CABINETS TO GO Findley & Myers CBD36 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Corner Cabinets
CBD36
Page 1

►Items Quantity
Item Description Qty
A
Left Back Side Panel 1
B
Right Back Side Panel 1
C
Frame & Doors: (1 Lower Door, 1 False Drawer Front)
1
D
1
E 1
F
Left Front Side Panel
1 Set
G
Hardware Box
1
Bumper 2pcs, 1/2" Round Head Screws 8pcs, Metal 135° Brackets 4pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a
bc
Qty 2 Qty 4Qty 8
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
Toe Kick
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
Bottom Panel
Back Panel
Right Front Side Panel
1
H

H
D
E
1
2
SoftSurface
Hard Surface
F
F
Figure 2
Page 3
Figure 1
Assemble the Side
Panels (E,D) onto the
Frame (F) by
connecting the male
and female cam locks
and using a screwdriver
to turn the lock
clockwise. (Figure 1)
{ NOTE: Assemble cabinet
parts on a flat smooth soft
work surface. }
Insert the bottom panel (H) into
the slots of the side panels and
lock the cam lock connector.
(Figure 2)

C
B
A
3
4
Figure 3
Figure 4
Assemble the back side panels (A,B) onto the front
side panels and bottom panel.
(Figure 3)
Page 4
Install the back panel (C) into the
position shown. {
NOTE: You may
need to gently spread the back
panels to seat the cam locks. }
(Figure 4)

5 Install the toe kick (G) to the assembled cabinet. You may lay the cabinet face down
on a soft flat surface to better install the brackets (b) using screws (c).
Figure 5
Page 5
G
b X4
X8
c
(Figure 5)

►Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets
etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to
get the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care
by email - [email protected] or call 1-800-CABINET.
Page 6
a X2
a
6Install the bumpers (a) onto the door
at the corners where the door comes in
contact with the frame.
(Figure 5)