C.A. Technologies Lynx 300H User manual

HVLP AIR CAP AND FLUID NOZZLE CHART
MODEL
NO. AIR CAPS Press / Siphon
*MAX GUN
INLET PRESS.
FOR HVLP
FAN
CONTROL
SCFM @
MAX GUN
INLET
AIR CAP
RING
AVAI LABLE F LUI D
NOZZLES TIPS
NEEDLES /
marking on needle
23-1008 pressure 40** 13.5 33-0208 0.8mm (.022") 40-1308 (308)
23-1010 pressure 40** 13.5 33-0210 1.0mm (.040") 40-1310 (310)
23-1012 pressure 40** 13.5 33-0212 1.2mm (.046") 40-1312 (312)
23-1013 pressure 40** 13.5 33-0213 1.3mm (.052") 40-1313 (313)
23-1014 pressure 40** 13.5 33-0214 1.4mm (.055") 40-1314 (314)
23-1015 pressure 40** 13.5 33-0215 1.5mm (.059") 40-1315 (315)
23-1017 pressure 40** 13.5 33-0217 1.7mm (.070") 40-1317 (317)
23-1019 pressure 40** 13.5 33-0219 1.9mm (.075") 40-1319 (319)
23-1022 pressure 40** 13.5 33-0222 2.2mm (.086") 40-1322 (322)
Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)
*Note: Air cap test gages are available to confirm HVLP compliance.
*Gun inlet pressures may vary as required by application
**When using optional gun regulator, inlet pressure changes to 45psi
IncludedL300H 60-1502 (#2)
LL
LL
Lynx 300Hynx 300H
ynx 300Hynx 300H
ynx 300H
PRESSURE FEED SPRAY GUN
PRODUCT INFORMATION
Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: [phone], Fax: [phone]
www.spraycat.com

Operation and Maintenance Instructions for
L300HL300H
L300HL300H
L300H Spray Guns
Operation
1. Connect air supply hose at handle of gun.
2. Connect a pressurized fluid supply to the gun fluid inlet.
3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control
fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.
4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.
Maintenance
IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.
Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.
1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures
instructions.
2. If a gun cleaner is not being used:
Remove air cap and clean separately using clean solvent.
For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow
thru the gun until clean.
NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.
Gun head disassembly and reassembly instructions:
Have repair kit # 10-106 available before gun disassembly.
Gun head disassembly
To remove the nozzle carrier (4) and air cap adapter (6):
1. Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body (3), and needle (13).
2. Remove the needle seal cartridge (23).
3. Loosen the locknut (9) and remove fluid inlet (10) using a 5/8” open-end wrench.
4. The nozzle carrier (4) and air cap adapter (6) will now slide forward from the gun body (11).
Gun head reassembly
1. Install a new o-ring (5 and 7) on the air cap adapter (6).
2. Install the thread locknut (9) onto the fluid inlet (10) as far as possible.
3. Install a new fluid inlet seal (8) into the recess area on the nozzle carrier (4) inlet port.
4. Slide the nozzle carrier (4) into air cap adapter (6) and insert into the gun body (11) as far as possible. Be sure the
nozzle carrier (4) extends into the hole at the back of the gun head. Install the needle seal (23) but do not tighten.
5. Rotate the nozzle carrier (4) until the fluid inlet port in the nozzle carrier (4) is aligned with the threaded hole in the
body. While in this position, insert the fluid inlet (10) and tighten firmly.
6. Tighten the needle seal (23) to approx. 12 ft.-lb. torque.
7. Tighten the fluid inlet (10) to approx. 25 ft.-lb. torque.
8. Tighten the locknut (9) to approx. 33 ft.-lb. torque.

23-1015-G
23-1022-G
23-1017-G
23-1019-G
HVLP AIR CAP TEST GAGES
23-1008-G
23-1010-G
23-1012-G
FOR
L300H
GUNS
23-1013-G
23-1014-G
ITEM NO. PART NO. DESCRIPT ION ITEM NO. PART NO. DESCRIPT ION
1 See Air Cap Chart Air Cap** 16 60-204 Needle Return Spring*
2 See Air Cap Chart Fluid Nozzle Tip** 17 60-201 Rear Bushing
3 33-1201 Fluid Nozzle Body 18 60-119 Seal*
4 60-L31H Nozzle Carrier 19 60-1520 Air Valve Assembly
5 98-8026 O-Ring* 20 60-302 Air Valve Poppet
6 60-34H Air Cap Adapter 21 60-125 O-Ring*
7 60-131 O-Ring* 22 61-1003 Air Valve Spring*
8 60-124 Fluid Inlet Seal* 23 60-1400 Needle Seal Cartridge*
9 60-128 Locknut 24 60-2101 Trigger
10 60-126 Fluid Inlet Fitting 25 60-1510 Air Control
11 60-1114 Lynx Gun Body HVLP 25A 60-122 Plug (optional)
12 See Air Cap Chart Fan Control Assembly** 26 60-104 Air Inlet Fitting
13 See Air Cap Chart Fluid Needle** 27 60-1033 Trigger Pivot Set
14 60-202 Fluid Control Knob 28 98-0109 Allen Plug
15 60-205 Spring Seat*
**See air cap selection chart on page 1
*Indicates part included in repair kit # 10-106
*
*
*
*
*
*
**
*

L300H HVLP SPRAY GUN
MATERIAL TYPE FLUID ORIFICE x
AI R C AP
MAXIMUM
PATTERN WIDTH PRESS. / SIPHON
Very Thin
less than 16 sec. Zahn #2
inks , dyes,
solvents, stains
Thin
16 to 20 sec. Zahn #2
lacquers, enamels,
primers, sealers
Medium
21 to 30 sec. Zahn #2
automotive base coat
enamels, primers
epoxies, urethanes
automotive clear coat
Heavy
over 30 sec. Zahn #2
heavy body primers
high solid enamels
high solid automotive coatings
adhesives
P
P
1.3 mm x 1013
1.5 mm x 1015
1.7 mm x 1017
12
12
12
P
P
P
1.5 mm x 1015
1.7 mm x 1017
1.9 mm x 1019
2.2 mm x 1022
12
12
12
12
P
P
P
P
FLUID NOZZLE / AIR CAP SELECTION CHARTS
LYNX Series 300H - Pressure Feed Guns
1.0 mm x 1010 12 P
1.0 mm x 1010
1.3 mm x 1013
12
12
Revised 3/18/14