Bosch Solution 16i User manual

Solution 16i
Security System
Installation Manual
EN
Security Systems

COPYRIGHT NOTICE
Unless otherwise indicated, this publication is the
copyright of Bosch Security Systems Pty Ltd (“Bosch”).
All rights are reserved.You may download a single copy
of this publication. By downloading the publication you
agree that you will: (i) only use the publication for your
own reference; (ii) not commercially exploit or charge
any person for the use of the publication; and (iii) not
modify the publication in any way without the prior
written permission of Bosch. Except as specied above
or where authorised by the Copyright Act 1968 (Cth), no
part of this publication may be reproduced, transmitted,
modied or stored in any form or by any means, without
the prior written permission of Bosch.
TRADEMARKS
Throughout this document trademark names may have
been used. Rather than put a trademark symbol in every
occurrence of a trademark name, we state that we are
using the names only in an editorial fashion and to the
benet of the trademark owner with no intention of
infringement of the trademark.
NOTICE OF LIABILITY
While every eort has been taken the accuracy of this
document, neither Bosch Security Systems Pty Ltd nor
any of its ocial representatives shall have any liability
to any person or entity with respect to any liability, loss
or damage caused or alleged to be caused directly or
indirectly by the information contained in this book.
Should you nd any error on inconsistency, please notify
us accordingly.
Bosch Security Systems Pty Ltd reserves the right to
make changes to features and specications at any time
without prior notication in the interest of ongoing
product development and improvement.
TELEPERMIT NOTE
The grant of a Telepermit for a device in no way indicates
Telecom acceptance of responsibility for the correct
operation of that device under all operating conditions.
This equipment shall not be used in any manner that
could constitute a nuisance to other Telecom customers.
Immediately disconnect this equipment should it become
physically damaged, and arrange for its disposal or repair.
The transmit level from this device is set as a xed level
and because of this there may be circumstances where
the performance is less than optimal. Before reporting
such occurrences as faults, please check the line with a
standard telepermitted telephone.
Warnings
1) This product must be installed by a qualied
and licensed security installer.
2) This product may not perform as expected if
installed incorrectly.
3) Some features of this product, including but not
limited to Back to Base reporting, SMS and
Email Reporting and Automatic Time and Date
Adjustments require a working telephone line
to operate and telephone communication
service provider charges are applicable.
4) Australian standard AS 2201 requires regular
service by qualied and licensed security
persons and regular user testing. Please consult
your security alarm company for further details.
5) Incorrect programming of parameters can result
in operation contrary to what may be desired.
6) Leave the mains adapter plugged in at all times.
7) Leave the telephone line plugged in at all times
under normal conditions.
8) The Product Identication Label for this product
which is supplied in the resistor pack, must be
axed to the outside of the enclosure during
installation.
TELEPERMIT N12138
SOLUTION 16i
Intrusion Control Panel
N12138
Made In
Australia
PTC 211 / 07 / 076
RN = 0.5
TELEPERMIT
This Bosch Solution 16i
CC500B Alarm System
may be connected to the
Telecom Network
9) This equipment shall not be set up to make
automatic calls to the Telecom ‘111’ Emergency
Service.
Solution 16i  Installation Manual
ii Bosch Security Systems 07/10 BLCC500I

iii
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Contents
CONTENTS
COPYRIGHT NOTICE ................................................................................................................................................................... II
TRADEMARKS ............................................................................................................................................................................. II
NOTICE OF LIABILITY ................................................................................................................................................................. II
TELEPERMIT NOTE ..................................................................................................................................................................... II
SECTION 1
OVERVIEW ................................................................................................................................................11
FEATURES .................................................................................................................................................................................11
OVERVIEW ................................................................................................................................................................................12
SECTION 2
INSTALLING THE HARDWARE .................................................................................................................21
ABOUT THE PANEL ..................................................................................................................................................................21
ENCLOSURES ...........................................................................................................................................................................21
ENCLOSURE FIXING METHOD ................................................................................................................................................21
INSTALLING THE TAMPER SWITCH ........................................................................................................................................21
ENCLOSURE MODULE SPACES ...............................................................................................................................................21
INSTALLING PANELS AND MODULES ...................................................................................................................................22
CONNECTING POWER TO THE PANEL ...................................................................................................................................24
CONNECTING THE BATTERY ...................................................................................................................................................24
AC MAINS TRANSFORMER OPTION .......................................................................................................................................24
PANEL LED INDICATORS .........................................................................................................................................................25
KEYPAD BUTTON FUNCTIONS ...............................................................................................................................................25
KEYPAD SETUP ........................................................................................................................................................................26
KEYPAD ADDRESS SELECTION ..............................................................................................................................................26
STATUS ICONS & LED INDICATORS ........................................................................................................................................26
KEYPAD TONES ........................................................................................................................................................................27
VANDAL RESISTANT KEYPADS ..............................................................................................................................................28
WATERPROOF EXTERNAL LAN READERS .............................................................................................................................28
EXPANSION MODULES ...........................................................................................................................................................29
EXPANSION MODULE CONFIGURATION.............................................................................................................................211
EOL RESISTOR COLOUR CODE .............................................................................................................................................211
SECTION 3
WIRING DIAGRAMS..................................................................................................................................31
ZONE WIRING ...........................................................................................................................................................................31
BOARD CONNECTORS .............................................................................................................................................................32
TERMINAL DESCRIPTIONS .....................................................................................................................................................32
LAN OVERVIEW .......................................................................................................................................................................35
LAN WIRING .............................................................................................................................................................................35
SYSTEM EARTHING .................................................................................................................................................................36
TERMINATING THE LAN ..........................................................................................................................................................36
SECTION 4
PROGRAMMING OVERVIEW ...................................................................................................................41
PROGRAMMING OVERVIEW ..................................................................................................................................................41
ENTERING PROGRAMMING MODE ........................................................................................................................................41
EXITING PROGRAMMING MODE ...........................................................................................................................................41
PROGRAMMING STRUCTURE ................................................................................................................................................41
INTERPRETING THE TEXT DISPLAY........................................................................................................................................41
PROGRAMMING BIT OPTIONS ...............................................................................................................................................42
PROGRAMMING TEXT LOCATIONS........................................................................................................................................42
PROGRAMMING TELEPHONE NUMBERS ..............................................................................................................................43
PROGRAMMING LIST OPTIONS .............................................................................................................................................43
PROGRAMMING THE CLOCK ..................................................................................................................................................43

