BullFrog 6002 LETTO User guide

ASSEMBLY AND INSTRUCTION MANUAL
www.bullfrog-design.com
MODEL 6002 LETTO
© 2015 K URT BEI E R &KATI QU I N G E R
REMOVABLE SLIP COVER
WITHOUT ZIPPER
REMOVABLE SLIP COVER
WITH ZIPPER
HIGH-QUALITY
FUNCTIONAL BACK

6002 LETTO
© 2015 K URT BEI E R &KATI QU I N G E R
CONTENTS
2 side panels, 1 foot part (semi-product)
1 headboard (complete covered)
11 loose slip cover for corpus of bed
40 hexagon socket countersunk screws
4 corner connectors (2 x le side, 2 x right side)
1 beech woodcentre support rail with angle support
4 slatted frame angles for corner connectors
2 slatted frame angles for side panels
4 wooden feet
1 plastic supporting foot (120-235 mm)
1 allen key
2 plastic supporting foot (mounted)
8 felt gliders (glued)
T
T
Assembly manual
ATTENTION! To ensure secure assembly, please observe the
individual steps of instruction!
The furniture should always be mounted in pairs (2 persons)!
2. For assembly of bed, headboard and foot part
or rather the 2 side panels should be placed at
opposite side. The bores should point inwards.
1. Unpack the individual parts of the bed, place them as shown at picture
and check the delivered package contents for completeness.

6002 LETTO
© 2015 K URT BEI E R &KATI QU I N G E R
Bottom side
3. Place each of the T-shaped
punch-outs of connector angles
towards the side panels. Now fix 2
angles at headboard and 2 angles at
foot end of side panels. Slightly screw the
bolts by hand and then tighten them with
the Allen key.
Attention!
There are right- and le angles.
4. Set up one of the side panels and
position it orderly at angle. Setzen First
of all, place the 2 outer screws and
slightly tighten them. Now it will be easier
to place the other screws. Revise these
steps with the other side panel.
5. Next position the foot part and screw
it such as point 4.
6. Screw in the 4 wooden feet into the
threaded holes of connector angles.
7. Press the supporting foot into the hole
of centre support rail from below.

6002 LETTO
© 2015 K URT BEI E R &KATI QU I N G E R
8. Mount centre support rail at connectors of headboard and
foot part at desired height and adjust supporting foot at the
floor height. Start with the side of head part. If it is not possible
to mount the centre support rail, slightly loose the screws of
corner angles at foot part. Aer connecting of centre support rail
tighten the screws again.
9. Mount slatted frame angles at
corner connectors and at side panels
in accordance with the hight of
centre support rail.
Angles for side panels.
Insert depth of slatted frame is
height-adjustable from approx.
12,5-22 cm.
10. Place slip cover (with velcro part inwards)
onto corpus of bed.
(Do not yet remove the so side strap of velcro!)
12. Aer you have placed the cover properly onto
the corpus, remove the velcro (so side strap)
carefully and fix the cover.
11. Pay attention that the corner
seams are exactly oriented at mitre
and the parts of zipper/box pleat
hang down exactly at the 2 edges in
front.

6002 LETTO
© 2015 K URT BEI E R &KATI QU I N G E R
13. With zipper-cover-version the zipper
at head- or foot parts can be opened
and closed at will.
Complete covered corpus of bed!
Due to a functional fitting both back parts are height-adjustable. To
adjust the back, grasp it centrally and pull it up- or downwards in the
desired position.
Functional back for a flexible high back comfort
Insert depth for slatted frame: approx. 12,5-22 cm
(measured from top edge of bed frame)
Instruction manual

6002 LETTO
© 2015 K URT BEI E R &KATI QU I N G E R
Centre support rail
Support angle
Insert depth approx. 17 cm
Centre support rail
Support angle
Insert depth approx. 19,5 cm
Centre support rail
Support angle
Insert depth approx. 22 cm
Centre support rail
Support angle
Insert depth approx. 17,5 cm
Centre support rail
Support angle
Insert depth approx. 15 cm
Centre support rail
Support angle
Insert depth approx. 12,5 cm
Slatted frame assembly
with wooden foot 13 cm
Keep all documents relating to the purchase of your furniture carefully, even beyond the legal warranty period of 2 years. You will
find all important information in your product folder and also on our website www.bullfrog-design.com
120mm
-
235mm
120mm
-
235mm
120mm
-
235mm
120mm
-
235mm
120mm
-
235mm
120mm
-
235mm