Bticino CLASSE 300V13E User manual

Installation Manual
Classe 300
www.bticino.com

Classe 300
Installation Manual

3
Classe 300
Installation Manual
General information 4
Warnings and recommendations 4
Front view 4
Rear view 6
Dimensional data and installation heights 7
Wall-mounted installation 8
Installation on the table-top base 9
Physical configuration 10
Configurators 11
Functions of the M units configurator (Favorites key) 12
Functions of the M tenths configurator (Quick actions) 13
First switching on 17
Settings 19
General settings 19
Ringtones 22
Display 23
Answering machine (only for item 344622) 25
Quick actions 27
Configuration 29
Advanced Configuration 31
First switching on 31
Configuration 34
General settings 35
Intercom 35
Camera 37
Activation 39
Change password 41
Quick actions 42
Factory configuration 44
Contents

Classe 300
Installation Manual
4
General information
1. 7” touch screen display (16 : 9)
2. Screen OFF key
3. Time and date
4. Ringtone exclusion
5. Professional Studio (Office) activation
6. Microphone
7. Answering machine activation (only models 344622)
8. Quick actions
9. Tactile guides
10. Connection key:
The green LED flashes to indicate an incoming call
The green LED comes on steady to indicate that there is an active call
11. Auto-switching on/Scrolling:
the red LED turns on when the key is pressed
Warnings and recommendations
Front view
It is important to read this manual carefully before proceeding with the installation.
The guarantee automatically expires for negligence, misuse, tampering by unauthorized
personnel.
The Classe 300 Video internal unit must only be installed indoors; it must not be exposed to water
drops or splashes; it must be used only on BTicino 2 wire digital systems.
The image shows the device with all its functions enabled.
Check on the installer manual how to enable the functions.
Quick Actions
10:36
Tuesday, 22 April
Activations
Answering machine Cameras Memo
Settings
Intercom
Private camera
Lock
External intercom
Pager
6
10
1112139 9
16
17
15
14
3 4 5 721
8

Classe 300
Installation Manual
5
12. Favorites key:
the red LED turns on when the key is pressed
(Basic configuration = STAIRCASE LIGHT. For a different configuration refer to the physical
configuration table)
13. Door lock release key:
the red LED turns on when the key is pressed
14. Answering machine Status (only models 344622):
Red LED steady = answering machine active
Red LED flashing = new recording/s
15. Message status:
Red LED flashing = new unread note/s
16. Bell exclusion Status:
Red LED on = Call ringtone disabled
17. Functions (only the icons for the configured functions are displayed)

Classe 300
Installation Manual
6
1. Configurator socket
2. Configurator J1: remove for additional power supply
3. J2 configurator: Master/Slave, remove for Slave
4. Line termination ON/OFF micro-switch
5. Mini USB socket for device Firmware update using the MyHomeSuite software
Note: the device must be powered (1-2 or BUS)
6. Loudspeaker
7. Additional power supply clamps (1 - 2)
8. 2 WIRE SCS/BUS connection clamps
9. Clamps ( ) for the connection of an external call to the floor pushbutton
10. Additional ringtone connection clamps (1 - 5M)
Point-to-Point connections are required on the clamps of the additional ringtones
Rear view
78910
6
1
6
4
5
2 3

Classe 300
Installation Manual
7
Dimensional data and installation heights
160 – 165 cm 135 – 140 cm
25 mm
194 mm
162 mm
Quick Actions
10:36
Tuesday, 22 April
Activations
Answering machine Cameras Memo
Settings
Intercom
Private camera
Lock
External intercom
Pager
Height recommended, unless otherwise required by the law

Classe 300
Installation Manual
8
Wall-mounted installation
1
2
3
4

Classe 300
Installation Manual
9
Installation on the table-top base
Warning: position the microswitch on ON to terminate the line.
5 6 7 8
1
2
3
4
5
6
7
8
BUS
1-2
5 6 7 8
1
2
3
4
5
6
7
8
BUS
1-2
8-way socket:
336982/83/84 Livinglight
349414/15/18 Axolute
Quick Actions
10:36
Tuesday, 22 April
Activations
Answering machine Cameras Memo
Settings
Intercom
Private camera
Lock
External intercom
Pager

Classe 300
Installation Manual
10
Physical configuration
The device must be configured both physically or in advanced mode, the main differences are
shown in the following table:
Warning: the connection of the configurators to the N - P - M sockets precludes the
possibility of using the advanced configuration.
Available Functions Physical Configuration Advanced Configuration
FAVORITES KEY
Possibility of assigning various functions
See “Functions of the M units
configurator (Favorites key)”
Staircase Light function
QUICK ACTIONS
Private camera
Lock
External intercom
Pager
Preset:
See “Functions of the M tenths
configurator (Quick actions)”
The user can rename, delete and add
back, only the preset functions
Creating quick actions of all
functions
The user can decide the quick
actions to display in the home
page
FUNCTIONS
Cameras
Intercom
Activations
The use of the functions is only available
through quick actions in the home page
See “Functions of the M tenths
configurator (Quick actions)”
Dedicated icons in the home
page and customisable,
configurable functions
See “Configuration”
The configuration must be performed with the device disconnected from the power supply.
Before using it, wait for the LEDs to stop flashing.