Solution 16i  Installation Manual  Contents
iv Bosch Security Systems 09/11 BLCC500I
GETTING STARTED BACK TO BASE ........................................................................................................................................44
DEFAULTING THE SYSTEM ......................................................................................................................................................44
DOMESTIC TEMPLATE DEFAULTS ..........................................................................................................................................44
DTMF CONTROL FUNCTIONS ................................................................................................................................................45
DIRECT LINK PROGRAMMING ...............................................................................................................................................46
ZONE ARRAY ............................................................................................................................................................................46
BASIC REPORTING REFERENCE .............................................................................................................................................46
SYSTEM TROUBLE EVENT LISTING ........................................................................................................................................47
HOW SYSTEM TROUBLES ARE DISPLAYED ...........................................................................................................................47
PROGRAMMING LOCATIONS REFERENCE TABLE ..............................................................................................................410
SECTION 5
ACCESS PROGRAMMING .........................................................................................................................51
USER DEFAULT TABLE .............................................................................................................................................................52
USER PIN CODES ......................................................................................................................................................................52
Erase User .......................................................................................................................................................................................................................... 5-2
Change Own PIN ............................................................................................................................................................................................................. 5-2
Change Other PIN ........................................................................................................................................................................................................... 5-2
Add PIN ............................................................................................................................................................................................................................... 5-3
Delete PIN .......................................................................................................................................................................................................................... 5-3
View PIN ............................................................................................................................................................................................................................. 5-3
PROXIMITY TOKENS & CARDS ...............................................................................................................................................54
Add Token .......................................................................................................................................................................................................................... 5-4
Delete Token ..................................................................................................................................................................................................................... 5-4
Token Status .....................................................................................................................................................................................................................5-4
RF RADIO KEYFOBS .................................................................................................................................................................55
Add Keyfob........................................................................................................................................................................................................................ 5-5
Delete Keyfob ................................................................................................................................................................................................................... 5-5
Test Keyfob ........................................................................................................................................................................................................................ 5-5
USER PROPERTIES ...................................................................................................................................................................55
User Name ......................................................................................................................................................................................................................... 5-5
Area Assignment ............................................................................................................................................................................................................. 5-6
User Options ..................................................................................................................................................................................................................... 5-6
UNDERSTANDING TIMER GROUPS ........................................................................................................................................57
Timer Group Example ............................................................................................................................................................................ 5-7
Timer Group ...................................................................................................................................................................................................................... 5-7
Access Group .................................................................................................................................................................................................................... 5-8
PIN Length ......................................................................................................................................................................................................................... 5-8
PIN Retry Count ............................................................................................................................................................................................................... 5-9
Installer PIN ....................................................................................................................................................................................................................... 5-9
PIN Expire Time ................................................................................................................................................................................................................ 5-9
PROX READERS ........................................................................................................................................................................59
Name ................................................................................................................................................................................................................................... 5-9
Area Assignment ...........................................................................................................................................................................................................5-10
Access Assignment .......................................................................................................................................................................................................5-10
Reader Options ..............................................................................................................................................................................................................5-10
SECTION 6
AREA PROGRAMMING .............................................................................................................................61
Example: Simple Two Area System ..................................................................................................................................................... 6-1
AREA COMMANDS ..................................................................................................................................................................61
Area Status ........................................................................................................................................................................................................................ 6-1
Turn Area On/O ............................................................................................................................................................................................................. 6-2
Turn All Areas On ............................................................................................................................................................................................................ 6-2
Turn All Areas O ............................................................................................................................................................................................................ 6-2
Move To Area .................................................................................................................................................................................................................... 6-3
Chime On/O ................................................................................................................................................................................................................... 6-3
Chime Mode ..................................................................................................................................................................................................................... 6-3
To set the chime mode. ........................................................................................................................................................................ 6-4
AREA PROPERTIES ..................................................................................................................................................................64
Area Name ......................................................................................................................................................................................................................... 6-4
General Options .............................................................................................................................................................................................................. 6-4

v
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Contents
Input Options ................................................................................................................................................................................................................... 6-5
Output Options ............................................................................................................................................................................................................... 6-6
Reporting Options .......................................................................................................................................................................................................... 6-7
Strobe Trigger................................................................................................................................................................................................................... 6-7
AREA REPORTING ....................................................................................................................................................................68
Account Dest 1................................................................................................................................................................................................................. 6-8
Account Dest 2................................................................................................................................................................................................................. 6-8
Open / Close Route ........................................................................................................................................................................................................ 6-8
AREA TESTING .........................................................................................................................................................................68
Area Watch ........................................................................................................................................................................................................................ 6-8
User Test Interval ............................................................................................................................................................................................................. 6-9
Service Interval ................................................................................................................................................................................................................ 6-9
Test Options ...................................................................................................................................................................................................................... 6-9
SECTION 7
INPUT PROGRAMMING ...........................................................................................................................71
INPUT COMMANDS .................................................................................................................................................................72
Zone Status ....................................................................................................................................................................................................................... 7-2
Zone Array ......................................................................................................................................................................................................................... 7-2
Bypass Zones .................................................................................................................................................................................................................... 7-2
Set Chime Zones ............................................................................................................................................................................................................. 7-3
Set Part 2 Zones ............................................................................................................................................................................................................... 7-3
Smoke Sensor Reset....................................................................................................................................................................................................... 7-3
ZONE DEFAULT TABLE .............................................................................................................................................................74
ZONE PROPERTIES ..................................................................................................................................................................74
Zone Name ........................................................................................................................................................................................................................ 7-4
Zone Type .......................................................................................................................................................................................................................... 7-5
Area Assignment ............................................................................................................................................................................................................. 7-6
Pulse Count ....................................................................................................................................................................................................................... 7-7
Pulse Count Time ............................................................................................................................................................................................................ 7-7
UNDERSTANDING ACCESS GROUPS .....................................................................................................................................77
Door Access Group Example ................................................................................................................................................................ 7-7
Access Group .................................................................................................................................................................................................................... 7-8
Report Route ................................................................................................................................................................................................................... 7-8
Report Options ................................................................................................................................................................................................................ 7-8
The above options are programmable per zone. ............................................................................................................................. 7-8
Zone Options....................................................................................................................................................................................................................7-9
ADDING RF SENSORS ............................................................................................................................................................710
RF Sensor - Direct Entry Mode ........................................................................................................................................................... 7-10
Add RF Device ................................................................................................................................................................................................................7-10
RF Sensor - Learn Mode ....................................................................................................................................................................... 7-10
Delete RF Device ...........................................................................................................................................................................................................7-11
Test RF Device ................................................................................................................................................................................................................7-11
GLOBAL INPUT OPTIONS .....................................................................................................................................................711
EOL Value .........................................................................................................................................................................................................................7-11
Keyswitch Options ........................................................................................................................................................................................................7-12
Input Options .................................................................................................................................................................................................................7-12
Input Type ........................................................................................................................................................................................................................7-13
Tamper Options .............................................................................................................................................................................................................7-13
INPUT TESTING ......................................................................................................................................................................714
Walk Test All Zones .......................................................................................................................................................................................................7-14
Walk Test A Single Zone .............................................................................................................................................................................................7-14
Sensor Watch Time .......................................................................................................................................................................................................7-14
SECTION 8
OUTPUT PROGRAMMING .......................................................................................................................81
OUTPUT COMMANDS .............................................................................................................................................................81
Output Status ................................................................................................................................................................................................................... 8-1
Turn Output On/O ....................................................................................................................................................................................................... 8-2
OUTPUT PROPERTIES .............................................................................................................................................................82
Output Name ................................................................................................................................................................................................................... 8-2
Event Type ......................................................................................................................................................................................................................... 8-3
Event Assignment ........................................................................................................................................................................................................... 8-7

