CABINETS TO GO Findley & Myers CB33 User manual

Lazy Susan Cabinet
ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all base reach Lazy Susan
ITEM# CB33, CB36
Page 1

Page 2
► Items Quantity:
Item Description Qty
Face Frame (A1) & Short Face Frame (A2)
2
Side Panels {Left (B1) and Right (B2)}
2
Left Rear Side Panel
1
Right Rear Side Panel
1
Bottom with Turntable
1
BackPanel
1
Shelf with Turntable
1
Long Toe Kick (H1) & Short Toe Kick (H2)
2
Hardware Box:
1
1/2" flat head screws 12pcs, Door Hinge with screws 2 sets, round buttons 4pcs, (pre-installed magnetic latch & plate)
Door s (J1) & (J2)
2
►Required Tools:
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT
1-800-CABINET.
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
a b e
Qty 16
Lazy Susan
Installation
f
Qty 2
Sets
cd
Qty 4Q ty 5 Qty 10 Qty 12
►Hardware Box:
g
Qty 2
Sets
A
B
C
D
E
F
G
H
I
J
Plastic Corner Braces 5pcs, 1/2" Large Round Head Screws 16pcs, Invisible Hinge with Screws 2 sets , 1/2" Round Head Screws 10pcs,
J1 J2
A1
A2
B1 B2
C
D
F
H1
H2
G
E
(Behind Doors)
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

Page 3
►
Instructions:
1. Assembling the Door Set : Place two doors (J1&J2) on a flat surface and align them from the pilot holes. 
Attach them together using the invisible hinge sets (f) and the provided screws, and set aside.
2. Place face frame (A1) face down on a flat soft working surface (Figure 1) .
A1
3. Insert left side panel (B1) into the grooves of face frame (A1) on the magnetic latch
side. Align the plastic half part of the cam lock connectors. Make sure it fits and lock
connectors with screwdriver by turning the screw located on the cam lock connector
to the right 180° (Figure 2) Stand up side panel up right at this time . (Figure 3)
Figure 3
4. Insert the bottom (E) with turntable through face frame resting it in the groves provided on the side panel. (Note: If the turntables are not assembled
to the bottom and shelf, go ahead and attach
them at this time before completing Step 4.)
B1
A1
E
Figure 4
5.
Insert Right Rear Side Panel
(D)
connect with the face frame (A1). Insert Left Rear Side Panel (C) (Figure 5) Align the cam lock connectors and lock.
B1
D
Figure 5
6. Place the back panel (E) connect with rear side panels and align the cam lock connectors. (Figure 6) Align the cam lock connectors and lock.
C
E
D
Figure 6
7. Insert shelf with turntable (G) into position, align the cam locks under the shelf and lock. (Figure 7)
G
Figure 7
f
Qty 2
Sets
Figure 2
C
(Note: If the doors are already
assembled, please continue to Step 2)

Page 4
8. Place the Right Side Panel (B2) and align the cam lock connectors with right rear side panel. (
Figure 8) Lock the cam lock connectors.
Place the Short Frame (A2) and align the cam lock connectors with the side panel (B2) and frame (A1) and lock the cam lock connectors.
Figure 8
9. Place and attach door assembly (J) from Step 1 onto face frame (A2) using door hinges (g) and screws (d) (Figure 9)
10. Installing the Corner Braces (Figures 11&12):
Position and insert the 5 plastic
corner braces (b) in the locations shown in (Figures 11&12)
secure them with ½”
screws (c). Install round buttons (a) onto the doors where they contact the frames.
Figure 12
Figure 11
J1 J2
Figure 9
Qty 2
Sets
A2
a b
Qty 4Q ty 5
c
Qty 10
Attach the short toe kick (H2) to long toe-kick (H1) with cam locks, then put onto the cabinet under the door. Make sure that all fit and lock the
cam lock connectors. Reposition the cabinet, laying it on the back panel,(Figure 10) lock cam locks to the frame under the door. Return cabinet to
upright position.
g d
Qty 12
Figure 10
H1
E
H2

Page 5
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do
not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on ch rome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.