CABINETS TO GO Findley & Myers BC36 User manual

Page 1
Double Drawer Base Cabinet
ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all double door double drawer base cabinets.
ITEM # BC36

Page 2
►Items Quantity
►General Instructions:
Thank you for purchasing a Cabinets To Go product. You are now the proud owner of a high quality product designed
to face the test of daily use and guaranteeing your enjoyment for many years to come.
Carefully read the instructions before starting the installation.
During assembly, please follow all generally accepted safety procedures.
Failure to adhere to the following instructions will invalidate the warranty and Cabinets To Go will decline any responsibility for any
damages caused. Any installation which does not correspond to the instructions may result in defects, malfunctioning parts, significant damage and/
or injury.
Before the assembly begins, check that all appropriate and required plumbing and electrical connections exist.
Before drilling, make absolutely sure that there are no pipes (gas, water,electricity, heating, etc.) at the drilling location. Cabinets To Go will not
be held responsible for failure to follow these instructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE
PARTS IN THE QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE
IMMEDIATELY AT 1-800-CABINET
►Required tools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a b ge
Qty 24
f
Qty 6 -10
cd
h
Qty 4Qty 4 - 2 Sets Qty 12 Q ty 4 Qty 8 Qty 4
H
A
G
H
A
F
B
D
B
C
E
Item Description Qty
A Face Frame with Doors 1 (2)
B Side Panels 2
C Bottom Panel 1
D Back Panel 1
E Shelf 1
F Toe Kick 1
G Drawer Fronts 2
H Drawer Box: Front 2pcs, Back 2pcs, Sides 4pcs, Bottom 2pcs 2
I Hardware Box: 1
Bumpers 12pcs, Plastic corner bracket 4pcs, 1/2" round head screws 8pcs, Shelf clips 4 pcs, 1/2" flat head screws for slide 24pcs
1" screws 6-10pcs, Slide Rails 4 Sets, Slide Rail Supports 4pcs
G
A
H
x2
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

Page 3
►Instructions:
1. Place the face frame (A) face down on a flat soft working surface to ensure that the face is not
scratched or damaged (Figure 1) .
2. Installing the Side Panels (Figure 2): Insert right and left side panels (B) into the grooves of
the face frame (A) and align the cam lock connectors (Figure 2). Lock the cam
with a screw driver by turning the screw 180° clockwise (Figure 4) .
3. Installing the Bottom (Figure 3): Gently spread the side panels and insert the bottom (C)
into the grooves of side panels (B) until it is seated in the face frame (A). Align it and lock each cam.
4. Installing the Back Panel and Toe Kick (Figure 5): Before you start this step, place the
back panel (D) on a flat surface facing upward. Install the drawer rail holders (g) in the pre‐
spotted area on the back panel (Figure 6). Secure them with 2 flat head screws (e) ( Figure 6). Then
put the back panel (D) at rear of side panels (B) (Figure 5) . Align and lock each cam lock. Install the
Toe Kick (F) by locking the cam lock at both ends (Figure 5).
g
D
e
Figure 1
A
Figure 2
B
B
Figure 4
Figure 3
B
B
C
Figure 6
D
F
B
Figure 5
Top
g
5. Installing the Shelves: Insert the shelf clips (d) (Figure 7) into the adjustable shelf holes on the side
panels (B) at the desired height and slide in the shelf (E) .
d
Qty 4
ge
Qty 8Qty 4
Figure 7
B

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwitha screwdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
G
H
8. Installing the Corner Braces (Figure 10) and inserting the Drawer: Place the corner
braces (b) on each top corner of the cabinet and secure them with the ½” Corner Brace Screws (c).
Slide the drawer into the rails and check the drawer position . Install the rubber bumpers (a) onto
the corners of the door and drawer front (G) where they contact the frame.
Figure 10
b
b c
Q ty 4 Qty 8
6. Install the Drawer Slide Rails: Insert the drawer side rail's back end (h) into the
holder (g) previously installed (Step 4) on the back panel (D) (Figure 8).
Then secure the drawer rail front end with 1/2” screws (e) using the pre‐drilled holes in the
face frame (A). The remainder of the screws can be used to secure the drawer to the rails.
7. Drawer Assembly (Figure 9): First assemble the drawer front (G) with drawer box front (H)
with screws (f). Then assemble the rest of the parts of the drawer box (H) using your palm, or a rubber
mallet if needed, to secure the dove tails into position. Repeat step for 2nd drawer.
f
Qty 6-10
a
Qty 12
Figure 9
D
F
B
Figure 8
Top
h
g
h
Qty 4 - 2 Sets
e
Qty 16

Page 5
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as
scrapers, metallic brushes, and other products which can scratch or tarnish surfaces. Under no circumstances
should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com
to get the specific details. If you have any questions with warranties or to make a claim, please contact
Customer Care by email - [email protected] or call 1-800-CABINET.