Solution 16i  Installation Manual  Contents
vi Bosch Security Systems 09/11 BLCC500I
Output Polarity ................................................................................................................................................................................................................ 8-7
TIMED OUTPUTS .....................................................................................................................................................................89
Time Parameter ............................................................................................................................................................................................................... 8-9
Output Options ............................................................................................................................................................................................................... 8-9
Macro Group ...................................................................................................................................................................................................................8-10
OUTPUT TESTING ..................................................................................................................................................................810
External Siren Test .........................................................................................................................................................................................................8-10
Internal Bell Test ............................................................................................................................................................................................................8-10
Strobe Siren Test ............................................................................................................................................................................................................8-10
OUTPUT EVENT TYPES ..........................................................................................................................................................811
OUTPUT DEFAULT TABLE ......................................................................................................................................................811
SECTION 9
COMMS PROGRAMMING ........................................................................................................................91
COMMS PROGRAMMING COMMANDS .................................................................................................................................91
Domestic Number .......................................................................................................................................................................................................... 9-1
Call / Answer RAS ............................................................................................................................................................................................................ 9-2
Call Forward On/O ....................................................................................................................................................................................................... 9-2
Start Direct Link Session ............................................................................................................................................................................................... 9-2
Voice Setup ....................................................................................................................................................................................................................... 9-2
PHONE NUMBER PROGRAMMING ........................................................................................................................................93
Number Prex .................................................................................................................................................................................................................. 9-3
Primary Dest 1 .................................................................................................................................................................................................................. 9-3
Secondary Dest 1 ............................................................................................................................................................................................................ 9-3
Primary Dest 2 .................................................................................................................................................................................................................. 9-3
Secondary Dest 2 ............................................................................................................................................................................................................ 9-4
Domestic Number .......................................................................................................................................................................................................... 9-4
Call Forward On ............................................................................................................................................................................................................... 9-4
Example: ................................................................................................................................................................................................... 9-5
Call Forward O ............................................................................................................................................................................................................... 9-5
COMMS PROPERTIES ..............................................................................................................................................................95
Call Attempt Count ........................................................................................................................................................................................................ 9-5
Dialler Options ................................................................................................................................................................................................................. 9-6
Phone Line Options ....................................................................................................................................................................................................... 9-6
Country ............................................................................................................................................................................................................................... 9-7
Set SMS Password ........................................................................................................................................................................................................... 9-7
Call Back Number............................................................................................................................................................................................................ 9-8
RAS Security PIN .............................................................................................................................................................................................................. 9-8
Log Threshold .................................................................................................................................................................................................................. 9-8
Ring Count ........................................................................................................................................................................................................................ 9-9
Solution Link RAS Options ........................................................................................................................................................................................... 9-9
DTMF Options ................................................................................................................................................................................................................9-10
DTMF CONTROL FUNCTIONS ..............................................................................................................................................911
Voice Access Code ........................................................................................................................................................................................................9-12
CLI Number .....................................................................................................................................................................................................................9-12
REPORTING OPTIONS ...........................................................................................................................................................913
TX Format Dest 1 ...........................................................................................................................................................................................................9-13
TX Format Dest 2 ...........................................................................................................................................................................................................9-13
Test Route ........................................................................................................................................................................................................................9-13
Status Route ....................................................................................................................................................................................................................9-14
Emergency Route .........................................................................................................................................................................................................9-14
Swinger Dialler ...............................................................................................................................................................................................................9-14
Burg Report Delay ........................................................................................................................................................................................................9-14
Fire Report Delay...........................................................................................................................................................................................................9-15
COMMS REGISTRATION ........................................................................................................................................................915
MyAlarm IP Address .....................................................................................................................................................................................................9-15
MyAlarm Port .................................................................................................................................................................................................................9-15
MyAlarm Options ..........................................................................................................................................................................................................9-15
Email Address .................................................................................................................................................................................................................9-16
Email Options .................................................................................................................................................................................................................9-16
Base Station IP Address ..............................................................................................................................................................................................9-17
Base Station Port Number .........................................................................................................................................................................................9-17
Poll Rate ............................................................................................................................................................................................................................9-17

