CABINETS TO GO Findley & Myers CB33 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Lazy Susan Cabinets
ITEM# CB33, CB36
Page 1

►Items Quantity
Item Description Qty
A
Back Left Side Panel 1
B
Back Right Side Panel 1
C Back Panel
1
D Front Left Side Panel
1
E Front Right Side Panel 1
F Full Frame 1
G
Hardware Box
1
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a
bc
Qty 4 Qty 8Qty 8
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
Partial Frame
d
Q ty 8
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
e
Q ty 16
f
Q ty 4
g
Q ty 2
Bumper 4pcs, Door Magnets 2pcs, Plastic Corner Brackets 4pcs, ST2.9*16mm Screws 8pcs, ST3.5*16mm Screws 8pcs, ST12mm Screws 8pcs, ST14mm Screws 16pcs
H
1
Bottom Panel
I
1
Fixed Shelf
J
2
Turntables
K
1
Left Toe Kick
L
1
Right Toe Kick
M
1
Right Door
N
1
Left Door
O
2
165deg Hinges
P
2
Turntable Hardware

P
I
J
H
P
1
2
Figure 2
Page 3
Figure 1
SoftSurface
Hard Surface
H
H
Attach the turntable hardware (P) with
screws (e) onto the bottom panel (H) using
the pre-drilled holes. Then attach the
turntable (J) onto hardware (P). (Figure 1)
{ NOTE: Lay cabinet parts on a flat smooth soft
work surface to assemble. }
e
Q ty 8
e
Q ty 8
J
Same as Step 1, attach the turntable
hardware (P) with screws (e) onto the
Fixed Shelf (I) using the pre-drilled
holes. Then attach the turntable (J)
onto hardware (P). (Figure 2)

D
A
C
3
Figure 4
Page 4
Figure 3
B
F
4
C
D
D
A
B
Assemble the side panel (D) with back
side panel (A) by connecting the male
and female cam locks and using a
screwdriver to turn the lock clockwise.
Repeat this procedure by assembling
the back panel (C) with back side
panel (A). (Figure 3)
H
Assemble the back side panel
(B) with back panel (C) in the
same manner as described in
Step 3. Insert the full frame (F)
into position onto the bottom
panel (H) as shown. Then
insert the bottom panel (H)
into the bottom groove of the
assembled panels, and lock
the cam locks. (Figure 4)
NOTE: Step 4 may be easier to
complete with the assembled
back panels against a wall or
some other sturdy structure.

K
L
E
G
6
5
Figure 6
Page 5
Figure 5
Assemble the side panel (E) to
back side panel (B). Then install
the partial frame (G) onto the full
frame (F) and side panel (E).
(Figure 5)
Attach the toe kicks (K&L) together, then
install them to the assembled cabinet.
{ NOTE: You can lay the cabinet on the back panel at this
point to better reach the cam locks underneath. }
(Figure 6)
F
B

X8
a
X4
c
I
8
7
Figure 8
Page 6
Figure 7
Attach the fixed shelf (I) from Step 2 to
the cabinet by maneuvering the tray
around the frame then down into
position and connecting the cam locks
on side panel (D) & back side panel (B).
(Figure 7)
Install the corner brackets (a) into
the top corners shown using
screws (c). (Figure 8)
D
B

9
Figure 9
Page 7
Attach hinges (O) with screws (d), and door magnets (g) with screws (b).
Install the bumpers (f) to the inside of the doors in the locations shown.
(Figure 9)
X4
b
f X4
X2
N
M
O
X4
d
g
g

X4
d
11
10
Figure 11
Page 8
Figure 10
Install the remainder of the door magnets (g)
using screws (b) into the full frame using the
pre-drilled holes. (Figure 10)
g X2
b X4
Attach the remainder of the hinges (O) using screws (d),
and attach the doors by connecting the hinge pieces together.
(Figure 11)
O

►Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets
etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by
email - [email protected] or call 1-800-CABINET.
Page 9