BWI Eagle AIR-EAGLE XLT Manual

PRODUCT INFORMATION
BULLETIN
457 ROUTE 422 EAST ?BUTLER, PA 16002 ?724-283-4681 ?( FAX) 724-283-5939 ?www.bwieagle.com
AIR-EAGLE®XLT
R.F. Transmitter
MULTI CONTACT INPUT
MODEL 44-1000-PI
DESCRIPTION
The model 44-1000-PI, AIR-EAGLE XLT TX IS a multi contact input R.F.
transmitter
designed to transmit unique signals to the model 44-2000-PI AIR-
EAGLE XLT RECEIVER.This model is specifically designed to interface with a
relay output card for activating remote lightning warning beacons. This unit
features a test button for transmitting a test signal to all receivers which
insures signal integrity.
DIMENSIONS & INDICATORS
Top View
Side View
CH1 CH2 CH3
Input
Test
5.50 "
6.30"
CH1 LED -Yellow LED illuminates continuously when the
yellowwarning beacon contacts are closed.
CH2 LED -Red LED illuminates continuously when the red
warning beacon contacts are closed.
CH3 LED –Green LED illuminates continuously while the test
button is being depressed.
TEST PUSHBUTTON –A momentary pushbutton used to send a
transmit a test signal to the receiver.
PC BOARD SET-UP INFORMATION
Dc Power Input Module
Open
Closed
SEL1
2
amp
+-
DC IN
INP1 TERM2
1234 1234
NSW1
1 2
Make the following connections on the PC Board Terminal Strip:
DC INPUT TERMINAL STRIP (DC IN)
Terminal 1 Positive (+) 12VDC INPUT from 120VAC adapter
Terminal 2 Negative (-) 12VDC INPUT from 120VAC adapter
INPUT 1 TERMINAL STRIP (INP1)
Terminal 1 CH1 Dry Contact Input (+)
Terminal 2 CH1 Dry Contact Input (Common)
Terminal 3 CH2 Dry Contact Input (+)
Terminal 4 CH2 Dry Contact Input (Common)
I/O TERMINAL STRIP (TERM2)
Terminal 1 CH3 Test Switch Input (+)
Terminal 2 CH3 Test Switch Input (Common)
NETWORK SWITCH TERMINAL STRIP (NSW1)
Terminal 1 Not Used On This Model
Terminal 2 Not Used On This Model
NETWORK SWITCH CONFIGURATION OPTIONS (SEL1)
SW # OPEN CLOSED
SW1 Not Used Not Used
SW2 Not Used Not Used
SW3 Not Used Not Used
SW4 Not Used Not Used

AIR-EAGLE®XLT
R.F. Transmitter
MULTI CONTACT INPUT
MODEL 44-1000-PI
SPECIFICATIONS
Power Supply 120VAC from wall adapter
Fuse Protected 2 amp
Transmit Frequency 900MHz Spread Spectrum
Transmit Range Up to 10 miles with external
antenna -see accessories)
Enclosure Fiberglass NEMA 4, 4x, 12 + 13
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main) 44-1002-PI
Air-Eagle XLT Receiver 44-2000-PI
Replacement Transceiver Antennas:
900MHz Omni Directional Base Antenna (For
Distances Of Up To 10 Miles *) 49-3101
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly
used and installed, will be free from defects in material and workmanship
for a period of 6 months after date of purchase. Said warranty to include
the repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eagle makes no express warranties beyond
those stated here. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allow the exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss during shipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 1-Mar-02
457 Route 422 East
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com