vii
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Contents
Acknowledge Wait Time .............................................................................................................................................................................................9-18
IP Format ..........................................................................................................................................................................................................................9-18
Retry Count .....................................................................................................................................................................................................................9-18
RAS IP Address ...............................................................................................................................................................................................................9-19
RAS IP Port .......................................................................................................................................................................................................................9-19
IP RAS Options ...............................................................................................................................................................................................................9-20
IP RAS Lockout Time ....................................................................................................................................................................................................9-20
COMMS TESTING ...................................................................................................................................................................921
Send Test Report ...........................................................................................................................................................................................................9-21
Test Report Time ...........................................................................................................................................................................................................9-21
Test Report Period ........................................................................................................................................................................................................9-21
Test Report Options .....................................................................................................................................................................................................9-22
Test Route ........................................................................................................................................................................................................................9-22
Dial Number Test ...........................................................................................................................................................................................................9-22
SECTION 10
DEVICE PROGRAMMING .......................................................................................................................101
DEVICE COMMANDS .............................................................................................................................................................101
LAN Status .......................................................................................................................................................................................................................10-1
LAN Secure ......................................................................................................................................................................................................................10-1
KEYPAD OPTIONS .................................................................................................................................................................102
Keypad Volume ..............................................................................................................................................................................................................10-2
Keypad Contrast ............................................................................................................................................................................................................10-2
Keypad Backlight ..........................................................................................................................................................................................................10-2
Home Area ......................................................................................................................................................................................................................10-2
General Options ............................................................................................................................................................................................................10-3
Beeper Options ..............................................................................................................................................................................................................10-4
Emergency Keys ............................................................................................................................................................................................................10-4
Access Group ..................................................................................................................................................................................................................10-5
Lockout Time .........................................................................................................................................................................................10-6
RF RECEIVER OPTIONS .........................................................................................................................................................106
Receiver Options ...........................................................................................................................................................................................................10-6
Supervision Time ..........................................................................................................................................................................................................10-6
RF Device Options ........................................................................................................................................................................................................10-7
Add RF Keypad ..............................................................................................................................................................................................................10-8
Delete RF Keypad ..........................................................................................................................................................................................................10-8
View RF Device ID .........................................................................................................................................................................................................10-8
SERIAL DEVICE OPTIONS .....................................................................................................................................................108
Device Type .....................................................................................................................................................................................................................10-8
Baud Rate .........................................................................................................................................................................................................................10-8
Flow Control ...................................................................................................................................................................................................................10-8
Report Format ................................................................................................................................................................................................................10-8
Options .............................................................................................................................................................................................................................10-8
ETHERNET DEVICE OPTIONS ...............................................................................................................................................109
IP Address Module ........................................................................................................................................................................................................10-9
Subnet Mask ...................................................................................................................................................................................................................10-9
Default Gateway ............................................................................................................................................................................................................10-9
MAC Address ..................................................................................................................................................................................................................10-9
Encryption Key ............................................................................................................................................................................................................ 10-10
IPRS Address (Reserved) .......................................................................................................................................................................................... 10-10
IPRS Port (Reserved) .................................................................................................................................................................................................. 10-10
Connetix NNC .............................................................................................................................................................................................................. 10-10
Ethernet Options........................................................................................................................................................................................................ 10-11
SECTION 11
SYSTEM PROGRAMMING ......................................................................................................................111
SYSTEM COMMANDS ............................................................................................................................................................111
Panel Status ....................................................................................................................................................................................................................11-1
System Trouble ..............................................................................................................................................................................................................11-1
History Log ......................................................................................................................................................................................................................11-2
System > Commands >...............................................................................................................................................................................................11-2
Domestic Default ..........................................................................................................................................................................................................11-2
Factory Default ..............................................................................................................................................................................................................11-2
Template Default ..........................................................................................................................................................................................................11-3

Solution 16i  Installation Manual  Contents
viii Bosch Security Systems 09/11 BLCC500I
Service Mode ..................................................................................................................................................................................................................11-3
SYSTEM CLOCK ......................................................................................................................................................................113
Set Date & Time .............................................................................................................................................................................................................11-3
Summertime On............................................................................................................................................................................................................11-4
Summer Time O ..........................................................................................................................................................................................................11-4
SYSTEM TIMERS .....................................................................................................................................................................115
Exit Time ...........................................................................................................................................................................................................................11-5
Entry Time 1 ....................................................................................................................................................................................................................11-5
Entry Time 2 ....................................................................................................................................................................................................................11-5
Part Entry Time...............................................................................................................................................................................................................11-5
Auto Arm Pre-Alert .......................................................................................................................................................................................................11-6
Output Pre-Alert ...........................................................................................................................................................................................................11-6
Senior Watch Time ........................................................................................................................................................................................................11-6
SYSTEM POWER OPTIONS ....................................................................................................................................................117
AC Options ......................................................................................................................................................................................................................11-7
Battery Options .............................................................................................................................................................................................................11-7
Fuse Options ...................................................................................................................................................................................................................11-8
HORN SPEAKER OPTIONS ....................................................................................................................................................119
Tone ...................................................................................................................................................................................................................................11-9
Speed ................................................................................................................................................................................................................................11-9
Volume (RF SPK Beep) .................................................................................................................................................................................................11-9
Siren Swinger .................................................................................................................................................................................................................11-9
SYSTEM SCHEDULES ...........................................................................................................................................................1110
Name .............................................................................................................................................................................................................................. 11-10
Start / Stop Times ....................................................................................................................................................................................................... 11-10
Day .................................................................................................................................................................................................................................. 11-11
Function ........................................................................................................................................................................................................................ 11-11
Index ............................................................................................................................................................................................................................... 11-12
SYSTEM HOLIDAYS ..............................................................................................................................................................1113
Name .............................................................................................................................................................................................................................. 11-13
Start / Stop Dates ....................................................................................................................................................................................................... 11-13
SYSTEM OPTIONS ................................................................................................................................................................1114
General Options ......................................................................................................................................................................................................... 11-14
Area Options ................................................................................................................................................................................................................ 11-14
Keypad Idle Screen .................................................................................................................................................................................................... 11-15
Keypad Hi/Lo Temp ................................................................................................................................................................................................... 11-15
Installer Options ......................................................................................................................................................................................................... 11-16
Language ...................................................................................................................................................................................................................... 11-17
Site Name ..................................................................................................................................................................................................................... 11-17
SYSTEM TESTING .................................................................................................................................................................1118
Walk Test All Zones .................................................................................................................................................................................................... 11-18
Battery Test ................................................................................................................................................................................................................... 11-18
SECTION 12
PROGRAMMING EXAMPLES .................................................................................................................121
SECTION 13
SPECIFICATIONS ....................................................................................................................................131
SPECIFICATIONS ....................................................................................................................................................................131
SECTION 14
INDEX ......................................................................................................................................................141

ix
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Contents
TABLES
TABLE 1: EXPANSION OPTIONS .............................................................................................................................................22
TABLE 2: DIALLER INDICATOR LED ........................................................................................................................................25
TABLE 3: STATUS INDICATOR LED .........................................................................................................................................25
TABLE 4: KEYPAD BUTTON FUNCTIONS ...............................................................................................................................25
TABLE 5: KEYPAD EMERGENCY ALARM TRIGGER’S .............................................................................................................26
TABLE 6: KEYPAD DIP SWITCH ADDRESS SETTINGS ...........................................................................................................26
TABLE 7: ICON & LED INDICATOR MEANINGS ......................................................................................................................27
TABLE 8: KEYPAD TONE MEANINGS ......................................................................................................................................27
TABLE 9: ZONE CONFIGURATION USING EXPANDERS ........................................................................................................29
TABLE 10: LAN MODULE ADDRESSING ...............................................................................................................................211
TABLE 11: EOL RESISTOR COLOUR CODES .........................................................................................................................211
TABLE 12: BOARD CONNECTOR DESCRIPTIONS ..................................................................................................................32
TABLE 13: TERMINAL BLOCK DESCRIPTIONS AND FUNCTIONS ........................................................................................32
TABLE 14: KEYS USED DURING PROGRAMMING .................................................................................................................41
TABLE 15: TEXT KEYPAD CHARACTER SET ...........................................................................................................................42
TABLE 16: PHONE NUMBER PROGRAMMING.......................................................................................................................43
TABLE 17: DOMESTIC DIALING DEFAULTS SETTINGS .........................................................................................................44
TABLE 18: DTMF REMOTE CONTROL FUNCTIONS ...............................................................................................................45
TABLE 19: BASIC REPORTING CODE REFERENCE .................................................................................................................46
TABLE 20: SYSTEM TROUBLE / FAULT DESCRIPTIONS .........................................................................................................48
TABLE 21: PROGRAMMING LOCATIONS AND DESCRIPTIONS .........................................................................................412
TABLE 22: USER DEFAULT PROGRAMMING OPTIONS .........................................................................................................52
TABLE 23: DEFAULT USER NAMES .........................................................................................................................................56
TABLE 24: DEFAULT AREA NAMES .........................................................................................................................................64
TABLE 25: ZONE CONFIGURATION ........................................................................................................................................71
TABLE 26: ZONE DEFAULTS ....................................................................................................................................................74
TABLE 27: DEFAULT ZONE NAMES .........................................................................................................................................74
TABLE 28: DEFAULT OUTPUT NAMES ....................................................................................................................................82
TABLE 29: EXAMPLE  OUTPUT ONE SHOT TIMER ...............................................................................................................89
TABLE 30: OUTPUT EVENT TYPES ........................................................................................................................................811
TABLE 31: OUTPUT DEFAULT TABLE ....................................................................................................................................811
TABLE 32: DTMF REMOTE CONTROL FUNCTIONS .............................................................................................................911
TABLE 33: KEYPAD EMERGENCY KEYS ................................................................................................................................105
TABLE 34: DAYLIGHT SAVINGS DATES  AUSTRALIA ........................................................................................................114
TABLE 35: DEFAULT SCHEDULE NAMES ............................................................................................................................1110
TABLE 36: DEFAULT HOLIDAY NAMES ...............................................................................................................................1113

Solution 16i  Installation Manual  Contents
xBosch Security Systems 09/11 BLCC500I
FIGURES
FIGURE 1: PCB AND MOUNTING CLIP INSTALLATION DIAGRAM ......................................................................................21
FIGURE 2: TAMPER BRACKET INSTALLATION .......................................................................................................................21
FIGURE 3: PCB MOUNTING CLIP ............................................................................................................................................22
FIGURE 4: MW700 CONFIGURATION EXAMPLES .................................................................................................................23
FIGURE 5: MW710  LARGE ENCLOSURE DETAILS ...............................................................................................................23
FIGURE 6: MW710 CONFIGURATION EXAMPLES .................................................................................................................24
FIGURE 7: INTERNAL TRANSFORMER CONNECTION DIAGRAM ........................................................................................24
FIGURE 8: KEYPAD EMERGENCY KEYS ..................................................................................................................................26
FIGURE 9: KEYPAD ADDRESS SELECTION ............................................................................................................................26
FIGURE 10: LCD DISPLAY SHOWING ALL ICONS ..................................................................................................................26
FIGURE 11: CP150B EXTERNAL VANDAL RESISTANT KEYPAD ...........................................................................................28
FIGURE 12: PR111B SLIM EXTERNAL LAN READER .............................................................................................................28
FIGURE 13: CM704B ZONE EXPANDER ..................................................................................................................................29
FIGURE 14: CM710B OUTPUT EXPANDER MODULE ............................................................................................................29
FIGURE 15: CM720B POWER SUPPLY MODULE....................................................................................................................29
FIGURE 16: CM195B MULTI RF RECEIVER INTERFACE MODULE .......................................................................................210
FIGURE 17: CM750B IP INTERFACE MODULE .....................................................................................................................210
FIGURE 18: CM101B VOICE MODULE ..................................................................................................................................210
FIGURE 19: EOL RESISTOR COLOUR CHART .......................................................................................................................211
FIGURE 20: N/C NO EOL ZONE ................................................................................................................................................31
FIGURE 21: N/C SINGLE EOL ZONE ........................................................................................................................................31
FIGURE 22: N/C SPLIT EOL ZONE ...........................................................................................................................................31
FIGURE 23: N/C ZONE WITH TAMPER ....................................................................................................................................31
FIGURE 24: N/O NO EOL ZONE ...............................................................................................................................................31
FIGURE 25: N/O SINGLE EOL ZONE ........................................................................................................................................31
FIGURE 26: N/O SPLIT EOL ZONE ...........................................................................................................................................31
FIGURE 27: N/O ZONE WITH TAMPER ....................................................................................................................................31
FIGURE 28: TERMINAL DESCRIPTIONS .................................................................................................................................33
FIGURE 29: WIRING DIAGRAM ...............................................................................................................................................34
FIGURE 30: LAN CONNECTION USING 2 PAIR SECURITY CABLE
RECOMMENDED FOR LAN LENGTHS 300 METRES OR LESS. ..............................................................................................35
FIGURE 31: LAN CONNECTION USING TWISTED PAIR CABLE
RECOMMENDED FOR LAN LENGTHS GREATER THAN 300 METRES. .................................................................................36
FIGURE 32: TEXT CHARACTERS WHICH CAN BE DISPLAYED. .............................................................................................42
FIGURE 33: SAMPLE OPTION BIT MENU DISPLAY ...............................................................................................................42
FIGURE 34: AREA TEXT PROGRAMMING DISPLAY ..............................................................................................................42
FIGURE 35: TELEPHONE NUMBER PROGRAMMING DISPLAY ............................................................................................43
FIGURE 36: LIST OPTION PROGRAMMING DISPLAY ...........................................................................................................43
FIGURE 37: FACTORY DEFAULT DISPLAY ..............................................................................................................................44
FIGURE 38: ZONE ARRAY SHOWING Z1 TO Z4 .....................................................................................................................46
FIGURE 39: ZONE ARRAY SHOWING Z9 TO Z12 ...................................................................................................................46
FIGURE 40: SYSTEM TROUBLE DISPLAY SEQUENCE............................................................................................................47
FIGURE 41: TEXT MENU EXAMPLES ......................................................................................................................................49
FIGURE 42: KEYPAD EMERGENCY KEYS ..............................................................................................................................105

1-1
Bosch Security Systems 09/11 BLCC500I
SECTION 1
Overview
FEATURES
Listed below are the main features of the Solution 16i Control Panel.
Individual Box Tamper Circuit Monitoring
Telephone Line Busy Tone Detect
RAS Intelli-connect® CLI Caller Line Identication
Daylight Savings Auto Time Adjust
Senior Watch
System Maintenance Interval Reminder
System Weekly Test Reminder
Area Inactivity Interval
Temporary Pin Code
Dual Reporting
Alarm Report Abort/cancel Options
8 Programmable Holiday Calendars
8 Programmable Schedules
8 On-board Zones (Exp To 16 Wired or Wireless)
Fire Alarm Verication
48 PIN’s
4 Supervised High Power Digital Outputs
Supervised Siren Driver
Partitionable To 4 Areas
Reports SIA, Contact ID, IP, SMS, Voice and Email Formats
Supervised LAN Keypads (Maximum 8 Keypads)
Keyswitch Input
256 History Event Memory
Fully Menu Text Programmable
Programmable Via Solution Link (Remote/Direct)
Telephone Line Fail Monitor
Time Executed Functions
60 Output Event Types
Exit Restart
Expansion Module SuperSolution
DTMF Tone Decoder Built In
Remote and Auto Arming

1-2 Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Overview
O V E R V I E W
Zones
The control panel provides up to 16 separate zones of
protection. Zone programming determines the panel’s
response to open/short and tamper conditions on the
zone loop.
Areas
The control panel supports up to 4 separate areas. You
can assign all zones to a single area, or you can assign
each zone to a combination of dierent areas.
You can arm and disarm the control panel by area,
alternatively, you can arm and disarm several areas at the
same time.
Dialler
The control panel has a built-in dialler to send reports
to the receiving party (ie. Security company monitoring
station, mobile phone, SMS etc).
Keypads
You can connect a maximum of 8 fully supervised keypads
to the control panel. Proximity keypads and external
vandal resistant metal keypads (CP150B/CP151B) are also
available.
LAN Readers
External LAN readers (PR109B Black/PR110B White and
slim PR111B Black/PR112B White) feature our proprietary
40 bit transmission format and can be used to provide
alarm and or access control functionality when used on
the Solution 16i security control panel.
IP Reporting
The CM750B Ethernet Module allows you to interface the
control panel to the building’s hard wired IP connection
point using a CAT 5E connection cable. Once congured
and operating you will be able to report to monitoring
centres that support the available IP reporting formats
and to upload/download to the control panel through an
internet or intranet connection.
History Log
The control panel can store up to 256 history events from
all 4 areas. All events are stored in the log, even if they are
programmed not to report via the on-board dialler.
You can view the control panel’s history log via keypad,
or by connection of a personal computer (direct/remote)
using the Solution Link upload/download software.
Programming
You can program the control panel either by a keypad
or using a personal computer using the Solution Link
upload/download software.
Solution Link Version V1.10 or higher is required to
program this panel.

2-1
Bosch Security Systems 09/11 BLCC500I
SECTION 2
Installing the Hardware
ABOUT THE PANEL
ENCLOSURES
The MW700 - Small Enclosure and MW710 - Large
Enclosure have been designed to reduce installation time
and improve aesthetics on larger installations where often
multiple enclosures need to be located in close proximity
to each other.
A number of new features have been incorporated
including a new style tamper bracket which can be
easily installed before or after the enclosure is mounted
to the wall, an anti tamper lid which insures the cabinet
tamper triggers when the lid is removed, easier access
for exible and rigid conduits, additional 20mm cable
entry knockouts and a new board mounting system using
removable spring clips.
The MW700 and MW710 enclosures include numerous
holes, allowing the PCB mounting clips to be positioned
in the most appropriate location for each installation.
i
Note
For ease, it is recomended that the PCB mounting
clips are installed from the rear of the enclosure
before mounting it to the wall.
Circuit Board
Component Side
Rear of Cabinet
3mm Philips Head
Machine Screw
Supplied
Support Clip
Press Fit Supplied
Figure 1: PCB and Mounting Clip Installation Diagram
ENCLOSURE FIXING METHOD
MW700 - Small Enclosure
Use appropriate fasteners capable of handling a minimum
of 6kg to x the cabinet against a sturdy surface using the
mounting holes provided.
MW710 - Large Cabinet
Use appropriate fasteners capable of handling a minimum
of 12kg to x the cabinet against a sturdy surface using
the mounting holes provided.
INSTALLING THE TAMPER SWITCH
The tamper switch can be located on either the left or right
hand side of the cabinet to suit the installation. Before
installing the bracket, t the tamper lead to the switch
and then insert it into the bracket.
Once the enclosure has been mounted to the wall, insert
the tamper bracket into the rectangular hole in the top
ange of the enclosure and then slide the base of the
bracket toward the top until the tamper switch locates in
the rear of the enclosure.
Depress the tamper a few times with your nger to ensure
smooth operation.
Figure 2: Tamper Bracket Installation
ENCLOSURE MODULE SPACES
The MW700 enclosure has space for 2 large modules or
4 small modules while the optional MW710 enclosure
has space for up to 4 large modules or 8 small ones. The
enclosures have been designed so that any combination
of large and small units can be neatly mounted together
on the wall.
Each module is mounted to the enclosure using 4 or more
clip in standos. The clips can be inserted from the rear
of the enclosure before mounting it to the wall, or from
the front of the enclosure after it has been mounted. Both

2-2 Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Installing the Hardware
methods should be performed using your nger tips to
prevent damage to the stando. (Standos and screws
are supplied with each module).
All compatible add on modules will mount on these
spaces. See below for list if modules which can be added
to the Solution 16i control panel.
Module Space Occupied
Solution 16i Control Panel 2 Module Spaces
CM704B Zone Expander 1 Module Space
CM710B Output Expander 1 Module Space
CM720B LAN Power Supply 1 Module Space
CM195 RF Receiver Expander 1 Module Space
Table 1: Expansion Options
Use the above table to help determine which size cabinet
you will require for the job.
On some export models, one module space will not be
available as the mains transformer mounts in this location.
INSTALLING PANELS AND MODULES
Once the enclosure is secured in place, install the panels
and modules onto the mounting clip using the supplied
3mm screws. Do not over tighten the screws.
When tting panels or large modules, you should use 5
mounting clips, one in each corner of the PCB and one
in the middle of the PCB underneath the main terminal
blocks. When mounting small modules, only 4 clips are
required, 1 in each corner.
Both enclosures are supplied with tamper switches,
tamper leads, tamper brackets and a quantity of
mounting clips and screws. If required, additional
mounting clips and screws may be purchased in bags of
50 clips (10 packs x 5pcs). (P/N: MW890)
i
Note
The supplied mounting clips are designed to use the
3mm machine screws supplied with the enclosure.
The use of self tapping screws will damage the clips.
320 mm
260 mm
A AAA
A
AAA
CABLE ENTRY (REAR)
A A
AA
AAAA
A= PCB Mounting Clip Holes
C C
BB
B
B
D
= Enclosure Mounting Holes
B
= Tamper Bracket Mounting Holes
C
= Earth Stud - 4mm
D
Figure 3: MW700 - Small Enclosure Details
Figure 3: PCB Mounting Clip
The following example shows the MW700 -Small enclosure
congured using 4 small modules.

2-3
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Installing the Hardware
CABLE ENTRY (REAR)
MODULE
SPACE 1
MODULE
SPACE 4
MODULE
SPACE 2
MODULE
SPACE 3
CABLE ENTRY (REAR)
MODULE
SPACE 1
MODULE
SPACE 3
MODULE
SPACE 2
When installing small modules, you should
fit 4 mounting clips as shown.
12
3
4
12
3
45
When installing large modules, you should
fit 5 mounting clips as shown.
Clip 5 provides support under the main
terminal block only. No screw is fitted.
Figure 4: MW700 Conguration Examples
320 mm
520 mm
A A
AA
AAAA
A AAA
A
AAA
A AAA
A
AAA
A AAA
A
AAA
CABLE ENTRY (REAR)
CABLE ENTRY (REAR)
CABLE ENTRY (REAR)
A= PCB Mounting Clip Holes
= Enclosure Mounting Holes
B
= Tamper Bracket Mounting Holes
C
= Earth Stud - 4mm
D
C C
BB
D
BB
D
D
Figure 5: MW710 - Large Enclosure Details
The following examples show the MW710 - Large
enclosure congured using 6 small modules and 1 large
module.

2-4 Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Installing the Hardware
CABLE ENTRY (REAR)
MODULE
SPACE 1
MODULE
SPACE 3
MODULE
SPACE 2
MODULE
SPACE 5
MODULE
SPACE 4
MODULE
SPACE 7
MODULE
SPACE 6
CABLE ENTRY (REAR)
CABLE ENTRY (REAR)
When installing small modules, you should
fit 4 mounting clips as shown.
When installing large modules you should fit 5
mounting clips as shown.
Clip 5 provides support under the main terminal
block only. No screw is fitted.
12
3
45
12
3
4
Figure 6: MW710 Conguration Examples
CONNECTING POWER TO THE PANEL
For normal operation, the panel requires both AC and DC
power sources. The AC source can be provided either
by an external adapter or by an internal transformer
depending on the model and country of sale.
When connecting using the A.C adapter, feed the cable in
to the enclosure and terminate the wires on the removable
terminal block supplied before connection it to the PCB.
If using a 3 wire Adaptor, then the earth wire should also
be terminated onto the terminal block. Always check the
orientation of the terminal block with the PCB markings
before connecting it to the PCB.
CO N N EC T I N G T H E B AT TE RY
The panel is supplied with a set of battey leads to suit
the chosen enclosure. Connect the Red Battery lead to
the Battery (+) terminal and the Black Battery lead to the
Battery (-) terminal on the PCB.
Once terminated onto the PCB connect the other end of
the leads to the battery paying attention to the polarity.
AC MAINS TRANSFORMER OPTION
On models with an internal transformer, a permanent
connection shall be made to the mains supply. See
Figure 8. This must be completed by a suitably qualied
electrician according to the applicable wiring standards
and regulations.
Next connect the transformer output wires (red) to the
removable terminal block supplied and then connect it
to the PCB. Always check the orientation of the terminal
block with the PCB markings before connecting.
i
Note
For permanently connected equipment, a readily
accessable disconnect device shall be installed in a
location near to the equipment.
A
A
A A
TRANSFORMER
FUSE
220 - 240V A.C.
50-60Hz 150mA
8AG - 250V
250mA MAX
NEUTRAL
EARTH
ACTIVE
FUSED
L N
L
N
C
Transformer Output
(Red Wires) Wiring must be carried out by
a licensed electrician following
applicable wiring standards
Transformer
Input
(Blue Wires)
A = PCB Mounting Clip Holes
B
D
= Enclosure Mounting Holes
B
= Fused Terminal Block
C
= Transformer
D
Figure 7: Internal Transformer Connection Diagram

2-5
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Installing the Hardware
PANEL LED INDICATORS
The control panel PCB has two LED indicators (Dialler and
Status LED’s) which display the following information.
Condition Meaning
O Oine
On On Line (Dialling/
Answered)
Flashing Incoming Call
Table 2: Dialler Indicator LED
Condition Meaning
O Error
On Error
Flash Once Every 2 Seconds OK
Flash Fast AC or Battery Trouble
Table 3: Status Indicator LED
i
Note
During factory defaulting the Status and Dialler LED
indicators will ash alternatively for approximately
15 seconds.
KEYPAD BUTTON FUNCTIONS
The keypad has 20, silicone rubber push button keys. The
keyss allow you to input instructions and navigate the
menu screens as required. Some buttons have a secondary
function which is activated by holding them down for two
seconds.
Each key’s function is described below
Key Description
to
The numeric keys allow you to enter
numbers when required
Use the [MENU] and the numeric
keys to enter commands. The
[MENU] key is also used to go back
one level when navigating through
menus or to exit a programming
location without saving changes.
The [ON] key allows you to turn an
area or output on. To turn all areas
on at the same time when the system
has been partitioned, press and hold
the [ON] key for two seconds.
The [PART] key allows you to turn an
area Part On. This key can also be
used to bypass a zone or multiple
zones when you press and hold for
two seconds.
Key Description
The [OFF] key allows you to turn an
area or output o. To turn all areas
o at the same time when the system
has been partitioned, press and hold
the [OFF] key for two seconds.
The [OK] key allows you to save any
changes and exit the command.
The [MAIL] key allows you to read
stored mail. This key can also be
used to initiate a dialler test when
you press and hold for two seconds.
The [] key allows you to move the
cursor to the left when programming
text or telephone numbers.
The [] key allows you to move
the cursor to the right when
programming text or telephone
numbers.
The [↑] key allows you to navigate
through menus or to toggle
characters when programming text
or telephone numbers.
The [] key allows you to navigate
through menus or to toggle
characters when programming text
or telephone numbers. Pressing the
[] key when the area is disarmed
will display any current trouble
conditions.
+
for 2 sec
Pressing the [] and [↑] keys
together and holding them down for
2 seconds will trigger a Panic alarm.
If programmed the sirens will sound
and the monitoring station will be
notied.
+
for 2 sec
Pressing the [] and [] keys
together and holding them down
for 2 seconds will cause trigger a Fire
alarm. If programmed the sirens will
sound and the monitoring station
will be notied.
+
for 2 sec
Pressing the [↑] and [] keys together
and holding them down for 2
seconds will trigger a Medical alarm.
If programmed the sirens will sound
and the monitoring station will be
notied.
Table 4: Keypad Button Functions

