ― Wire opening of POPIT base
Figure 1: POPIT Wiring
-
-
+
+
GND
OUT
IN
AUX
DATA LOOP
- - + + - +
(-)
(+)
1
43
2
5
67
8
9
11
3
10
3
NOTICE!
When using 12 AWG (0.1 mm) maximum wire, use solid wire. If you use stranded
wire, take care to insert all of the strands into the terminal block.
3 | Wiring Instructions
2 | Installation
2.1 | Remove the cover
2.2 | Remove the PCB
2.3 | Mount the POPIT base
Pull the wiring through the wiring opening
(refer to Figure 1). Mount the POPIT base
using the supplied hardware to prevent
shorting the PCB.
2.4 | Replace the PCB
1. Grasp the terminal block on the PCB with
one hand. Insert the DIP switch end of the
PCB under the single tab.
2. Carefully but firmly, pull the two tabs on
the opposite ends away from the PCB.
3. Gently lay the PCB in place and, if
necessary, carefully, push the two tabs
toward the PCB until the PCB is firmly in
place.
1. Insert a small flat-head screwdriver into
one of the small slots in the side of the
POPIT.
2. Twist the screwdriver and remove the
cover.
1. Grasp the terminal block on the PCB in
one hand.
2. Three tabs hold the PCB. At the end with
the two tabs, carefully but firmly, push
one tab away from the PCB and lift the
corner.
3. Carefully but firmly, push the other tab
away from the PCB and lift the entire
PCB from the base.
Control
panel
DIP switch 0 setting
D7212B1
D8112
D9112B1
Leave switch 0 ON.
D9412 Refer to 9000 Series
Operation
and Installation Guide
(P/N: 74-07692-000).
D9412G
D7412G
Refer to Section 4.
D7212G Refer to Section 4.
D7212GV2 Refer to Section 4.
D7212GV3 Refer to Section 4.
D7212GV4
D9412GV4
D7412GV4
Refer to Section 4.
B9512G
B9512G-E
B8512G
B8512G-E
Refer to Section 4.
For additional D9127 installation
information, refer to the compatible panel
installation documentation.
Table 1: DIP switch 0 setting
Use the steps in this section to install and
configure the POPIT module.
2.5 | Configuration of DIP switch
Refer to Table 1 for DIP switch 0 settings and
Section 4 for DIP switch configuration settings
for ZONEX and ZONEX 2.
1 | Overview
The D9127 Series POPIT Modules includes
the D9127T (with magnetic tamper switch)
and the D9127U (without tamper). They
are used with a compatible control panel
to expand beyond its standard number of
on-board initiating points. Future system
expansion is very economical as D9127
Series POPITs can be added anywhere
along the two-wire data expansion loop.
Both modules include proven technology
that combines point supervision with
individual device addressing on one pair
of wires. Screw terminals provide reliable
connections for the data expansion loop
and supervised sensor loop wiring.
The units are small and easily installed in
standard outlet boxes, above false ceilings,
closets, or other accessible locations.

© 2016Bosch Security Systems, Inc. 4998132020 | 11| 2016.01
en Installation Guide
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
USA
www.boschsecurity.us
POPIT Module
D9127U/T
Copyright
This document is the intellectual property of
Bosch Security Systems, Inc. and is protected
by copyright. All rights reserved.
Trademarks
All hardware and software product names used
in this document are likely to be registered
trademarks and must be treated accordingly.
Bosch Security Systems, Inc. product
manufacturing dates
Use the serial number located on the product
label and refer to the Bosch Security Systems,
Inc. website at
http://www.boschsecurity.com/datecodes/.
