CABINETS TO GO Findley & Myers BC36 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Base Cabinets
ITEM# BC36
Page 1

►Items Quantity
Item Description Qty
A
Left Side Panel 1
B
Right Side Panel 1
C Back Panel
1
D Bottom Panel
1
E Frame & 2 Doors 1
F Shelf 1
G
Hardware Box
1
Bumper 12pcs, Shelf Bracket 4pcs, 1/2" Round Head Screws 32pcs, Plastic Corner Brackets 4pcs, 1" Flat Head Screws 8pcs, Glide Brackets 4pcs, Drawer Clips 4pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b
cd
Qty 4 Q ty 8 Qty 32 Qty 12
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
Toe Kick
e f g
Q ty 4 Qty 4Qty 4
H Drawer Panel & Drawer Box: (Front, Back, Sides, & Bottom)
I Drawer Glides
2 Sets
2 Sets

1
2
b X8
f X4
C
A
B
Assemble the Side Panels (A,B) onto the
Frame (E) by connecting the male and
female cam locks and using a screwdriver
to turn the lock clockwise. (Figure 1)
{NOTE: Lay Frame and Doors on a flat smooth soft
work surface to assemble.}
SoftSurface
Hard Surface
E
E
Install the glide brackets (f) to
the Back Panel (C) using
screws (b). (Figure 2)
Page 3
Figure 1
Figure 2

D
3
4
G
Figure 3
Insert the Bottom Panel (D)
into the groove of the Side
Panels and Frame.
(Figure 3)
Figure 4
Install the toe kick (G) onto
the side panels (A,B) and
lock the cam locks.
(Figure 4)
Page 4

C
5
X4
a
6
F
Figure 6
Page 5
Figure 5
Install the Back Panel (C)
onto the side panels (A,B)
and lock the cam locks.
(Figure 5)
Insert the shelf brackets (a)
into the side panels (A,B)
in the location of your
choosing. Install the shelf
(F)F onto the brackets.
(Figure 6)