2-6 Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Installing the Hardware
Figure 8: Keypad Emergency Keys
KEYPAD EMERGENCY ALARM TRIGGER’S
Key Sequence Event Triggered
[←] + [→] Hold for 2 seconds Keypad Fire Alarm
[→] + [↑] Hold for 2 seconds Keypad Panic Alarm
[↑] + [↓] Hold for 2 seconds Keypad Medical Alarm
Table 5: Keypad Emergency Alarm Trigger’s
K E Y PAD S E T U P
The Solution 16i control panel can have a maximum of 8
keypads connected via the LAN terminals. Each keypad
must be set to a unique address before they will operate.
Each keypad needs to be assigned to a home area via
MENU 6-1-3. This sets the area the keypad will display and
control by default. Keypads can be locked to a home area
or allowed to roam or move between areas.
When the system is powered up, any keypads which have
not been assigned a home area will be automatically set
to home area 1.
Set each keypad address using the table below as a guide.
i
Note
Only 1 Keypad can be assigned to each address. All
Keypads are supplied from the factory set to address
1. (OFF-OFF-OFF-OFF).
KEYPAD ADDRESS SELECTION
4
Figure 9: Keypad Address Selection
Keypad DIP Switch Address Settings
Keypad To
Address S1 S2 S3 S4
Keypad 1 O O O O
Keypad 2 On O O O
Keypad 3 O On O O
Keypad 4 On On O O
Keypad 5 O O On O
Keypad 6 On O On O
Keypad 7 O On On O
Keypad 8 On On On O
Table 6: Keypad DIP Switch Address Settings
S TATU S I CO N S & L ED I N D I C ATO RS
The following table lists the function of each of the ICON
Symbols and LED Indicators on the ICON Keypad Display.
Figure 10: LCD Display Showing All ICONs
Icon Status Meaning
AREA
The keypad can display which areas (1 – 4) are
turned on or o via the Area Icon Indicators.
This programmable option can be disabled in
MENU 6-1-4.
On Area is turned All On or Part On
O Area is turned O
Flashing
Fast Alarm occurred in the area
POWER
On System power is normal
Flashing System power is missing
FIRE
Flashing A re alarm is active
O No re alarm
On Fire alarm in memory (Turn the
area All On and O to Clear).
!
SERVICE
On
The existing service or trouble
condition has been acknowl-
edged.
O No service or trouble conditions
exist
Flashing
A service or trouble condition
is present that has not been
acknowledged.
M
PART
On The area is turned Part On.
O The area is not turned Part On.

2-7
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Installing the Hardware
OFF
On The area is turned O
O The area is turned All On or Part
On
ON
On The area is turned All On
O The area is turned O
(
()
)
CHIME
On Chime Mode is On
O Chime Mode is O
PHONE
On Phone Line in Use
O Phone Line not in use
Red LED
On System Armed
Flashing Alarm
Green
LED
On System Disarmed
Flashing Area not ready to turn on
Red &
Green
LED
Flashing Installer programming mode is
active.
9 10
11 12
13 14
15 16
1 2
3 4
5 6
7
8
On Zone Open or Unsealed
O Zone Closed or Sealed
Flashing Zone in Alarm or Alarm Memory
Table 7: ICON & LED Indicator Meanings
K E Y PAD TO N E S
Your keypad emits several distinct tones and displays text
to alert you to system events. The volume of the keypad
tones can be adjusted in MENU 6-1-0.
Type Meaning
Fire
Alarm
Tone
When a re zone sounds an alarm, the
keypad will sound 3 seconds on and 2
seconds o (repeat).
Burglary
Alarm
Tone
When a burglary zone activates while your
system is turned on, your keypad emits a
continuous siren tone. It sounds for the
time set by your security company.
Trouble
Tone
When a system component is not
functioning properly, your keypad sounds
4 fast short beeps followed by a 5 second
pause (repeat).
Key Press
Tone
Pressing any key on the keypad sounds
one short beep, indicating that the key
press is accepted.
Type Meaning
Entry
Delay
Tone
When you enter the premises through
a zone programmed for entry delay, the
keypad sound a Hi/Low tone to remind
you to turn o the area. If the area is not
turned o before the entry delay expires,
an alarm condition will sound and a report
may be sent to your alarm company.
Exit
Delay
Tone
After you turn an area All On, the keypad
will sound 1 short beep every second.
During the last 10 seconds fast short beeps
will be heard. If you don’t exit before the
delay time expires and an exit delay door
is faulted, an alarm occurs.
Error
Tone
If you press an incorrect key, your keypad
will sound a 2 second tone.
Menu
Mode
The keypad will sound a Hi / Lo tone to
indicate you have entered MENU Mode
and a Lo/Hi tone to indicate you have
exited MENU mode.
Chime
Tone
The keypad sounds fast short beeps to
alert you when a zone programmed for
chime is faulted or unsealled.
Table 8: Keypad Tone Meanings

2-8 Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Installing the Hardware
VANDAL RESISTANT KEYPADS
The CP150B keypad provides alarm and or access control
functionality when used on selected Solution security
control panels. Constructed from satin chrome plated
zinc die cast, the CP150B/CP151B (slim) keypad provides a
high level of vandal resistance and is also weather resistant
to IP67 making it ideal for external installations.
Both keypads includes red and green indicators which are
used to show area or door lock status and the 12 buttons
with blue backlighting make it easy to operate in all
lighting conditions.
The keypad connects to the control panel via the RS485
encrypted LAN and occupies a standard keypad position
in the panel conguration.
Figure 11: CP150B External Vandal Resistant Keypad
WATERPROOF EXTERNAL LAN READERS
The PR109B (Black)/PR110B (White) and the slim PR111B
(Black)/PR112B (White) external LAN readers feature our
proprietary 40 bit transmission format and can be used
to provide alarm and or access control functionality when
used on selected Solution security control panels.
Constructed from UV stabilised ASA plastic, the external
readers provide a high level of vandal resistance and are
weather resistant to IP66 making them ideal for outdoor
installations.
The LAN readers include red, green and blue indicators
which are used to show area and or door lock status at all
times.
The reader connects to the control panel via the RS485
encrypted LAN and occupies a standard keypad position
in the panel conguration.
Figure 12: PR111B Slim External LAN Reader