5 | Specifications
Operating Voltage Nominal 12 VDC
supplied by control
panel
Operating Current
per D9127U/T
0.8 mA Standby
0.8 mA Alarm
4 | ZONEX and ZONEX 2 point address chart
Address1Switch
ZONEX
1
ZONEX
2
B299 0 1 2 3 4 5 6
009 129 x00* ON ON ON ON ON ON ON
010 130 x01* ON ON ON ON ON ON
011 131 x02* ON ON ON ON ON ON
012 132 x03* ON ON ON ON ON
013 133 x04* ON ON ON ON ON ON
014 134 x05* ON ON ON ON ON
015 135 x06* ON ON ON ON ON
016 136 x07* ON ON ON ON
017 137 x08* ON ON ON ON ON ON
018 138 x09 ON ON ON ON ON
019 139 x10 ON ON ON ON ON
020 140 x11 ON ON ON ON
021 141 x12 ON ON ON ON ON
022 142 x13 ON ON ON ON
023 143 x14 ON ON ON ON
024 144 x15 ON ON ON
025 145 x16 ON ON ON ON ON ON
026 146 x17 ON ON ON ON ON
027 147 x18 ON ON ON ON ON
028 148 x19 ON ON ON ON
029 149 x20 ON ON ON ON ON
030 150 x21 ON ON ON ON
031 151 x22 ON ON ON ON
032 152 x23 ON ON ON
033 153 x24 ON ON ON ON ON
034 154 x25 ON ON ON ON
035 155 x26 ON ON ON ON
036 156 x27 ON ON ON
037 157 x28 ON ON ON ON
038 158 x29 ON ON ON
039 159 x30 ON ON ON
040 160 x31 ON ON
041 161 x32 ON ON ON ON ON ON
042 162 x33 ON ON ON ON ON
043 163 x34 ON ON ON ON ON
044 164 x35 ON ON ON ON
045 165 x36 ON ON ON ON ON
046 166 x37 ON ON ON ON
047 167 x38 ON ON ON ON
048 168 x39 ON ON ON
049 169 x40 ON ON ON ON ON
050 170 x41 ON ON ON ON
051 171 x42 ON ON ON ON
052 172 x43 ON ON ON
053 173 x44 ON ON ON ON
054 174 x45 ON ON ON
055 175 x46 ON ON ON
056 176 x47 ON ON
057 177 x48 ON ON ON ON ON
058 178 x49 ON ON ON ON
059 179 x50 ON ON ON ON
1ZONEX 1: Points 9 to 127 (D9412G); Points 9 to 75 (D7412G).
ZONEX 2: Points 129 to 247 (D9412G).
B299: x = B299 module address 0-5
* These point numbers are not available for B299 address 0.
Address1Switch
ZONEX
1
ZONEX
2
B299 0 1 2 3 4 5 6
060 180 x51 ON ON ON
061 181 x52 ON ON ON ON
062 182 x53 ON ON ON
063 183 x54 ON ON ON
064 184 x55 ON ON
065 185 x56 ON ON ON ON
066 186 x57 ON ON ON
067 187 x58 ON ON ON
068 188 x59 ON ON
069 189 x60 ON ON ON
070 190 x61 ON ON
071 191 x62 ON ON
072 192 x63 ON
073 193 x64 ON ON ON ON ON ON
074 194 x65 ON ON ON ON ON
075 195 x66 ON ON ON ON ON
076 196 x67 ON ON ON ON
077 197 x68 ON ON ON ON ON
078 198 x69 ON ON ON ON
079 199 x70 ON ON ON ON
080 200 x71 ON ON ON
081 201 x72 ON ON ON ON ON
082 202 x73 ON ON ON ON
083 203 x74 ON ON ON ON
084 204 x75 ON ON ON
085 205 x76 ON ON ON ON
086 206 x77 ON ON ON
087 207 x78 ON ON ON
088 208 x79 ON ON
089 209 x80 ON ON ON ON ON
090 210 x81 ON ON ON ON
091 211 x82 ON ON ON ON
092 212 x83 ON ON ON
093 213 x84 ON ON ON ON
094 214 x85 ON ON ON
095 215 x86 ON ON ON
096 216 x87 ON ON
097 217 x88 ON ON ON ON
098 218 x89 ON ON ON
099 219 x90 ON ON ON
100 220 x91 ON ON
101 221 x92 ON ON ON
102 222 x93 ON ON
103 223 x94 ON ON
104 224 x95 ON
105 225 x96 ON ON ON ON ON
106 226 x97 ON ON ON ON
107 227 x98 ON ON ON ON
108 228 x99 ON ON ON
109 229 ON ON ON ON
110 230 ON ON ON
1ZONEX 1: Points 9 to 127 (D9412G); Points 9 to 75 (D7412G).
ZONEX 2: Points 129 to 247 (D9412G).
B299: x = B299 module address 0-5
* These point numbers are not available for B299 address 0.
Address1Switch
ZONEX
1
ZONEX
2
B299 0 1 2 3 4 5 6
111 231 ON ON ON
112 232 ON ON
113 233 ON ON ON ON
114 234 ON ON ON
115 235 ON ON ON
116 236 ON ON
117 237 ON ON ON
118 238 ON ON
119 239 ON ON
120 240 ON
121 241 ON ON ON ON
122 242 ON ON ON
123 243 ON ON ON
124 244 ON ON
125 245 ON ON ON
126 246 ON ON
127 247 ON ON
128 248 not available
1ZONEX 1: Points 9 to 127 (D9412G); Points 9 to 75 (D7412G).
ZONEX 2: Points 129 to 247 (D9412G).
B299: x = B299 module address 0-5
* These point numbers are not available for B299 address 0.
Bosch Sicherheitssysteme
GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany