Bristan CRZ SHXDIVCTFF BLK (D1) Wiring diagram

2
5
Identify the
required position of
the valve and prepare
the water supply pipes.
Supply pipes should be
150mm apart.
Using the rubber fixing
plate supplied with the
wall mount, mark and
drill holes.
Secure the isolatorSecure the isolator
onto the backplateonto the backplate
ensuring the olive isensuring the olive is
positioned over thepositioned over the
pipework correctly.pipework correctly.
Push shrouds to thePush shrouds to the
back of the wall outlet,back of the wall outlet,
securing them againstsecuring them against
the rubber fixing plate.the rubber fixing plate.
4
3
1
1/2”
Compression
Installation
150mm Centres
Rotate the shroud until the opening alignsRotate the shroud until the opening aligns
with the isolation screw.with the isolation screw.
Turn the screw to isolate the water.Turn the screw to isolate the water.
Reverse the process when turning theReverse the process when turning the
water back on.water back on.
12
Secure the rubber backplateSecure the rubber backplate
and backplate into place.and backplate into place.
Secure the shower toSecure the shower to
the wall mount.the wall mount.
21mm21mm
Operation
IMPORTANT
Pack Contents
150mm
Centres
1.0
5.0
Pressure
BAR
0.2
4.0
2.0 3.0
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0 60°C
65°C
Specifications
Maximum Static Pressure: 10.0 bar
Inlet Water Temperature
Inlet Connections
Min: 1.0 bar Max: 5.0 bar
Working Pressures
The inlet hot water must
be at least 10°C above the
required blend temperature.
Factory pre-set
38°C
Inlet Dimensions
5°C
25°C
Cold Water Supply
Min: 5°C Max: 25°C
Hot Water Supply
Tools You’ll need
Flat head Screwdriver Cross head Screwdriver Hexagonal Keys
Pipe Cutter
Pencil Drill Spanner
Installation Instructions
& User Guide
Please leave these instructions
with the end user
Product Code: CRZ SHXDIVCTFF BLK (D1)
All products manufactured and supplied by Bristan are safe to use provided that
they are installed, operated and receive regular maintenance in
accordance with these instructions.
This product needs to be installed in accordance with, and meet the
requirements of the Water Supply (Water Fittings) Regulations 1999 and
current by-laws. For full Installation Requirements & Notes (IRN) please
visit wras.co.uk/directory.
Isolation valves must be fitted to the inlet water supplies to ensure ease of future
maintenance.
Before installing this product the water supply must be thoroughly flushed in
order to remove any swarf, solder etc.
This product must not be modified in any way as this will invalidate the
guarantee.
Full access must be made available for future maintenance/servicing purposes.
Before drilling into walls, check that there are no hidden electrical wires,
cables or water supply pipes. This can be checked with the aid of an
electronic detector.
If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
If in doubt, contact a registered plumber or your Local Water Authority or
the Secretary of the Institute of Plumbing, address as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: [phone]
Prior to Installation
60-65°C Recommended
REMEMBER
hot on the left,
cold on the
right
Safety Glasses Detector
On - FixedOn - Fixed
HeadHead
On -On -
HandsetHandset
HotHot
ColdCold
Remove the concealingRemove the concealing
cap from the shroud.cap from the shroud.
Isolation
x2 x2
x2
x2
x8
x8
x2
x2
x2
x2
x4
x1
x1
x1
x1
x1
x
1
x1
x1
x1
To replace any spare parts for
your shower why not scan the
below QR Code and search for
your product.
Spare Parts
REMEMBER
To service
your
product!
General Cleaning
Bristan products are made from premium
materials, with hand polishing and
electroplated, PVD or EPD finishes’
Your taps or shower should be regularly
cleaned with warm water, a mild pH-neutral
liquid soap, and polished with a soft cloth.
Any residues from soap, toiletries etc. should
be rinsed o straight after use.
Household bleaches and cleaners contain harsh
chemicals and may damage the surface finish.
Avoid using abrasive cloths, scouring pads,
scrub sponges, steel wool or anything similar.
Hole size
5.5mm

4
1
56
4
4
2
1
Remove
temperature
handle.
Turn flow handle to ‘on’
position, letting the
temperature stabilise.
Turn cartridge spindle clockwise
to decrease the temperature.
Turn cartridge spindle
anti-clockwise to increase the
temperature.
3
2
5
Troubleshooting
To reduce the build up of limescale and to ensure this shower works to its maximum performance we recommend
this shower is serviced every 6-12 months depending on the hardness of your water.
Servicing Intervals
Temperature Setting
Maintenance - Cartridge Cleaning
3
1
6
Symptom Cause Remedy
No flow or
low flow rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on and o as
flow rate or pressure is too low.
Increase water flow rate or pressure through system.
Head of water is below the minimum
distance required.
2 meters minimum required.
Hot or cold water being drawn o elsewhere
causing pressure changes or instantaneous
boiler temperature changes.
Do not use other water outlets when using the shower.
Airlock or partial blockage in the supply pipe
work.
Flush through pipe work to ensure removal of debris and any airlocks.
Water
dripping
from shower
This is normal for a short time after using the
shower.
This is caused by residual water tension, the build up of water in the shower.
If water continues to drip, possibly due to the
cartridge
Remove cartridge and clean, refer to 'Maintenance' section before starting any maintenance.
Maximum
Water
Temperature
too Hot/Cold
Maximum Water Temperature needs adjusting. Refer to the Temperature Setting section to set your desired maximum temperature.
Riser Installation 23
Press & hold
knob on the
bracket to
slide up or
down.
Using a spirit level
to ensure the riser is
positioned correctly
and perpendicular
to the wall, use the
assembled riser to
mark the desired
position of the bracket.
Drill holes. Secure the
bracket to the wall.
Secure the riser
bracket and
riser rail.
Attach the fixed head.
To adjust height of
head between 50-
410mm twist the knob
and slide the riser to
desired height.
Slide the
bracket onto
the riser rail,
then push the
riser extension
onto the riser
rail.
Tighten grub
screws at the
back.
To adjust the
height untighten
and move the arm
to the desired
height then
tighten again to
secure in place.
12
Reverse steps 1-2 to
reinstall the cartridge
and handle.
Remove O-rings
and soak all
components in
de-scaler and wash
o in clean water.
Examine all seals
and replace if need-
ed.
Use WRAS
approved silicon
based grease on all
seals.
12
7
REMEMBER
To service
your
product!
8
Remove
temperature
and flow
handle.
Remove
nut and
flow
valve.
ReplaceReplace
cartridge andcartridge and
turn spindleturn spindle
anti-clockwiseanti-clockwise
to maximumto maximum
temperature.temperature.
Replace
temperature stop,
ensure the raised side is
facing towards the back
of the valve.
Turn cartridge spindle clockwise to
decrease the temperature. Turn
cartridge spindle anti-clockwise to
increase the temperature.
Reverse steps
1-2 to reinstall
the valve and
secure handles.
Remove
temperature stop,
and cartridge.
At Bristan, we want to make things as easy as possible for our customers. That’s why we oer
solid guarantees on all our products, eective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register.
For any other queries, please call our Customer Service on 0330 026 6273
where our expert team of advisors will be able to oer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service-centre/guarantees.
Customer Service: [phone]
Web: www.bristan.com
Email: [e-mail]
A Masco Company
Bristan Group Ltd.
UK: Bristan Group, B78 1SG.
EU: Masco Europe S.à.r.l., 14 Rue Strachen
6933 Mensdorf, Luxembourg.
Our Guarantee
IMPORTANT
Isolate the
water supply
before
starting!
3mm
Hole size
5.5mm