Bosch DS304 User manual

DS304
EN
Installation Instructions
Passive Infrared (PIR)
Detector

Bosch Security Systems | 1/05 | 4998122424F
EN | 21.0 Installation Considerations
1.0 Installation Considerations
• Not suitable for outdoor use.
• Point away from direct and indirect sunlight.
• Point away from glass or other objects that rapidly
change temperature.
• Do not install this detector where pets are present.
• Select a mounting location where an intruder is most
likely to cross the coverage pattern perpendicular to
the detection zones.
• Mount the detector 6.6 ft to 8.5 ft (2 m to 2.6 m)
above the floor.
2.0 Installation
Refer to Figures 1 and 2when preparing the detector.
Ensure the mounting surface is solid and
free of vibration.
1. Remove the cover by inserting a thin, flat-blade
screwdriver into the notch at the bottom of the
cover and prying up.
2. Remove the circuit board by pressing one of the
circuit board retainer tabs toward the side of the
enclosure and lifting the circuit board up and out of
the enclosure base.
3. Remove the mirror by sliding it out of its tracks.
4. Remove an appropriate wiring knockout.
5. To surface or corner mount, go to Section 2.1 Surface
or Corner Mounting. To bracket mount, go to
Section 2.2 Bracket Mounting on page 3.
2.1 Surface or Corner Mounting
1. Remove the knockout holes for either surface or
corner mounting.
2. Using the enclosure as a template, mark the location
for the mounting screws. Use wall anchors as
needed.
3. Mount the detector.
4. Insert the wiring.
5. For strain relief, attach the cable to the cable
tie with the plastic tie-down (supplied).
6. Replace the mirror and circuit board.
Figure 1: Rear Enclosure
7
3
1
55
6
2
3
6
4
1 - Wiring knockouts (3)
2 - Cable tie/strain relief
3 - Corner mounting holes (2)
4- Surface mounting holes (4)
5 - Circuit board retainer tabs (2)
6 - Mirror tracks (2)
7 - Bracket mounting hole
Figure 2: Circuit Board
1 - Securing screw 4 - LED
2 - Terminal strip (2) 5 - Configuration switches
3 - Tamper switch 6 - Program jumper
123
OP N
2
6
5
1
2
3
4
DS304| Installation Instructions |

EN | 3
DS304| Installation Instructions |
Bosch Security Systems | 1/05 | 4998122424F
3.0 Mirror Adjustment
2.2 Bracket Mounting
1. Attach the bracket to the mounting surface using the
instructions supplied with the bracket.
2. Knock out the bracket mounting hole in the
enclosure base and attach the enclosure to the
bracket using the instructions supplied with the
bracket.
3. Insert the wiring.
4. For strain relief, attach the cable to the cable
tie with the plastic tie-down (supplied).
5. Replace the mirror and circuit board.
3.0 Mirror Adjustment
1. Determine the appropriate angle for the installation
using the chart in Figure 3.
Touching the mirror surface can reduce
performance.
2. Use the angle adjustment markings shown in
Figure 4 to set the maximum detection range needed.
3. Slide the mirror forward or back until the angle
adjustment markings align with the markers on each
side of the frame. Use the chart in Figure 3 located
inside the front cover to set the correct angle.
4. Adjust the horizontal protection coverage during the
Walk Test. Refer to Section 7.0 Setup and Walk Testing
on page 5.
4.0 Wiring
Apply power only after all connections are
made and inspected.
Do not coil excess wire inside the enclosure.
Seal the wire entrance with the plug
provided.
Figure 3: Mirror Angle Adjustment
X
Y
2.0 (6.5)
2.3 (7.5)
2.6 (8.5)
Broad
20 (6) 35 (10) Curtain 40 (12) 70 (20
)
-10° - 6° - 4° - 2°
-12° - 8° - 4° - 2°
-14° - 10° - 6° - 4°
Y m (ft)X m (ft)
X = maximum range Y = mounting height
Figure 5: Terminal Strip Connections
456789101
1
1
2
3
1 (SH) Shield (optional): Connection for ground
wire from shielded cable.
2 (S/U*) Set/Unset (optional): Use as an alarm
memory control input for remote panel
arming or disarming. Also used as an
electronic alarm output. Only one detector
should be connected for each detector
group.
3 (WT*) Walk Test (optional): Use for Walk Test
remote control through the control panel.
Allows a command at the control panel to
enable or disable the Alarm LED.
4 & 5 (T) Tamper: Tamper contact is normally closed
(open when cover opens). Rated 125 mA
at 28 V.
6 & 9 (SP) Spare
7 & 8 (AL) Alarm: Solid-state Form “A” relay contacts
normally closed (open on alarm). Rated
100 mA at 30 V. Do not use with
capacitive or inductive loads.
10 (-) & Input power: Use no smaller than
11(+) 22 AWG (0.8 mm) wire.
* Use a control panel or switch to 0 VDC with the
S/U and WT option control inputs. Open control
inputs are HIGH level (internal pull-up). Switch the
input to achieve the LOW level (from <1.5 V up to a
2 k
Ω resistance maximum). The active level is
user-configurable.
Figure 4: Adjustment Selections
Mirror with expanded view showing the angle
adjustment markings.
-16
-8
0
+

Bosch Security Systems | 1/05 | 4998122424F
EN | 4
5.0 Configuration
5.1 Program Jumper for the S/U Control
Terminal
Use the S/U control terminal as an alarm memory
control input by setting the jumper in the upper position
as shown in Item 1 of Figure 6.
Use the S/U control terminal as an electronic alarm
output (open collector) by setting the jumper in the
lower position as shown in Item 2 of Figure 6.
5.2 User DIP Switches
5.3 Adjusting Sensitivity
Table 1: Sensitivity Settings
DIP Switch 2 OFF
Standard Sensitivity (Default):
Recommended for maximum false
alarm prevention.
Tolerates environmental extremes.
Not recommended for curtain
patterns.
DIP Switch 2 ON
Intermediate Sensitivity:
Recommended for any location
where an intruder is expected to
cover only a small portion of the
protected area, or when you want
improved catch performance.
Does not tolerate normal
environments.
5.4 LED Setup Without S/U and WT
Remote Control Panel Inputs
Table 2: LED Setup Without Control Panel Inputs
DIP Switch Settings
LED
Operation
User DIP Switch 1
Walk Test
User DIP Switch 3
Set/Unset
Disable LED Any ON
Enable LED OFF (default) OFF (default)
5.0 Configuration
Figure 7: User DIP Switches
3
12
12 3
OPEN
1 - Walk Test polarity (Refer to Section 5.4 LED
Setup Without S/U and WT Remote Control
Panel Inputs.)
2 - Sensitivity (Refer to Section 5.5 Setup for
Remote Control Alarm Memory and LED
Operation Using S/U and WT Inputs.)
3 - Set/Unset polarity (Refer to Section 5.4.)
1 - Alarm memory control input
2 - Electronic alarm output
Figure 6: Program Jumper Settings
2
1
S/U
AL S/U
AL
DS304| Installation Instructions |

EN | 5
DS304| Installation Instructions |
Bosch Security Systems | 1/05 | 4998122424F
5.5 Setup for Remote Control Panel
Alarm Memory and LED Operation
Using S/U and WT Inputs
Table 3: User DIP Switch Selection
DIP
Switch
Function ON
OFF
1 Select
Walk Test
polarity
Low (0 V) =
Walk Test
active
High (12 V) =
Walk Test
active (default)
3 Select
Set/Unset
polarity
Low (0 V) =
Unset
High (12 V) =
Set
High (12 V) =
Unset (default)
Low (0 V) =
Set (default)
Ensure the control terminal program jumper is configured as
shown in Item 1 of Figure 5 on page 3 (refer to Section 5.1
Program Jumper for the S/U Control Terminal on page 4).
6.0 Remote Control Operation
Table 4: Remote Control Operation
Control Line Status
Arming
Terminal
Status
Walk Test
Terminal
Status
Detector
Status
LED Status
Set OFF or ON Memory
ready OFF
Stored
alarm
Rapid flashing
(2 Hz)
OFF
No stored
alarm OFF
Power up Slow flashing
(0.5 Hz)
Alarm
activity
ON for
4 sec
Unset
ON
No alarms OFF
Transition
from Unset
to Set
OFF or ON Memory
cleared
OFF
6.0 Remote Control Operation
7.0 Setup and Walk Testing
Enable the LEDs before performing a
Walk Test.
1. Replace the cover and insert the cover tamper screw
(if desired).
2. Apply power to the unit.
3. Wait at least 2 min for the detector to stabilize and
no motion is detected (Figure 8).
4. Watch the LED as you walk to the farthest edge of
the coverage pattern. Walk closer to the detector by
crossing the pattern.
The LED lights when it detects you crossing the
coverage pattern.
5. Repeat from the other side.
If the desired range is not achieved, try angling the
mirror up or down to assure the coverage pattern is
not aimed too high or too low.
8.0 Maintenance
At least once a year, check the range and coverage
according to Section 7.0 Setup and Walk Testing. To
ensure continuous operation, instruct the end user to
walk through the outer edge of the coverage area daily
and observe the LED operation (if used). This also
assures an alarm output prior to arming.
Figure 8: Walk Testing
Walk test across the pattern.

Bosch Security Systems | 1/05 | 4998122424F
EN | 69.0 Coverage Patterns
9.0 Coverage Patterns
DS304| Installation Instructions |
Figure 10: Curtain Mirror Coverage (optional OMLR93)
1 - Top view
2 - Side view, mirror adjusted to -2°
3 - Front polished surface view, mirror segment for pattern reference
0 m
A
CD
E
B
+2
0
-8
-16
+2
0
-8
-16
3
2
0 m 0 m
2 m
21 m
B
DC
EA
1
0 m
1.9 m
1.9 m 21 m
1 - Top view
2 - Side view, mirror adjusted to -6°
3 - Front polished surface view, mirror segment for pattern reference
Figure 9: Wide Angle Coverage
ABCDEFGHI
JKLMN
+2
0
-8
-16
+2
0
-8
-16
Q
P
O
3
E
G
F
I
H
C
D
A
B
N
M
L
K
J
P
Q
O
1
0 m
5.35 m
0 m
5.35 m 11 m
2
0 m
2 m
11 m
0 m

EN | 7
DS304| Installation Instructions |
Bosch Security Systems | 1/05 | 4998122424F
10.0 Specifications
Table 5: Specifications
Input Power Use only an approved limited power source.
Standby Power No internal standby battery. Standby power must be provided by an approved limited power
source. For each hour of standby time needed, 22 mAh is required.
Supply Voltage
Range: 8 VDC to 16 VDC
Nominal: 12 VDC nominal
Maximum Ripple
(0 to 120 Hz): 2 Vpp
Voltage Monitoring: Alarm at less than 4 V
Current Consumption (at 12 V)
Quiescent: 5.5 mA
Maximum at standby
(LED on): 8.5 mA
Alarm Output
Relay Contact
(Solid-State Relay): Opens in alarm; 30 V, 100 mA; R, <20 Ω
Alarm Holding Time: 4 sec
Alarm Relay Connect to a safety extra-low voltage (SELV) circuit only.
Optional Electronic Alarm Output (alternate use of S/U Terminals)
Inactive: Open collector output
Active: Switch low through 1 kΩ
Tamper Contact
28 V, 125 mA
Connect to a SELV circuit only.
Connect the tamper circuit to a 24-hour protection circuit.
Control Inputs (Walk Test, S/U)
LOW: 1.5 V or less
HIGH: 3.5 V or more
Coverage
Wide Angle Mirror: 11 m x 11 m
Curtain Mirror: 21 m x 3 m
Walking Speeds
Wide Angle Mirror: 0.2 m/s to 3.0 m/s
Curtain Mirror: 0.2 m/s to 4.0 m/s
Sensitivity Standard or intermediate
Ambient Conditions
Storage Temperature: -20°C to +60°C
Operating Temperature: -10°C to +55°C
Air Humidity (EN60721): <95% rH, non-condensing
Housing Protection
(EN60529, EN50102): IP41/IK02
Options B338 Ceiling Mount Bracket*
OMLR93-3 Curtain Mirror
*Misaligning these brackets can reduce the detector’s range and increase the dead zone area.
10.0 Specifications

Bosch Security Systems
130 Perinton Parkway
Fairport, NY 14450-9199 USA
www.boschsecurity.us
Customer Service: [phone]
Technical Support: [phone]
© 2004 Bosch Security Systems
4998122424F